How do you open a magnetic locking valve? How can a magnetic locking valve be opened without a key?

Updated on society 2024-07-13
12 answers
  1. Anonymous users2024-02-12

    Align the letter "C" on the key with the letter "C" on the magnetic lock cover and insert it into the lock. Then the corresponding magnetic bullet is fixedly mounted at one end near the key and the lock. The upper end of the stem on the valve body is provided with a rotary valve sleeve, which is consistent with the valve hole opened at the lower part of the lock.

    Gently press the magnetic lock with your hand, gently lift the magnetic lock, open the magnetic lock, and the valve switch can be operated. When closed, insert the magnetic lock directly into the valve.

    It consists of a spring, a lock and a valve body. The valve lock can be easily put over the valve, but it is not easy to remove. It is characterized by four spring holes equidistant at the side end of the lock, with a spring at the top against the magnetic spring.

  2. Anonymous users2024-02-11

    Place the key on the lock cover, make the small red dot on the key align with the small red dot on the lock, press a few times, the lock cover will pop out and be open, then pull out the lock cover by hand, move the valve stem with a wrench, adjust the pointer, point to 0-1 as shown on the indicator board, complete the closing adjustment of the corresponding process of opening, and then lock the valve so that the valve body is in a protected state.

    It is a kind of magnetic lock, which is generally used on some important, special position and functional valves to prevent the valve from being used by any switch, no gaps, no blockage, waterproof, anti-corrosion, and easy to use. It is favored by water supply, heating, gas and other industries.

  3. Anonymous users2024-02-10

    Definition. The so-called magnetic valve is a kind of magnetic lock that relies on the force of magnetic force to control the opening and closing of the closing parts in the control valve. It is generally used on some important, special position and function valves to prevent the valve from being used by arbitrary switches.

    There is no gap, anti-clogging, waterproof, anti-corrosion, easy to use; It is favored by water supply, heating, gas and other industries.

    How it works. It is composed of a spring, a lock, a valve body, the valve lock can be casually set on the valve, but can not be taken down casually, its characteristics are: 4 spring holes are arranged at equal distances at the side end of the lock, and there is a spring that supports the magnetic pneumator (ball) inside; The letter "C" on the key is aligned with the "C" on the magnetic lock cover and inserted into the lock, then the end of the key and the lock is fixed with the magnetic pneumator corresponding to the lock, and the upper end of the valve stem on the valve body is provided with a rotary valve sleeve that coincides with the valve hole opened at the bottom of the lock.

    Gently press the magnetic lock by hand, and the magnetic lock can be opened with a light lift, and then you can operate the opening and closing of the valve. When closing, simply insert the magnetic lock directly into the valve.

    There is no key to find two magnets to attract the magnetic beads on both sides to open.

  4. Anonymous users2024-02-09

    You can use a magnet to align with the mark, suck the steel ball inside, you can remove the pressure cap, how to open it inside to see.

  5. Anonymous users2024-02-08

    The magnetic locking valve can be opened without a key, and there are two main ways:

    Method 1: Use a magnet to move slightly along the top cover of the locking valve, cooperate with the stethoscope, and you will determine the position and number of his magnetic points, and mark them. Prepare the corresponding number of magnets and open them by pulling away the magnetic dots.

    Method 2: In fact, this is very simple, although it is called a locking valve, but the structural principle of the lock on this valve is very simple, that is, to change the shape of the valve stem.

  6. Anonymous users2024-02-07

    With a magnet, move slightly along the top cover of the locking valve, and cooperate with the stethoscope, you will determine the position and number of magnetic points and mark them. Prepare the corresponding number of magnets and open them by pulling away the magnetic dots.

    In fact, this is very simple, although it is called a locking valve, but the structural principle of the lock on this valve is very simple, that is, to change the shape of the valve stem.

  7. Anonymous users2024-02-06

    1. How to open the magnetic valve in front of the water meter.

    Open it with a strong magnetic key, align the letter "C" on the key with the "C" on the magnetic lock cover and insert it on the lock song, then the key and the lock are connected to the end of the fixed magnetic pneumator corresponding to the lock, and the upper end of the valve stem on the valve body is provided with a rotary valve sleeve that coincides with the valve hole opened at the lower part of the lock. Gently press the magnetic lock by hand, and the magnetic lock can be opened with a light lift, and then the valve can be opened and closed.

    2. Disturb the method before opening in an abnormal way.

    If you don't have a key or the key is not easy to use, it is recommended that you first find the distribution of the switch magnetic dots, which can also be opened, mainly in the following 5 ways:

    1. Use a magnet to move slightly along the top cover of the locking valve, and cooperate with the stethoscope to determine the position and number of his magnetic points, and mark them. Prepare the corresponding number of magnets and open them by pulling away the magnetic dots.

    2. If the key is gone, you can use a wrench or vice to clamp it and turn it. This is the stem protruding type, there is a valve stem is recessed, this kind of flathead screwdriver.

    3. There is no key to find two magnets to attract the magnetic beads on both sides to open.

    4. Please ask the locksmith to open the lock.

    5. Violent dismantling and direct prie-opening.

  8. Anonymous users2024-02-05

    Insert the key into the lock cover, align the red dot on the key with the small dot on the lock, press a few times, the lock cover pops out and is open, pull out the lock cover with your hand, move the valve stem with a wrench, adjust the pointer, point to 0-1, as shown on the indicator board, and then complete the corresponding closing adjustment of the opening process, and then lock it so that the valve body is in a protected state.

    This is a kind of magnetic lock, which is generally used on some important, special position and functional valves to prevent the valve from being used by any switch, no gaps, no blockage, waterproof, anti-corrosion, and easy to use. It is favored by water supply, heating, gas and other industries.

  9. Anonymous users2024-02-04

    The working principle of the magnetic locking valve is shown in the figure below:

    It is composed of a spring, a lock, and a valve body, and the valve lock can be set on the valve casually, but can not be taken down casually

    Four spring holes are arranged at equal intervals at the side end of the lock, and there are springs on top of the magnetic pin (ball), and the letter "c" is placed on the lock valve key"Align with the magnetic lock cover"c"Plugged into the lock, then the end of the lock valve key and the lock is fixed with the magnetic pneumator corresponding to the lock, and the upper end of the valve stem on the valve body is provided with a rotary valve sleeve that coincides with the valve hole opened at the lower part of the lock.

    Gently press the magnetic lock by hand, and the magnetic lock can be opened with a light lift, and then you can operate the opening and closing of the valve. When closing, simply insert the magnetic lock directly into the valve. Valve magnetic lock is a valve magnetic lock, which consists of a bonnet, a stem, a bonnet cap and a handle.

    There is a connecting device on the bonnet and the stem, the bonnet is provided with a steel pin groove, a magnet is placed at the bottom, the magnet is sleeved in the spring, the steel pin is placed on the spring, and the bonnet.

    The groove is provided on it, the handle is ring-shaped, there is no at least one pair of grooves and the corresponding bump on the outside of the bonnet cap and the handle, and the groove and the bump are consistent, and the opposite surface of the built-in magnet on the handle and the magnet in the steel pin groove is different magnetic poles. The valve magnetic lock has simple structure, reasonable design, convenient use, and effectively prevents abnormal opening and closing operation of the valve.

  10. Anonymous users2024-02-03

    The working principle and internal structure of the magnetic valve.

  11. Anonymous users2024-02-02

    On the lock cap of the key sleeve, the small red dot on the key is aligned with the small dot on the lock, gently press down a few times, the lock cap will pop up and be in the open state, pull out the lock cap with your hand, move the valve stem with a wrench, adjust the pointer, and point to the 0-1 shown on the indicator plate to complete the corresponding process of closing the adjustment and opening, and then lock it so that the valve body is in a protected state.

    It is a kind of magnetic lock, which is generally used in some important, special positions and functions of the valve to prevent the valve from being used by any switch, without any gap, anti-blockage, waterproof, anti-corrosion, easy to use, and is favored by water supply, heating, gas and other industries.

  12. Anonymous users2024-02-01

    How to open the magnetic lock of the valve.

Related questions
8 answers2024-07-13

Slotted locking valve, also known as magnetic locking valve, can not be opened without a key, is a valve specially produced for heating companies, which requires the use of a special key to open, and can also avoid the owner from opening the valve privately. >>>More

7 answers2024-07-13

What should I do if the keyboard key is locked.

36 answers2024-07-13

There is a portrait of a character in the upper left corner. There is a safety lock next to the head box, click to set. The default is unlocked 5 minutes after going online.

10 answers2024-07-13

1.If you set the pattern signature unlocking method, you can use the PIN code set when drawing the pattern signature. Operation: >>>More

11 answers2024-07-13

The high-pressure compressed natural gas comes out of the gas storage cylinder, and after being filtered by the natural gas filter, it enters the high-pressure pressure regulator through the high-pressure solenoid valve, and the opening and closing of the high-pressure solenoid valve is controlled by ECM, and the function of the high-pressure pressure reducer is to adjust the pressure to 7bar-9bar through decompression heating of the high-pressure compressed natural gas (working pressure 200bar-30bar). In order to prevent the pressure reducer from freezing, the engine coolant is drawn from the engine to the pressure reducer to heat the gas. The depressurized natural gas enters the electronically controlled pressure regulator, which is used to accurately control the amount of natural gas injection according to the operating conditions of the engine. >>>More