The toilet is displaced by 60 cm, and I don t want to raise the ground, how to solve it?

If there is no interior decoration downstairs, open a hole in the downstairs and renovate the sewer pipe in the ceiling under the floor as shown below, just pay attention to whether the hole is not broken floor heating pipe or wire casing, you can carry out renovation under the floor, but generally the owner of the downstairs may not be able to allow it! It is to discuss with the downstairs neighbors, because most of the people's toilet sewer pipes are downstairs! Naturally, if you are in the same floor of the drainage system, your own home is a sunken bathroom, you are even better "For various reasons, this method is generally difficult to achieve unless it is a villa" The application of the wall toilet again is not the harm of thin toilet spacing!

As long as it is at the same level as the sewer pipe, it is possible to raise the ground, but this method is not recommended unless it is a last resort.

Because it is not safe because the toilet shifter is a flat pipe, so open a groove in the ground, the spacing of centimeters, basically can be covered, it should be no problem, I used to do this, it does not affect the height of the ground! There are many new buildings of the toilet design scheme is a sunken toilet, for the owners of the community, the drainage modification of the sunken toilet is large, can be reasonable and reasonable layout of sanitary ware, washbasins, etc., but there are also shortcomings of the toilet is short. The working principle of wall drainage is that the sewer pipe receives the internal structure of the wall, connects it from the height of the centimeter above and below the ground, and then assembles the wall-type toilet to achieve the purpose of toilet displacement, which is consistent with the basic principle of raising the ground, but does not need to pull all the walls, only need to pull the sewer nozzle to the wall.

This method can achieve the purpose of relocating the toilet, and at the same time, it is possible to assemble a high-quality in-wall toilet, but because some parts move horizontally, the drainage will also be blocked, and the flow of water will be too slow. There is also a method of long-distance movement, because of the limitation of objectivity, it is not easy to be used often in home decoration, that is, to add new sewer pipes. The specific method is to communicate with the next-door neighbors, adjust the pipe arrangement on the top surface of their bathroom, and select the appropriate part to upgrade a group of toilet sewer pipes under the premise of the original sewer pipe, so as to achieve the effect of modifying the sewer pipe part of the roof toilet.

However, in the actual operation of the site, because of the inconvenience of communication, the neighbors next door are unwilling to wait, the use is relatively small, even if the agreement can be reached to carry out modifications, the construction of the project is not very good, and it will continue to cause moisture-proof leakage in the middle and later stages, and we do not recommend that the owners of the community do this.

Dig down: It is to warp off the floor tiles, dig down the original mortar layer and backfill layer, until you can pipe the groove again. This method is more expensive, because it will destroy the moisture at the same time as digging, so the moisture has to be redone, and then the bottom circle of the floor tile and wall tile has to be tiled again.

If none of the necessary conditions of the previous method can be met, then only a partial start will be done. It is to arrange the toilet in a reasonable manner, and move the toilet to an area that is conducive to starting the stage. Immediately pick up the open pipe on the top, and backfill the tile on the platform.

Without affecting the consequences of the application, it is best to be able to do part of the stage

You can renovate the original sewer pipe, install a toilet shifter, reopen a toilet hole in the ground, or change the drainage method and connect the pipes closely.

You can walk the tube directly, the ground should be about 20 cm high, or you can slot the ground to walk the tube, this effect is very good, and the ground does not need to be too high, and it will not have any relationship with people and idols, and it will be very convenient to use.

This problem can be solved by slotting the pipe in the ground and then reconnecting the sewage pipe.

1. Toilet shifter.

The toilet shifter is mainly aimed at adjusting the position of the toilet bowl in a small way, which is generally caused by the inappropriate distance of the toilet pit; However, the distance between the pits should not be too large, only within 10cm, and it will not work if there are more.

But there is a disadvantage of this is that once it is not handled well, it is easy to be clogged in the future, so it is recommended that you can not move it, after all, there will be trouble.

2. Change the sewer pipe.

This is also a solution, but it is necessary to negotiate with the residents downstairs when changing, otherwise it will cause neighborhood conflicts, and changing the sewer pipe is basically to make an elbow at the top of the downstairs to improve the blockage and avoid the problem of toilet shifters; However, after changing the position, remember that you need to redo the waterproofing, and the closed water test is indispensable to ensure that there will be no water leakage.

3. Change the shape of the toilet.

If the above two methods do not work, or the distance you want to change is too large, then you can find another way, just change the form of the toilet to a wall-mounted toilet, and such a change will look higher. It's just that the wall-hung toilet** will be higher, and you can decide according to your budget.

4. Displacement of sunken toilets.

It will be easier to move the sunken bathroom when decorating, because the pipes are buried inside, so even if you want to move, you only need to change the pipes inside, which is more convenient.

The traditional practice of toilet displacement is to transform the sewer pipe, connect a section of 110mm sewer pipe, and add a trap to prevent odor from flowing back, because the water pipe is thicker, so after the transformation, it is generally necessary to raise the ground by at least 12cm, if you do not want to raise the ground, then it is necessary to deal with it according to the specific situation. You can use a 75mm sewer pipe instead, the ground is slotted half, and the top is poured, but choose this method to displace, the distance should not exceed 1 meter, the water pipe becomes thinner, and you are afraid of blockage.

If you can negotiate with the residents downstairs, you can also re-drill the hole, and the displacement problem can be solved after the sewer pipe is renovated. This is the safest and most reliable way to move, but it requires communication with the residents downstairs.

The toilet shifter is shaped like two staggered elbows, but Mr. Xu told reporters that this toilet shifter is suitable for moving at a distance of 5 to 15cm, and the quality of the shifter is very critical when selecting.

The problem of toilet displacement mainly exists in the redecoration of some old houses and the decoration of some small apartments, and the industry reminds that it is necessary to be cautious when choosing the toilet displacement, especially the interface between the pipes, if it is not handled well, it is easy to cause leakage.

Hello, I sell toilets, my suggestion is, your home is equipped with a shifter, when installing the toilet, use 4 catties of white cement, 4 catties of 4 catties of water, 4 catties of cement, 1 catty of water, make the cement thick and mushy, the same as plasticine, just install the toilet.

There is no way but to raise the corresponding ground of the toilet.

Maybe when you install the shifter, you remove the cement on the outside of the sewer pipe and install the shifter relatively low.

The toilet shifter is raised above the ground. Normal because the ground has been tiled. The shifter itself has a height.

That must be on the ground. The toilet bowl cannot be installed, so it must be installed. The ground must be raised.

Or open a hole in the floor tiles. Put the shifter down. to install.

Bellamy's shifts are the best ones on the market right now. Good workmanship inside. Ultra-thin type, less digging depth, easy to install, not easy to block. You can check it out.

It is better to lower the floor than to raise the toilet.

I want to ask how to deal with it, mine is also 3 cm high.

The hole can be reopened, the toilet can be displaced, or the sewage pipe can be changed, and the problem can be solved, according to the specific design.

You can choose to slot the pipe in the ground, and start a pipe from 60 cm to this side.

You can choose a wall-hung toilet, so that you can solve the problem, to take measurements, choose according to your needs.

When you buy a new toilet, sometimes its drain may not match your spare parts. This may cause you to need to move the toilet to fit a different plumbing layout. However, when you move the toilet, you may find that the new installation location is uneven, and you don't want to make additional height changes to your floor.

Then in this case, you can try the following methods to solve the problem.

1.Determine where the toilet will be installed in the new place.

When you move the toilet from its original location to a new location, you need to first determine the new location you need. Make sure your new location fits your plumbing layout. This will help you move on to the next steps.

2.Use a padded board.

When you install a toilet in a new location, using a padded plate can solve the problem of floor height differences. A padded board is a rubber-like material that can be placed directly between the toilet bowl and the floor. It follows the height of the floor, keeping the toilet level while avoiding water leakage between the two points.

3.Use a rigid backing plate.

If your floor has a large elevation difference, using a rigid backing board can also be an effective solution. Unlike soft pads, hard pads are made of non-metallic materials such as polyethylene, which has good temperature and low temperature resistance, which makes it suitable for installation on the ground at different heights. The stiff plate will also not be compressed, which ensures that the toilet remains level during use.

4.Local materials.

If you're looking for an easy way to solve the problem of ground height differences, you can also use some local methods. For example, you can place some bricks or slabs on the ground to balance the toilet. However, the feasibility of this approach depends on the environment you are in and whether you have items available.

In short, the toilet displacement floor is not heightened, and it can also be solved by some simple measures. Whatever method you use, make sure your toilet remains level, which will prevent water from leaking during use while being safer.

You can choose a wall-hung toilet, which can solve the problem, it is more convenient to use, and there is no need to raise the ground.

You can redesign, you can choose to change the wall row, you can solve this problem very well, there is no need to raise the ground.

In fact, we can put a small stool under the toilet, which can also have the same effect, and when not in use, we can put the stool aside, which looks more beautiful.

Kiss is a pleasure to answer for you, my answer is <> below

How to move the toilet is not easy to block the ground and not highSome families need to move the toilet down because of decoration or other reasons, although it is only to move the lower position, but there are still many particulars, improper operation will be blocked, so before moving the toilet to understand what methods are available. 1. Toilet shifter. If the toilet position changes between 5-10cm, the most common is that the toilet position needs to be adjusted due to the unsuitable pit distance, and the toilet shifter can be used.

It is recommended not to use the shifter under extraordinary circumstances, although the product description can be moved by 5-10cm, but once it is moved more than 5cm, it will affect the flushing effect and easily block the toilet. If you want to move a longer distance, you can't use a shifter. 2. The floor is raised.

If the position of the toilet changes at about 10cm, beyond the range of the special toilet shifter, then the floor can be raised, and the horizontal pipe can be discharged in the raised part, and the distance between the toilet and the pit distance can be solved through the horizontal displacement of the horizontal pipe, and a water trap is also added to prevent the odor from flowing back. Since the diameter of the drain pipe is generally 11cm, it should be raised by at least 12cm to leave some room for the slope of the sewer pipe. Note that you should be careful not to turn between the newly connected pit pipe and the original pit pipe, otherwise the toilet paper is easy to block.

3. Install the wall-mounted water tank. If the range of toilet position changes is too large, you need to solve this problem by hanging a wall tank. However, it is necessary to buy the corresponding wall-mounted toilet, and the tiling of the water tank is relatively difficult, so it is necessary to consult the construction personnel in advance whether they are familiar with the assembly of the water tank and the external tiling process.

Of course, the clever use of the wall-mounted water tank can also directly connect the new pit pipe to the riser to solve the problem of displacement. 4. Re-hole the mobile toilet. Switch to a "rear-row" toilet (now generally a lower-row toilet).

In this way, the displaced pipes can travel along the wall, and it is easier to deal with the concealment of the pipes without raising the ground. Note: There is no technical problem with re-opening holes in the floor slab, but the consent of the residents downstairs is required.

This way it won't clog as easily as a toilet shifter. However, after changing the position of the sewer pipe, it is necessary to re-do the waterproofing and do a closed water test to ensure that there will be no water leakage. It is also generally suitable for small distance changes.

However, there are brackets and water tanks behind the wall-hung toilet, which need to be covered by a false wall, which will occupy a certain space in the bathroom, and the wall-hung toilet lid is more expensive.

When the toilet is displaced, it needs to be dealt with in time to avoid inconvenience to daily life. Here are the steps to deal with a toilet shift:

1.Check the cause.

Displacement can be caused by loose toilet screws, uneven floors, or aging seals at the bottom of the toilet. Before processing, the cause of the displacement needs to be checked.

2.Reinstall the toilet.

If the displacement is due to loose screws, you can use a wrench to tighten the screws. If the ground is uneven, it can be reinforced by laying cement or wooden planks on the ground. If it is a displacement caused by the aging of the sealing ring, the sealing ring needs to be replaced if it is resistant to bending.

3.Adjust the direction of drainage.

If the direction of drainage is not suitable after the toilet is displaced, it needs to be adjusted with an elbow to ensure smooth drainage.

4.Watch out for drain blockages.

After displacement, the drain may become clogged and the drain needs to be cleaned in a timely manner.

5.Fix the cracks in the floor tiles.

If the gap in the floor tile is large, it should be repaired in time. Because the gap is large and the floor is uneven, it will cause the toilet to shift.

6.Precautionary measures.

When installing the toilet in the future, Changyin should pay attention to choosing a sturdy bracket and sealing ring, as well as ensuring that the floor is flat. In normal use, also be careful not to jerk the flush button or sit on the lid of the water tank to avoid damage to the toilet.

In conclusion, dealing with the problem of toilet displacement requires promptness, patience and care, checking the cause, reinstalling the toilet, adjusting the direction of drainage, paying attention to blocked drains, repairing gaps in floor tiles and preventive measures are all necessary to pay attention to. With proper disposal, the inconvenience caused by the displacement of the toilet bowl to daily life can be avoided.