My computer s hard drive is broken, I can t turn it on, can the files in the hard drive be recovered

Can be recovered, computer hard drive.

If it's broken, use the Universal Recovery Master.

1. Select Recover Data.

The solutions to the computer hard disk is broken and can't turn on are:

1. When encountering bad sectors that cannot enter the system desktop, we wait for 20 minutes at this time, because it may just enter normally, but our hard disk may be suddenly shut down last time to read and repair the hard disk data is not read, if you wait for about 20 minutes to enter the main interface of the system, it means that it has been repaired.

2. Of course, we can also enter the safe mode to set up, generally the computer can press F8 to open the system security mode to enter, in general, it is to enter the safe mode for system repair or restoration operations.

3、We enter a function called the last correct configuration,In the case of normal mode or safe mode,We press f8 to enter the page to select the last normal entry option to enter it,You can enter the time when there is no damage。

4. Hardware maintenance is required, of course, we do not rule out that it may be the bad track of the computer hard disk or the failure of other parts of the hard disk that causes the machine to fail, so we need to go to the computer repair shop for maintenance.

Causes of hard drive corruption:

1. Frequent abnormal shutdown, power failure, etc. will lead to bad blocks in the hard disk, and it is most likely to cause system failure after a sudden power failure, and the hard disk will be directly physically damaged.

2. The voltage is unstable, which is easy to cause physical bad sectors.

3. The damage of dust to the hard disk is very large, and it can be said that dust is the number one killer of the hard disk. As we all know, the contact between the head of the hard disk and the platter is very tight, and no dust is allowed, if the dust falls on the hard disk platter, then it is not too late to realize that the hard disk is from being damaged.

4. The circuit version on its back will also be damaged by static electricity. This is because when the climate is dry, the human body usually carries static electricity, in this case, touching the circuit board on the back of the hard disk with your hands, the human body static electricity may harm the electronic components on the hard disk, causing the hard disk to not function normally.

5. The hard disk will generate a certain amount of heat when it is working, and there is a heat dissipation problem in use. The temperature should be 20 25, too high or too low will change the clock frequency of the crystal oscillator. Temperature can also cause hard disk circuit components to malfunction, and magnetic media can cause recording errors due to thermal expansion effects.

Hello, if your computer's hard drive has been corrupted, resulting in a failure to boot or enter the system, you can consider the following steps:1Confirm if there is really something wrong with the hard drive:

Sometimes, the computer won't boot or enter the system not necessarily because of a problem with the hard drive. You can try to go into the BIOS to check the hardware settings or use the PE system for diagnostics. 2.

Replace the broken drive: If you confirm that the drive is damaged, you will need to replace it with a new one. If you don't know how to replace your hard drive, seek help from a professional.

3.Back up your data: If your hard drive is still readable, you can try backing up your important data to another device.

If it can't be read, you may need to seek a professional data recovery service. 4.Reinstall the operating system:

After replacing the hard drive with a new one, you will need to reinstall the operating system and other necessary software programs. Make sure you have the original installation media or the appropriate installation files. In short, when the computer hard disk is damaged, the most important thing is to protect your data, and replace the hard disk and reinstall the system in time.

It can be recovered, and if the computer hard drive is broken, you need to use the universal recovery master.

1. If the hard disk is only partially damaged by the circuit, after replacement, all the data can be recovered.

2. If it is caused by problems such as hard disk firmware, after repair, the data can be recovered.

3. If the hard disk platter is damaged and the head is damaged, you can open the disk to take the data and take out the undamaged part of the data. Of course, there is also the possibility that it cannot be recovered, and the cost is relatively high.

It can be recovered, but it requires a professional, and it costs money.

Small questions can't be said 100 replies to it, most files can still be replied to.

Change the hard disk, redo the system, and then use the bad hard disk as a slave disk, boot into the system.

lz first explains how it was broken, whether it was poisoned or physically damaged. The easiest way is to use Easy Recovery to recover your data, if not, you have to consider whether there are bad sectors in the hard drive. If you are poisoned, kill all the poison, if it doesn't work, take it to test whether there are bad sectors inside, if you find a professional repair hard disk to recover data, it is very expensive, generally around two or three hundred.

Reminder lz, if the data in the hard disk is successfully recovered, you can format the entire hard drive, maybe it will be easy to use.

1. Are you sure that the hard disk is causing the machine to turn on? If there is no motherboard information on boot, if there is nothing, check the memory, power supply and other components first. If it is stuck on the login screen, then it is considered a system and hard disk problem.

2. System problems from the system, if the hard disk can be identified on other machines, then directly back up the data in the format, it is generally caused by bad sectors. After the format is finished, it can be solved from the system, and only the bad sectors can be shielded for physical damage. If the plug-in can't be recognized, then go to a professional hard drive data recovery to recover the data, generally according to the importance of your data and the size of the hard disk.

Hundreds of small problems are solved.

Go to a professional data recovery company, almost 500 or so.

Whether it's a HDD or SSD.

Data recovery? Money ready to do more.

If the computer hard disk is broken and can't be turned on, you can directly replace it with a new hard disk, redo the system, and then you can turn it on.

To replace a hard disk, it is generally necessary to reinstall the system. If you don't have a system, you can't turn it on.

1. If the original hard disk is the only hard disk with a system, the system must be reinstalled after replacing the hard disk. Otherwise, it will definitely not turn on.

2. If the original hard disk is a secondary disk and the system is not installed, then it is possible that when it is booted, the new hard disk without a system is mistakenly regarded as the boot hard disk. In the BIOS, adjust the boot order of the hard drive.

3. If the system is installed with ghost, then it is likely that the main hard disk is not activated. Manual activation is sufficient.

3. If the system is installed with ghost, then it is likely that the main hard disk is not activated. Manual activation is sufficient.