HP 1010 printer leakage, HP 1020 printer ink leakage how to deal with

Reason: There is a defect in the occlusion between the cleaning hanging piece and the photosensitive drum surface in the toner cartridge, and the residual powder cannot be cleaned normally, resulting in the overflow of fine residual powder, causing gray bottom, black bottom, black spots and black blocks on the paper surface. In fact, it was caused by you disassembling the toner cartridge.

Solution: Try to reassemble, pay attention to the position of the 2 slightly yellowed plastic slender cleaning tabs in the drum is normal, whether there is deformation, and if it is abnormal, adjust it.

In fact, the chance of being able to adjust the scraper after leakage is not large, so be prepared to replace the drum with a new one.

The sea-like roller is the rechargeable roller, which is outside the cartridge, inside the machine, and is in contact with the green drum. If you change this thing, it shouldn't cause the toner cartridge to leak. I guess you're talking about the magnetic roller with a lot of powder in the toner cartridge.

Remember to be careful when using it in the future, the toner cartridge is very fragile, and foreign objects can easily cause damage.

Are the magnetic rollers you are talking about inside the toner cartridge? You say sponge-like again? Those are two things. Depending on what you said the question could be:

1.The sponge roller is not the right model, and it will be too thin.

2.Toner is damp.

3.There is too much waste powder, so clean up the waste powder and take a look. That is, after you dismantle the sponge roller and knock it on the ground, the waste powder will come out.

4.I don't know how you changed the roller, if you really dismantle the magnetic roller, you must pay attention to the copper ring next to it when this thing is installed, it will be printed incompletely if it is deformed, and it will be printed without words if it is broken, 5Do you have something like a spring on the side of the toner cartridge installed?

If the roller you are talking about is not in the toner cartridge, then the fixer film is broken, you see if those powder stains can be wiped off, if you can, the problem is in the fixer, if not, the problem is in the toner cartridge.

You'd better pass on a picture.

Summary. Hello dear, I will answer for you this time, please be patient. <>

<>1. Too much ink is added, especially for color cartridges. If the volume of monochrome is less than 1 3 of the volume of the black cartridge, the amount of filling is too large and the number of fills is increased, which may cause ink leakage. Workaround:

The suggestion is to configure a small scale, preferably an electronic scale, so that you can grasp the amount of ink you fill the cartridge at any time; At the same time, pay attention to the ink cartridge that leaks ink and do not put it into the printer first, you can place the ink cartridge in the tray with the print head facing down, wait for the ink to no longer leak, then wipe the ink cartridge chip and load the ink cartridge into the printer. Once the ink comes out of the vent, the syringe must be withdrawn, and the amount of ink inside the ink cartridge must be appropriately reduced, which is conducive to solving the ink leakage. 2. The sponge is full.

Common inkjet printers have a sponge of waste ink on the bottom. When the sponge is full, the ink overflows. Workaround:

Take the sponge out, wash it and put it back on, or replace it with a new sponge. 3. Problems with the cartridge itself. Generally, the original ink cartridge is relatively rare, and the quality of the optional ink cartridge is uneven, and the ink cartridge itself may leak or cause hole blockage.

Workaround: Switch to high-quality cartridges.

How to deal with ink leakage from HP 1020 printer.

Hello dear, I will answer for you this time, please be patient. <>

<>1. Too much ink is added, especially for color cartridges. If the volume of monochrome is less than 1 3 of the volume of the black cartridge, the amount of filling is too large and the number of fills is increased, which may cause ink leakage. Workaround:

The suggestion is to configure a small scale, preferably an electronic scale, so that you can grasp the amount of ink you fill the cartridge at any time; At the same time, pay attention to the ink cartridge leaking ink cartridge first do not put into the printer, you can print the head down to place the ink cartridge in the plate, wait for the ink to no longer leak, then wipe the ink cartridge chip and load the ink cartridge into the printer. Once the ink comes out of the vent, the syringe must be withdrawn, and the amount of ink inside the ink cartridge must be appropriately reduced, which is conducive to solving the ink leakage. 2. The sponge is full.

Common inkjet printers have a sponge of waste ink on the bottom. When the sponge is full, the ink overflows. Workaround:

Take the sponge out, wash it and put it back on, or replace it with a new sponge directly. 3. Problems with the cartridge itself. Generally, the original ink cartridge is relatively rare, and the quality of the optional ink cartridge is uneven, and the ink cartridge itself may leak or cause hole blockage.

Workaround: Switch to high-quality cartridges.

My printer is using toner.

HP 1020 model.

Printed out are vertical lines.

Toner residue can be seen on the drum core.

Which part is the problem?

1. Replace the toner cartridge, a new drum should be replaced again after adding 2-3 times of disadvantages, and try to use environmentally friendly toner cartridges of large companies or Luzhen brands, such as Jin Huida. 2. Re-add powder, if you add powder manually, choose high-quality toner when buying toner, which has better compatibility; 3. Rent and clean up the waste powder warehouse.

Summary. 1. Open the machine and take out the toner cartridge, clamp the metal pin on one side with diagonal pliers, pull it out forcefully, and the silver metal pin on both sides can be divided into two parts after pulling out, the one side with the drum core is the waste powder collection piece, and the one side with the magnetic roller is the powder supply part.

Second, clean up the waste powder: the waste powder collection in the light blue drum on both sides of the metal positioning pins set out, take out the drum in a dark and stable place, take out the discharge roller, and then unscrew the two nails on the scraper, remove the scraper, slowly pour out the waste powder in the waste powder warehouse, and then restore the scraper, discharge roller, and photosensitive drum according to the original position (if you need to replace the drum core, scraper at this time, the old drum core, scraper can be replaced with a new one).

3. Filling toner: unscrew down the screw nail on the gearless side of the magnetic roller on the powder supply part, take off the plastic shell and you can see a purple plastic cover, open this cover, clean up all the toner in the powder bin and the magnetic roller (if you do not clean up the magnetic roller and the powder bin printing sample, there may be bottom ash or shallow handwriting), the magnetic roller is loaded, and the magnetic roller should be pressed and held down at this time to prevent the magnetic roller from leaving the original position. Shake the laser printer toner evenly and slowly pour it into the powder supply bin, cover the plastic cover, and put on the plastic shell (at this time, it should be noted that the semicircle on the end of the central shaft of the magnetic roller is in line with the semicircular hole on the plastic shell).

How to clean up the leakage of HP M104W printer.

1. Open the machine and take out the toner cartridge, clamp the metal pin on one side with diagonal pliers, pull it out forcefully, and the silver metal pin on both sides can be divided into two parts after pulling out, the one side with the drum core is the waste powder collection piece, and the one side with the magnetic roller is the powder supply part. Second, clean up the waste powder: the waste powder collection piece in the light blue drum on both sides of the metal positioning pins set out, take out the drum in a dark and stable place, take out the discharge roller, and then unscrew down the two nails on the scraper, remove the scraper, send the burial slowly pour out the waste powder in the waste powder warehouse, and then restore the scraper, discharge roller, and photosensitive drum according to the original position (such as the dust ant needs to replace the drum core, scraper at this time the old drum core, scraper can be replaced with a new one).

3. Filling toner: unscrew down the screw nail on the gearless side of the magnetic roller on the powder supply part, take off the plastic shell and you can see a purple plastic cover, open this cover, clean up all the toner in the powder bin and the magnetic roller (if you do not clean up the magnetic roller and the powder bin printing sample, there may be bottom ash or shallow handwriting), the magnetic roller is loaded, and the magnetic roller should be pressed and held down at this time to prevent the magnetic roller from leaving the original position. Shake the laser printer toner evenly and slowly pour it into the powder supply bin, cover the plastic cover, and put on the plastic shell (at this time, it should be noted that the semicircle on the end of the central axis of the magnetic roller is in line with the semicircular hole on the plastic shell).

Fourth, install and restore the powder supply parts and waste powder collection parts according to the position when they are disassembled, and insert the metal bayonets on both sides of the cavity circle. After the toner cartridge is installed, the photosensitive drum baffle should be pushed open, and the side gear of the dust-free drum core should be gently turned upwards for several turns, and the residual toner on the collapsed surface of the drum will be removed, and the machine can be used after installation.

Wait a minute, I'll look for it.

Ok thanks!

Summary. HP 132A printer powder leakage and solutions: a:

The print coverage is too low, resulting in too much waste ton, and the print coverage rate refers to the percentage of the area covered by the ink relative to the area of the entire printing paper during the printing process, that is, how much of the printed product occupies the total area of the paper. Due to low coverage printing, it is easy to waste toner, resulting in waste toner spillage and leakage. Solution:

In this case, you need to clean up the waste toner bin or replace it with a dot matrix printer or a toner cartridge suitable for low-coverage printing. 2: Powder adding causes deformation and damage to the blade, and improper powder operation is also an important cause of powder leakage.

If the printer is added twice after buying, it is easy to cause the deformation of the waste toner bin during disassembly and assembly, and then leak the powder! Solution: In this case, you can only consider replacing the toner cartridge.

Three. There are large particles of impurities clogged between the magnetic roller and the scraperThe toner leakage of the printer drum may also be caused by the blockage of large particles of impurities between the magnetic roller and the scraper, solution: We can try to disassemble the toner cartridge for inspection to remove the impurities.

Mixing toner of different brands or qualities can easily cause waste toner residue and even cause large particles of impurities to clog! ​

Hello, dear, this question is up to me, HP 132a printer leaks, it takes time to type, please be patient.

HP 132A printer powder leakage and solutions: 1: The printing coverage rate is too low, resulting in too much waste powder, and the printing burn-up coverage rate refers to the percentage of the area covered by the ink relative to the area of the entire printing paper during the printing process, that is, how much the printed product occupies the total area of the paper.

Due to the low coverage printing, it is easy to waste toner, resulting in waste toner overflow and powder leakage. Solution: In this case, you need to clean up the waste toner bin or replace it with a dot matrix printer or a toner cartridge suitable for low-coverage printing.

2: Powder adding causes deformation and damage to the blade, and improper powder operation is also an important cause of powder leakage. If the printer is bought back and added the leather scale blind powder twice, it is easy to cause the deformation of the waste toner bin during disassembly and assembly, and then leak the powder!

Solution: In this case, you can only consider replacing the toner cartridge. Three.

There are large particles of impurities clogged between the magnetic roller and the scraperThe toner leakage of the printer drum may also be caused by the blockage of large particles of impurities between the magnetic roller and the scraper, solution: We can try to disassemble the toner cartridge for inspection to remove the impurities. Mixing toner of different brands or qualities can easily cause waste toner residue and even cause large particles of impurities to clog! ​

Cleaned up, it may also be deformed.

Specific operation: Low coverage printing is more likely to cause excessive waste ton.

Method: Clean up the waste toner bin or switch to a toner cartridge suitable for low-coverage printing.

Deformation and breakage of the scraper blade caused by powdering.

Method: Re-open the toner cartridge and check the powder bin and scraper, or select a suitable alternative toner cartridge for adding powder.

There is a large particle of impurities between the magnetic roller and the scraper.

Methods: Disassemble the toner cartridge to inspect and remove impurities.

Disassembling the toner cartridge will destroy the sealing of the toner cartridge, and there will be leakage after the second installation of toner, and the leaked toner is easy to disperse into the air, which will affect the user's health after inhalation, and the leaked toner will cause irreparable damage to the printer, such as burning the motherboard or other components of the printer. Hardware problems caused by powder filling will not be warranted even during the warranty period, and the use of refilled old toner cartridges will cause the toner cartridge to not charge, which will affect the printing, and the quality is not guaranteed, so it is generally recommended that users do not refill the toner cartridge, and after the toner cartridge is used, directly purchase a new toner cartridge to replace it to achieve the best printing quality, if the above information does not solve your problem, you can continue to ask, or by visiting the HP technical support webpage (

The waste powder is not cleaned up, or the sleeves on both sides of the magnetic stick have fallen off. Then there is the sealing sponge on both sides that is misaligned or damaged when installing the magnetic stick.