What should I do if the profile at the bottom of the broken bridge aluminum window that has just bee

Personally, I think that if the profile at the bottom of the broken bridge aluminum window that has just been installed begins to deform, it is likely to mean that the installation master has not installed it well, and it must be removed and installed again immediately.

You have to find someone who installed it for you at the time to remedy it, or find a professional person to renovate it.

I think you should go to the merchant, this kind of profile is not strong, there is a quality problem should go to him to change the new one.

Dear, hello, I am glad to answer the treatment method of the broken bridge aluminum window A: The treatment method of the broken bridge aluminum window falling is as follows: first remove the window leaves, and lock the upper part of the window frame with 10 cm Senxian steel nails to keep it straight, and then fine-tune the window leaves to make them at right angles, and then strengthen them with screws.

Due to loose hardware fasteners of the window sash or product quality problems, the window sash sags, and it is difficult to open and close the window sash. Such problems can be solved by tightening the sash hardware or replacing the quality of this leather problem fittings.

The side width of broken bridge aluminum doors and windows cannot be installed in reverse. Broken bridge aluminum alloy windows have positive and negative points, but when installed is not reversed, there are process requirements, installed reversed can not be used, you said that the glass has the inside and outside, should be the outside window, the outside window in the processing of a less conversion material, so that the glass strip on the outdoor side, there will be glass not on one surface.

Broken bridge aluminum alloy doors and windows benefitsBroken bridge aluminum alloy doors and windows have good tensile and deformation resistance, and are not subject to acid and alkali corrosion, there is no need to maintain it after installation, the performance is very good, its life is generally more than 50 years, and it is also a green building material, no harmful substances are produced during production, and all materials can be reused.

Broken bridge aluminum doors and windows, from its name you can know, it is an aluminum alloy material, it is very high because it penetrates the middle of the heat insulation strip, can effectively prevent the conduction of heat, compared with other aluminum alloy doors and windows, its thermal conductivity has been reduced by 40% to 70%, the performance has become so good, how can it not be high, and its advantages are not just thermal insulation.

How to repair the deformation of broken bridge aluminum alloy! Hello, I am glad to answer for you<> the repair method of aluminum alloy deformation of the broken bridge is as follows: the method of straightening the aluminum alloy bend:

1. Wear a square wooden strip in the inner cavity, which is required to be filled tightly, and then shape the bent buried aluminum square tube, so that it can be protected while returning to the front, and the outer surface folds can be welded and polished, and if there is spraying, it needs to be pretreated such as scraping; 2. If the bend is severe, you can try to cut it from the bend, shape and pack the port, and finally weld it. To reduce or avoid the scrapping of aluminum alloy due to bending, attention should be paid to three aspects: extrusion straightening, extrusion framing, and surface treatment on the shelf.

Selling shed ant extrusion straightening is a very serious bending of aluminum profiles, straightening must pay attention to the strength used in straightening, too much force may produce deformation, closing, orange peel on the profile, too small force will produce profile can not be straightened, resulting in bending. Extrusion framing is to frame after sawing the length of the fixed length, to figure out whether it is a large material or a small material, whether it is a material with a tube or a flat mold to pull out of the material, the material with a tube and the material with a tube is not easy to cause bending, but the material pulled out by the small material and the plane mold, it is easy to cause bending at both ends, at this time, it should be close to the middle from both ends to carry out the lifting and framing. If there is a large gap in the deformation and bending of the bottom profile of the broken bridge aluminum window, it can only be reduced by adding steel, aluminum flat through or U-channel steel, aluminum, etc.

Or make an L-shaped edge banding seam. 1.You can find someone to repair 2

See if it's not sealed, if the screws are loose, or something, just settle down yourself3Isn't it the strip that fell off or somethingIf it's a sliding window, the structure itself isn't sealed, just take things and race yourself, I hope mine can help you <>

Do you have any other questions?

Summary. It has no effect on use, and there is a high probability that it will leak.

First of all, the window is generally not oblique, it may be that you find a deviation from the wall with the naked eye, in this case, there is a problem with your door and window openings, and there is a deviation in the wall leveling.

Besides, if the lower window is really oblique, don't settle, re-install, the impact on the hardware is particularly prominent, especially the opening part, the deviation to 5mm to open the fan will be inflexible, falling corners, sinking and other situations, deviation of 5mm is too high there are potential safety hazards.

If the production process is reasonable, the gasket is placed in accordance with the standard, otherwise there is a risk of self-exposure of the glass under a long-term stress.

What is the impact of the broken bridge aluminum window installed crookedly.

There is no impact on the use, there is a high probability of water leakage, first of all, the window will not be oblique, it may be that you find a deviation from the wall with the naked eye, this situation is that there is a problem with your door and window openings, and there is a deviation in the wall leveling. Besides, if the lower window is really oblique, don't settle, re-install, the impact on the hardware is particularly prominent, especially the opening part, the deviation to 5mm to open the fan will be inflexible, falling corners, sinking and other situations, deviation of 5mm is too high there are potential safety hazards. If the production process is reasonable, the gasket is put in accordance with the standard, otherwise there is a risk of self-exposure to the glass for a long time.

The height deviation of the floor-to-ceiling window from left to right is centimeters, and now the tiles around the window are pasted, what should I do, and what will be the consequences in the later stage.

Let the master mend the sponge, otherwise it will seep water and leak in the later rain, and it will not be good to soak for a long time.

The window frames are tiled all around, and there is no way to repair the sponge.

Or you ask the master to write a lump note for you, if there is water seepage in the post-seepage period, fill and repair it for free, because the situation may be leaking now, but it is not clear how much is leaking, and it is not appropriate to make up too much and too little.

In addition to the phenomenon of water seepage, what will be the impact of the left and right height deviation of the broken bridge aluminum floor-to-ceiling window installation in the later stage.

Generally, it doesn't, it's mostly water seepage. Thank you.

Summary. Dear, I'm glad to answer for you, if the bottom of the bridge aluminum system window is deformed, it may be caused by the following reasons:1

Improper installation: Improper installation at the top of the bridge aluminum system window may cause deformation at the bottom. 2.

Temperature changes: Large-sized windows are exposed to sunlight, and temperature changes may cause deformation of the material. 3.

Poor material quality: If the material used in the bridge aluminum system window is of poor quality, it can also cause deformation. 4.

Mechanical changes over time: If the bridge aluminum system window is used for a long time, the bottom may also be deformed. 5.

Water infiltration: If the sealing of the bridge aluminum system window is not good, water may seep in, which may also cause deformation of the bottom.

The balcony is sealed at home.

The window frames have only been installed for six days.

These days to seal the glass.

When cleaning.

A side window frame was found to be deformed internally.

It's like being stepped on by someone.

Dear, I'm glad to answer for you, if the bottom of the bridge aluminum system window is deformed, it may be caused by the following reasons:1Improper installation:

Improper installation of the top of the bridge aluminum system window may cause deformation at the bottom. 2.Temperature Variation:

Large-sized windows are exposed to sunlight, and temperature changes can cause the material to deform. 3.Poor quality of materials:

If the material used in the bridge aluminum system window is poor, it may also cause deformation. 4.Rijiu Li Hui Yuanxue changes Wang dress:

If the bridge aluminum system window is used for a long time, the bottom may also be deformed. 5.Water seeps:

If the sealing of the bridge aluminum system window is not good, water may seep in, and it may also cause deformation of the bottom.

Kiss, you can go deep into the key to solving the problem from this aspect.