How to make a picture frame, how to make a picture frame yourself?

Materials: Vegetables, Glycerin, Container, Stencil (optional), Paper Towel, Picture Frame, Double-sided tape.

Step 1: Because glycerin preserves the color of the plant, it is best to choose fresh plant leaves rather than dead leaves. Choose to pick plant leaves in the morning or late afternoon to avoid wilted leaves.

Step 2: Choose a shallow, rust-proof container, such as a plastic tray, and mix glycerin and water in a ratio of 1:2, the water is best lukewarm, the amount of glycerin and water, depending on the number of leaves. Use 2 cups of glycerin and 4 cups of water to mix and submerge 15 leaves.

Step 3: Dip the cleaned leaves in the glycerol liquid.

Step 4: Once the leaves are completely submerged, gently place two plastic plates on top and place them in a cool place to soak the leaves for 3-4 days.

Step 5: After 3-4 days, remove the leaves from the glycerol liquid and place them on a paper towel, carefully wipe off the excess glycerin from the leaves, and let the leaves air dry for 1 hour.

Step 6: If you need extra leveling, you can put the made leaves in the middle of two pieces of wax paper, then put them in the book, and then press the weight on top of the book, about 3 days. Finally, put on the frame and you're done.

1. Go to the building materials market or buy online with wooden strips suitable for the size of the drawing, as shown in the figure below.

2. Pin the wooden strips into a rectangle, as shown in the figure below.

3. Then use an electric drill to carve grooves on the four sides, as shown in the figure below.

4. Press the silicone thread together with the cross-stitch cloth in the groove of the frame, as shown in the figure below.

5. Trim the corners with scissors, as shown in the figure below.

6. Tighten the canvas with a stretch pliers, as shown in the figure below.

7. Cut off the excess silicone wire after crimping, as shown in the figure below.

8. Use a paper cutter to cut off the excess fabric, as shown in the figure below.

9. Press the silicone wire tightly, as shown in the figure below.

10. Use a code nail gun to fix the four corners of the frame and the silicone wire to prevent the line from coming out, as shown in the figure below.

Materials: hard paper, scissors, brushes, etc.

1. Prepare a piece of hard paper to draw a rectangular outline with a pencil, and cut out the frame with scissors.

2. In the next operation, use double-sided tape to paste three sides and attach a piece of paper.

3. At this time, it is time to test the scissor worker, and cut the egg tray into a beautiful shape.

4. It needs to be glued to the corner of the photo frame.

I did it myself in their kind of shop. Here's how:

Measure out the wood line according to your size and let out 2 more wood line width squares after sawing down, this Han Ji Feng Jiu Feng Xun Mo wood line is sawed at a 45 degree angle at both ends, and then put together into a rectangle, the connection can be bonded with white latex (it is transparent after drying, which does not affect the appearance), or use air nails (there is a nail tip without a nail tail cover with a nail gun) or use a small thin nail (you can use a hammer to nail the nail). After nailing, place it face down on the table, use plywood or compression board as the back panel, and thin glass as the surface (fixed with gun nails or glued to the wooden wire frame with double-sided tape). After the frame is completed, place it between the back plate and the glass plate**.

The frame is drawn as follows:

1. First of all, you need to know the national standard for commonly used paper sizes, and the following figure lists the national standards of A0, A1, A2, A3, and A4. Drawings generally need to be mapped to reserve the binding edge, ** in the blank 2 refers to the distance between the drawing area and the drawing frame when the binding edge is reserved.

2. Let's start to draw the A4 frame, first open the CAD and create a new blank file.

3. Click the format unit in the menu, set the longitude to "0", the unit to "mm", and click OK after setting.

4. Open the Layer Manager, a map frame layer. (The frame is a separate layer, which is easy to manage).

5. Select a rectangle in the drawing, or enter the command rec to draw a rectangle with a length of 297mm and a width of 210mm.

6. Then draw the drawing area, reserve the grouting line according to the standard, and the drawing area is 5mm away from the drawing frame.

7. Use the offset command: o to offset the drawn rectangle inward by 5mm. Then adjust the left border of the inner rectangle, and the left border is 25mm away from the left frame.

Frame Introduction:

A drawing frame refers to a wireframe that defines the drawing area on a drawing in engineering drawing. The drawing frame must be drawn with a thick solid line. There are two types of frame formats: with and without binding, but only one format can be used for the same product drawing.

The size of the frame should be in accordance with the specified pants and format. Drawings that need to be copied in miniature should have an accurate metric scale attached to one side and a centering mark on the four perimeters. The total length of the metric scale is 100 mm, and the grid is 10 mm.

The centering mark is drawn at the midpoint of the frame line, and the line width should be 5mm when it extends into the frame.

1. Go to the building materials market or buy online with wooden strips suitable for the size of the painting.

2. Pin the wooden strips into a rectangle.

3. Then use an electric drill to carve grooves on the four sides.

4. Press the silicone thread together with the cross-stitch cloth in the groove of the frame.

5. Trim the corners with scissors.

6. Tighten the canvas with a stretch pliers.

7. Finish cutting off the excess silicone wire.

8. Use a paper cutter to cut off excess fabric.

9. Press the silicone wire tightly.

10. Use a code nail gun to fix the four corners of the frame and the silicone wire to prevent the line from coming out.

Then the frame is ready. The materials and tools used in this step can be purchased at the building materials market, art supply stores, or online.

The practice of the photo frame is as follows:

Materials for making picture frames: cardboard, colored cardboard, double-sided tape, carving knife, scissors, ruler.

Steps: 1. Disassemble the box, put ** into it, and decide the size of the photo frame.

2. Cut the cardboard and compare it again to observe if there is anything to be modified. First use a pencil to draw the position of ** on the cardboard, then reduce the border, draw a line inward 2 3mm, and then crop.

3. Draw a line inward. If there is a problem with uneven trim during the cropping, you can make a slight modification, as long as it does not exceed the border that Qinghao originally drawn.

4. When cutting, press the required part under the ruler, so as to avoid the blade Xiaomin scratching the required part of the cardboard.

5. The thickness of the cardboard is thick, please be merciless when you go under the knife, and try to be fast and accurate.

6. Select a background color.

7. Draw the outline of the photo frame on the cardboard.

8. Draw a parallel line between the outer edge of the outline line of the ** frame and its interval of 2 3mm (the thickness of the hard board). Because the cardboard is to be wrapped entirely in cardboard, be sure to pay attention to the thickness of the cardboard.

9. Draw straight lines. Place the two rulers perpendicular to the edge of the jammed paper with the length of the ruler inside the jam paper as the required width, and then place the third ruler on it.

10. Direct folding.

11. Cardboard folding.

12. If it is directly folded, there will be intermittent short lines around the fold line, which is very unsightly. Therefore, the folded line should be gently crossed with a carving knife first, leaving a shallow mark before folding. (The left side is folded with a carving knife, and the right side is a folded lifter cover.)

13. Then all kinds of cutting.

14. Cut and fold.

15. Wrap the cardboard.

16. Continue to wrap another piece according to the above method.

17. Stick double-sided tape on the inside of the cardboard and stick the edges.

18. Both pieces are wrapped.

19. You can put different sizes of **.

Jinhua Jindong District Wanchuang craft photo frame factory has handmade picture frames.

Steps: 01 Prepare a thick piece of cardboard and draw the size of the desired phase bar on the cardboard. And cut out the position of the middle photo with scissors.

02 is like a five-inch ** photo frame than Qi Xingdong, the size of the inner frame is almost 12*9cm, the outer frame is almost 13*17cm, and each side of the book is left with about 2cm.

03 Then I have to prepare a board on the top of the photo frame, and then there is a board on the back of the piece and cut it with a paper cutter.

04 Then just glue the two boards together, and then you can make a small shelf and stick it behind the photo frame, and the high-withered photo frame is completed. If you think the picture frame is too plain, you can decorate the border with something or draw some pictures, okay.

Hello, happy to answer for you. The way to draw the frame of the painting is; 1. Draw a rectangle, draw diagonal lines at the four corners, and draw a rectangle in the middle; 2. Draw a triangular hook at the top and a small circle in the middle; 3. Start coloring, paint the frame brown, and paint the glass in the frame with light blue lines. The benefits of drawing are; Enrich your personal life, it allows you to learn to deal with the life of a person who is excited, with painting, you are no longer lonely and have nothing to do, pick up the pen, return to the code to concentrate, a painting is an hour or two, not only can you spend no time, but also can get a strange satisfaction from it.

Make you more confident that a person who can draw is like having a skill, whether it is in school, in a training class, in a collective environment, as long as there is an opportunity to paint, you will find that you have your own advantages, so you will be more confident in leaking lead, which is because this is a technique and not a bubble. <>