-
Anonymous users2024-02-12It depends on what kind of lighting frame you are, generally they will provide a plan for the construction of the decoration industry, the construction mainly depends on the professional ability, if you do not have professional and technical personnel, it is recommended to invite professionals to come and install, after all, the installation also has an impact on the effect of the performance.
-
Anonymous users2024-02-11Didn't you buy their lighting stand and give you installation guidance to build? You can ask other manufacturers.
-
Anonymous users2024-02-10There are two connection methods for aluminum alloy light frame trusses, screw type and bolt type, but the steps of building and installing are almost the same.
Truss installation and construction tutorial - screw type.
1. Clean up the site according to the size of the installation required. If there is an uneven place, level it first, and do not have large trenches. Use a ruler to measure the position of the column and mark it.
2. Connect the base and the reverse head. I attach the reverse head frame to the base. Align the four holes, attach the screws, and tighten them with a special tool (Fig. 10).
3. Put the square sleeve into the reverse head (Fig. 11).
4. Place the set base on the fixed column. Adjust the base, adjust the screws, and level the base.
5. connecting the beam. First, connect the beams together to the desired length. (Figure 12).
6. After connecting, align the direction of the square sleeve and connect the beams to make the whole frame form on the ground.
7. Column connection. The length of the column is determined in the same way as the beam, and the cross arm is attached to the top of the column, and the cross bar of the hoist is hung in the direction of the cross arm facing the side with the length (Fig. 13).
8. Hang the gourd on the inner side of the column.
9. Install the column.
<>11. One person controls the locking rope, and the other several people push the column until it is straightened. Tighten the screws and the column will be in place. Repeat the above steps to complete the installation of all columns (Figure 15).
12. Put down the hook of the manual hoist or the hook of the electric hoist, pass the sling through the bottom to enclose the beam (Fig. 16), and hook the ring on the sling on the hook.
13. One person pulls the hoist up at the same time for each column of the manual hoist (the electric hoist is energized at the same time and rises synchronously).Note that the rising speed of each point should be consistent and rise steadily.
14. Stop when rising to about 1 meter, install the diagonal brace rod on the column, and level the base. Wall Chart 16 Figure 17
Put on the lamp and connect the cable. Once you have hung the fixtures or exhibits, repeat step 14 until you reach the desired height. After reaching the height, check whether each adjustment base is on the ground and leveled. Fix the zipper of the hoist and it's done.
15. When dismantling the rack, it is just the opposite of the rack.
Safety first, don't be overweight or overweight!
-
Anonymous users2024-02-09**Net, you can definitely find it.
It is recommended that qualified families do not use aluminum cookware, except for iron pots and casseroles, all stainless steel cookware are used. Because stainless steel products have stable metal properties and are harmless to the human body. 】 >>>More
Aluminum profile protective door is used for safety protection around all kinds of automated production equipment, robots, punches and other equipment in the factory workshop. In some areas, doors or passages will be installed to facilitate the entry and exit of goods and personnel maintenance. Aluminum profile protective door can not only be customized according to the needs of the site, but also due to the diversity of industrial aluminum profile varieties and connection methods. >>>More
1. In terms of the way of purchasing cabinets, nearly 7 percent of the respondents said that they would buy the whole cabinet by themselves, followed by the purchase of finished cabinets, and only 7% chose the original cabinets of hardcover houses. The data shows that at present, the concept of the whole cabinet has been deeply rooted in the hearts of the people, and consumers realize that the whole cabinet will take the initiative to choose the whole cabinet in meeting the personalized needs. The data also shows from the side that the overall penetration rate of hardcover houses is still not high, and cabinet companies are still dominated by traditional dealers, stores and other retail channels in terms of channel development. >>>More
1. The surface of the profile of the aluminum alloy swing door in the bathroom is made of wood grain transfer, electrophoretic coating, spraying and other processes, the texture is clear and delicate, the three-dimensional sense of hierarchy is strong, and the surface is very smooth and natural after repeated polishing. >>>More
The composition of the aluminum alloy (both referring to the mass fraction) has a great influence on the appearance, thickness and compactness of the film. The film layer of pure aluminum is transparent, glossy, thick and dense. For aluminum-magnesium alloy, when the magnesium content is lower than 3 in the form of solid solution, it has little effect on the quality of the film, and when its content is higher than 3, the alloy has the second phase of MG5A18 precipitation. >>>More