What should I do if the roof and wall peel fall off three months after the new house is renovated an

You should know that the main reason for the peeling off of the wall skin is that the putty powder is not done well, and the super glue is not enough, resulting in the weak adhesion of the wall. If it is a wall paint with good ductility, it is not easy to have this problem. But in the final analysis, it may be the problem of putty powder, if the putty powder is done well, no matter how the weather changes.

The walls are more likely to have some small cracks, and they are not easy to peel off and fall off. For such a thing, it is better to shovel off the putty powder and do it again. The main reason for the peeling off of the wall skin after decoration is that the paint brush at the bottom layer is too thick, which makes it very easy to molt and burst out, the bottom layer does not dry, causing the surface architectural paint to molt, the bottom floor of the house does not roll super glue, and the upstairs water seepage causes molting.

When something like this happens to be able to be repaired, it is advisable to shovel all of them, and it is more ideal to use a cement title page. The concrete floor slab in the room is made of frame formwork, binding steel bars, and pouring concrete.

In order to realize the separation between the template and the cement, and facilitate the removal of the board, a layer of release agent is generally brushed on the template. The existence of the template release agent is a serious harm to the bonding of the putty powder, therefore, most of the putty powder will fall off if the putty powder is not solved immediately if the release agent is not solved. Whether it is a new house or an old house, it is necessary to ensure that the roof is cleared and the construction is carried out, and only how to ensure that the decoration is not prone to problems.

If the original small white layer is not removed, the new small white putty construction is done on the top immediately, so that the adhesion between the new and old small white layer is very prone to problems, so that the new small white layer has problems peeling and falling off. The roof is all the lowest layer of paving wooden template, and then brush a layer of film release agent, which is conducive to the removal of the board after the completion of the cast-in-place concrete, so that the bottom end of the roof concrete is more smooth, and the putty powder is scraped on the cement roof in such a smooth and clean manner, resulting in the viscosity of the putty powder and the roof of the interior wall is weak, and it is very easy to fall off.

1. If the plastering surface is anti-sand, the reason is the ratio of sand and cement, and there is too much mud in the sand. The treatment is also very simple, shovel and re-brush, if you want to save effort, wash it with water, brush with glue or a layer of grout. 2.

If the wall is wet, the wall surface will come off. The wall should be treated with moisture in time. Solution:

Clean the peeling part of the surface, clean all the white parts, and fix the wall after the wall is dry. It is recommended that you paint the walls with high viscosity too white.

If you need to remove the wall skin and renovate it, you must contact the renovation company.

At this time, it is necessary to contact the decoration company, and it is necessary to re-decorate, and there are serious problems in the decoration.

If the wall is not sanded and leveled, the material behind it cannot achieve a more ideal decorative effect. Therefore, the program of wall sanding and leveling is very important. After polishing, the wall surface is smoother and more delicate, and the next step is the final procedure of wall decoration.

Determine whether it is the outside wall of the bathroom, if so, the reason is that the inside wall of the bathroom is not waterproof before the tiling, then it is necessary to achieve a waterproof height of two meters on the wall of the bathroom bathing area when newly renovated, and the rest of the area to be 30 cm.

The water vapor at the bottom layer is too large and does not dry thoroughly, or we brush the surface layer of latex paint after the putty is not dry, etc., the above situations will cause our wall skin to fall off. In this case, it is necessary to shovel off all the wall skin, shovel to the bottom of the wool wall, and then solve the cause of moisture. Wait for the wall to dry and then brush the wall.

Later, you can operate the process of latex paint.

The treatment method is not only to remove the white gypsum of the wall skin, etc., but also to remove the original ash layer, expose the brick wall and then re-plaster, and then carry out the interface agent, gypsum putty powder and other treatments after plastering. Shovel off the original putty on the wall, because the putty layer is relatively thin and not easy to shovel off, so it is more time-consuming to shovel the putty on the wall. After the putty is shoveled clean.

If the wall is removed too much, for example, it will leak directly through the concrete. Then the construction process is slightly more cumbersome. That's pretty much the way it works.

The wall skin peeling off area is small, you can first use a special tool to remove the peeling wall skin, and then use a brush to clean the wall, and then use a scraper to evenly brush the wall paste on the repair part, completely dry and then go to the second layer, and finally polish it, check the reason for the wall skin falling off, it may be because of the dampness caused by the environment, or it may be the top surface waterproof problem, so the cause should be found from the source, so it will be convenient to solve the problem in the later stage; Problems are most likely, and if there is a problem with these spaces, and there are problems with other spaces, it is advisable to consider the renovation as a whole.

You can shovel the area where the wall skin of the house has fallen off, and then reapply new paint, and then you should check the house in detail and the actual cause of the wall skin peeling. Some may be due to the dampness of the environment caused by the dampness of the wall skin, and some are due to the waterproof problem on the top surface caused by the wall skin falling off, and it will be more convenient to take appropriate measures to deal with it later after finding the reason.

You should first open the windows to ventilate the room, so that the temperature in the house becomes a little lower, so that adding some moisture will not be so easy to fall off the wall.

It should be solved by the developer, because it is a quality problem of the house, and the developer wants to solve it.

1. First remove the damaged and damp wall to the cement layer, clean up the dirt and dust on the construction surface, and keep it clean and dry.

2. Take out the wall repair set purchased from the online **, and communicate with the seller to purchase the coating suitable for your own wall.

3. Brush the cement surface 2 3 times with a separator, with an interval of about 3 hours between each pass, as shown in the figure below.

4. After drying the next day, use water-resistant putty paste to scrape the construction place, and after 4 6 hours of drying, polish the wall with sandpaper.

5. After the putty paste dries the next day, clean the surface dust and paint latex paint 2 3 times, with an interval of about 3 hours between each time.

If the wall is shelled, it is recommended to shovel it all, but a similar situation may occur after a simple repair. If you plan to shovel it off, the furniture underneath must be well shaded, and it is best to empty it, as there will be a lot of dust. It is still recommended to do wall paint on the top of the wall, and the corners of the wallpaper will still be easy to get up after a long time.

1. Remove the peeling wall skin first, and then scrape the putty again, and the areas with hollow drums and slight cracks also need to be peeled off and shoveled together, and the edges should be smoothed and scraped with putty, and then the primer should be painted.

2. The serious phenomenon of peeling may be that the base of the wall is not done, the wall skin peeling off the wall is removed to the wall base, repainted with a solid primer, whitewashed plaster leveling, pasting the mesh cloth, scraping the wall lining three times and then grinding and smoothing, and reinforcing the entire base layer.

3. If it is an ordinary fading problem, the way of rolling brush is used, and the roller brush topcoat will cover the part locally, and the primer and similar topcoat will be re-covered.

1. During the wall decoration construction, the base layer is not cleaned or improperly handled. 2. It may be that the quality of the prepared mortar and raw materials is not good. 3. It may be that the base layer is not properly painted, if the one-time plastering is too thick, the dry shrinkage rate of the wall will be larger.

4. It may be that the stirred mortar is not used in time, the parking time is too long, and the adhesion with the wall is not enough. 5. The skin of the living room wall falls off due to the humid weather. Suggested Treatment:

1. It is recommended to shovel off the place where the wall skin falls off, and then reapply the paint. 2. First shovel off the place where the wall skin falls off, and then see if there are loose, cracked, and hollow areas in other places around the wall, and it is best to shovel it out. 3. Check the reason for the peeling off of the wall skin, which may be due to the dampness caused by the environment, or it may be that the top surface waterproofing work is not done well, which should be found from the root cause to facilitate the solution of the problem in the later stage.

4. It may also be that the cement layer on the wall before scraping putty is unqualified, and the best way to solve the problem of wall peeling is to redo the whole wall. 5. Partial painting may cause a difference in color, at this time, you can choose to do wall painting or use green plants to block it. 6. It should be noted that the method and layer of painting should be the same as the previous wall decoration, and the wall should be dry during construction, and the same paint can be selected to apply, so as to ensure the adhesion between the paints.

Peeling on the wall is a very common phenomenon, which not only seriously affects the aesthetics of the house, but also has a great impact on our daily life. So, how should we deal with the newThe walls of the renovated house are peelingProcessing? What materials are better to use for wall decoration?

I'm going to give you a brief introduction.

1. Redo the wall.

If the peeling of the wall is more serious, it means that the wall base was not done well when it was renovated, and it is best to repaint the wall. The first thing is to remove the original wall surface until the wall base layer is exposed, and then repaint it with primer, level it with gypsum, and repaint the wall.

2. Remove the peeling place.

If the peeling of the wall is not particularly serious, you can also just remove the peeling place, the tool is a putty knife, and then use the purchased interface agent, use a small roller to roll the brush in the peeling place, and the wall will be flat after drying.

3. Make the first layer of the bottom.

If the peeling of the wall is not serious, you can also make the first layer of covering. Go to the market to buy white glue, add water to it, and add putty powder to it. On the coating of the interface agent, use a batch knife to get it, flatten it, and dry it, so that the wall surface is flat.

1. Diatom mud.

Diatom mud is very commonly used, and its main function is to regulate indoor temperature, purify the air, etc., which is more environmentally friendly. However, diatom mud is not waterproof, so it is more difficult to take care of it, so you have to be very careful.

2. Artificial jade slabs.

The advantages of artificial jade slabs are more prominent, the light transmission effect is good, the color difference is small, and the plasticity is also high, many families prefer it, and this material is not easy to fall off and not fragile after construction, which is easy for families to take care of.

3. Wood. Wood is also used in many homes because the wood decoration is beautiful, and the toughness and hardness are good. However, wood is more prone to deformation, and its service life may be shorter.

The above is Guan XinThe walls of the renovated house are peelingAs well as helpful when choosing wall decoration materials.

You can get it for free