The installation method of the sliding window diamond mesh screen

The installation method and skills of the screen window are as follows:1. When installing the screen window, first pad the bottom, install the screen slot and air groove, and combine them into a square frame, and then reinforce it with screws, pay attention to nail the screws tightly to prevent them from loosening.

2. After installing the frame, you can fix the finished screen, note that the general screen window will choose a slightly larger one, so as to facilitate the installation or future cleaning of the disassembly, pay attention to the symmetrical air groove and the window margin during installation, to avoid the damage to the external window caused by the sliding and window cleaning caused by poor installation.

3. It should be noted that the bottom of the mat is generally about 5 cm lower than the spacing of the window frame, and then use clips to fix the rest of the directions to prevent the window from moving back and forth.

Step 1: Before dismantling the diamond mesh screen, be sure to observe the type of hinge to see if there is a shaft rod that can be removed.

Step 2: If the hinge has a shaft rod, then you can open the diamond to make a mesh screen, which is about 45 degrees angle. Hold the frame of the screen with both hands.

Push the hinge up hard, push out the shaft rod of the hinge, and pay attention not to use brute force when removing the diamond mesh screen, and find a good position, so that the diamond mesh screen will be removed.

Step 3: If the hinge does not have a shaft rod that can be directly removed, you need to use the corresponding screwdriver to rotate the screw out, and you must pay attention to the safety of use, so as not to scratch your hands. Remove the hinge so that the diamond mesh screen is removed.

Cleaning and maintenance of diamond screens:

1. It is necessary to check the joint between the diamond mesh frame and the wall of the diamond mesh screen window, because there will be loosening with the growth of use time, which is easy to deform the frame as a whole and make the diamond mesh unable to close and seal. So, if you notice that the screws are loose, they should be tightened immediately.

2. After the screen is installed, regular maintenance should be carried out, and the screen itself also has an automatic cleaning function to roughly remove the dirt on the surface, and clean it by itself at the same time.

3. The regular maintenance of the screen window is also very simple, spray some lubricant on the screen track, lubricate the track, and add some oil to the positioner. If the yarn surface is damaged, the yarn surface can be replaced, which is flexible and easy to maintain.

4. If you need to clean foreign objects and dirty spots on the diamond screen, do not use steel wool, steel brushes and other metal objects to clean the screen, and use newspapers, water, sponges, etc. to clean the screen.

5. The diamond mesh screen window can be disassembled, and the handle lock, hinge shaft, and clutch lock connection can not be directly soaked with water during cleaning and maintenance, so as not to cause rust in the accessories and the failure of the switch, and regularly inject a small amount of hydraulic oil into the connection of the hardware and nuclear parts, which can alleviate the wear and tear of the hardware accessories and extend the service life of the product.

6. If the diamond screen window is rusted due to oxidation, the rust can be gently scraped off with a knife, then washed with soapy water, wiped dry with a dry cloth, and then wiped with a dry cloth after waxing oil, which can be smoother as new.

Diamond mesh screen installation tutorial: The first step: assemble the lead yarn box, air groove, and bottom of the pad, and then screw it on with six screws to make it a square frame.

Step 2: Place the screen window in the installation site, pay attention to the left and right air grooves and the margins of the door and window frames should be symmetrical, and the bottom position should be about 5cm lower than the frame of the door and window frame. Step 3:

Use an electric drill with a drill bit to drill holes in the inner strips of the door and window frames. Step 4: According to the need, press the draft at the corresponding place of the left and right air grooves and the bottom of the pad to open 6 to 14 eyes, and then screw the screws to complete the installation.

Dear, I'm glad to answer for you: How to change the screen of the diamond mesh screen: 1. First of all, we need to determine what our windows look like.

Because some windows are inward or outward, and some are casement windows, it is not the same when installing diamond screens. 2. When installing, you need to paste the magnetic stripe of the diamond mesh on the edge of the window, and you can't paste it at will, the two sides should be aligned, and you can't tilt or fold it, and then use a pair of scissors to cut off the excess part from top to bottom, and keep a little length. 3. Next, the paper on the diamond mesh strip should be removed, and the plastic strip should be pasted on the connecting net of the magnetic stripe, and it should be pressed firmly and tightly connected together, so as to increase the adhesion.

4. Wait for a few seconds before removing the top strip, then paste it on the window, and then press it with your hand to increase its adhesion. Note: Before installation, you need to measure the size of the window, and install it according to the size.

If there is excess, it must be buried in Zheng to pay attention to the wheel cutting according to the size of the window, but it can not be cut directly, it must be fixed after the wax liquid can be cut, so that the sub-size will be more accurate.

The steps to remove the diamond mesh screen are as follows:Tool: Diamond mesh screen.

1. Check whether the keyhole of the diamond mesh screen window is locked, horizontally it is locked, and vertically it is open.

2. Insert the key, rotate it up to the vertical direction, and open the diamond net lock.

3. Palm up with one hand, reach into the gripper, lift up slightly hard, and after hearing the sound of leaving the window frame, hold the screen with the other hand to remove the diamond mesh screen.

Tips for choosing diamond mesh screens1. Look at the thickness of the profile.

Usually the thickness of the diamond mesh is, the thicker the better. The thinner the profile, the more brittle and louder the sound of the diamond mesh when it is struck by hand, the weight will be much lighter, and it will not be natural and durable.

2. Look at the material of the diamond net.

The screen of the diamond screen is different, and its core is the diamond screen. The real diamond mesh is made of 304 or 316 stainless steel, but some small screen manufacturers use iron sprayed gauze or 201 mesh and manganese steel mesh in order to compete with small brands, which are easy to corrode and rust, and the service life is not long, and the cost is nearly 80% cheaper than that of 304 stainless steel.

Diamond mesh screens are made of special profiles and special machines, most of the operations are completed by machines, and tightening the mesh requires a special structure and special process, and there is no way to tighten it manually.

The anti-theft screen is made of high-strength stainless steel wire, and the surface can resist the damage of various severe weather or environmental corrosion factors such as acid rain for a long time after electrophoretic spraying.

It is made of special material, which is convenient for care, and with a little care, it is as bright as new, and the life span is 10 times that of ordinary screens.

Hello, Qiangning anti-theft window for you to answer, diamond mesh screen windows are made of special profiles and special machines, most of the operations are completed by machines, and tightening the mesh sheet requires a special structure and special process.

Excuse me, how to tighten the diamond yarn?