Can the wire installation be connected to the network cable? What are the points to pay attention to

Generally, it should be separated, not in a tube, so that it is easier to interfere with the crosstalk. Points to note:1

When we install wires, we must know the color and performance of the wires. We can't afford to make any mistakes during the installation process. 2.

It is very dangerous if the wires are reversed. When installing the wire, the insulation of the wire end must be stripped off, the core of the wire must be wiped clean, and then soldered. 3。

In the process of installing wires, be sure to do a good job of anti-electricity. It is best to wear insulated gloves when touching wires. Not only that, but all the power in the home must be turned off.

Of course not, as this may affect each other and may cause the power supply to be stressed. It should be noted that it cannot be installed in the same pipe, but also pay attention to the distance, but also pay attention to the way of installation, but also pay attention to the protection of the wall, but also pay attention to the stability of the voltage.

Under normal circumstances, they can not be together, it is easy to affect each other, and we must pay attention to the laying of pipes and the problem of load-bearing walls when decorating.

Hazards if the power cord and the network cable are threaded through the same pipe:

1. The weak current signal is transmitted in the network cable, and the strong current is transmitted in the power cable.

When the strong current passes through the wire, a magnetic field will be generated, and the magnetic field will interfere with the weak current signal of the network cable, resulting in abnormal network cable signal, which will seriously affect the normal communication of the network cable.

2. There are potential safety hazards.

If the power cable and network cable are damaged, the copper cores of the two cables collide together.

If a strong current is connected to the network cable, it will cause the connected computer and other equipment to burn out. Serious ones will lead to disasters.

Ethernet cables and wires can't go through a tube.

The network cable is used to transmit network signals, so it cannot work under a relatively large magnetic field interference. If the magnetic field of the environment it is in is too large, it will affect the transmission of network signals. When the wire is transmitted, it will generate a magnetic field, which will affect the transmission of network signals, so it is not possible to pass the network cable and the wire through a tube.

Because the network cable is mainly transmitted by optical fiber, it is very fragile, can not be folded, and is easy to be damaged.

From the safety point of view, if the outer package of the wire and the network cable is damaged, the copper core inside the wire will be exposed, if the two copper cores touch together, it is more dangerous, and there may be a fire, so the network cable and the wire can not go through a tube.

Considerations for network cable and wire location planning:

1. The network cable and the wire can not be too close to each other when the position is arranged, the wire will pass through the current when transmitting, and the current will produce a magnetic field, which will affect the transmission of the network signal, and the network signal of the network cable will be affected at this time, and the network effect will be bad.

2. The network cable is fragile and afraid of folding, so try to fix the network cable in a place that is not easy to be touched when planning, so that it will not affect the network effect.

3. The wire is more prone to danger, especially when the insulator wrapped outside is damaged, it is more likely to be at risk of electric shock, so the wire needs to be placed in some hidden places near the wall, and it also needs to be fixed.

The arrangement of indoor wires and network cables is a very important link, if there is a problem with the typesetting, the later use will be affected, and it will become very troublesome to re-wiring. So can the network cable and the wire go through a tube, and what need to be paid attention to when installing the network cable, do you understand? Now let's take a look.

1. Can the network cable and the wire go through one tube?

No, it is not possible to distribute network cables and wires in the same pipe. The wires used in our homes are all with strong current, only the network cable is weak current, when the two are in the same tube, it will lead to poor transmission signal, and even the network cable can not be used normally.

2. What do you need to pay attention to when installing network cables?

1. In the process of daily pipeline installation, it is necessary to do it in strict accordance with the standards stipulated by the state. When arranging the wires and network cables in the room, it is necessary to make two conduits, pass through the wires and network cables respectively, and then separate the two pipes by a certain distance, almost on the left and right, so as to avoid interference.

2. When wiring, don't be too nervous. Although the distance between the wire and the network cable should not be too close to prevent the interference of the magnetic field and the inability of the line to be used normally, it is necessary to know that the shell of the wire belongs to the insulation layer and has the effect of reducing the strength of the magnetic field, so as long as the wire shell is not damaged, the impact is not large.

3. Before the interior decoration wires and network cables, it is necessary to go to the building materials market in person to select the corresponding materials, which not only requires high environmental performance of the materials, but also has good quality of materials, so that the line can be used for a long time, and at the same time, it is not easy to be damaged, which brings convenience to home life.

About whether the network cable and the wire can go through a tube, and what you need to pay attention to when installing the network cable, I will introduce it here, do you understand? The network cable cannot be arranged together with the wire, otherwise it is easy to interfere with each other, resulting in the normal use in the later stage, and it will become more troublesome to repair it again.

In the process of decoration, the safety of the owner has always been a topic of concern, and the safety of the circuit decoration is a very important part of the whole decoration process, and the quality of the circuit decoration will directly affect the safety of the owner in the future. When decorating the circuit, the wires used will be threaded, so do the decoration wires have to be threaded? How many wires can a pipe wear?

Let's take you to know it in detail.

1. Do you have to wear pipes for decoration wires?

We know that the main purpose of the wire pipe is to protect the wire and avoid the problem of broken skin of the wire, which leads to potential safety hazards.

1. Ensure the safety of wiring and discharging.

The wire guarantee protects the wire, and also avoids the direct exposure of the wire to the air, preventing the risk of electric shock in the process of work. In this way, even if the wire is accidentally pulled or damaged while discharging the wire, there is no danger.

2. Prevent damage to the wire insulation layer.

Wires are usually buried underneath sand and concrete, and are susceptible to corrosion. At this time, the wire wrapping is very important, and the outer bread of the wire can largely prevent the insulation of the wire from being damaged and reduce the risk of short circuit.

3. Prevent fire.

Once the wire inside is caught on fire due to a short circuit, the guarantee can prevent the fire from deteriorating further, prevent the flame from spreading to other flammable or explosive items, causing greater loss of property and personal safety.

4. It is convenient to replace the wire.

A good guarantee not only protects the wire, but also makes it convenient to pull the wire at will. This makes it easy to replace the wires in the event of a line failure in the future. There is no need to open the entire wall or ground, and then take out the wires for repair, only need to pull the broken part of the wires out of the package to change the calendar, which is convenient and practical.

5. Help dissipate heat.

Wires often generate heat due to overwork. If it is buried directly in concrete and there is no circulating air circulating around the wire, it is likely to be dangerous due to overheating. After the wire is wrapped, there will be space for air flow around the wire, which can help with heat dissipation.

Second, one pipe can thread several wires.

How many wires can a tube wear? It is not more than 6, according to the national standards, the total space of the wire in the PVC pipe shall not exceed 40%, converted into popular, like the home decoration of the conduit is generally used 16mm, if you wear a square wire, you can only wear about 6, if it is a 4 square wire, you can only wear 3. This only needs to be calculated according to the cross-sectional area of the wire.

The network cable and the wire cannot pass through the same pipe, because the network cable transmits a weak current signal, while the power cable transmits a strong current. Due to the principle of electromagnetic induction, a magnetic field is generated when a strong current passes through the wire, and the magnetic field will affect the weak current signal of the network cable. Interference causes abnormal network cable signals, which will seriously affect the normal communication of network cables.

In addition, if the power and network cables are damaged, the copper core sources of the two cables will come into contact with each other. If a strong current enters the network cable, it will cause the connected computer and other equipment to burn or cause electric shock to the human body, and even cause a disaster in serious cases.

The decoration circuit diagram must be kept, because the circuit wiring diagram is the circuit design and construction drawing left to the owner by the construction party after the construction is completed, which can be used as a reference for future inspection and maintenance. When decorating, water pipes, electrical wiring, ** lines, cable TV lines, etc., are generally either buried under the floor or buried in the wall, covered with cement, and then decorated on the surface. This fully enclosed method has caused many safety hazards and also brought great obstacles to the maintenance of pipelines in the future.

Therefore, keeping a complete pipeline roadmap is a prerequisite for avoiding problems and solving them in the future, otherwise there is no way to start.

1.Be careful not to have too many connectors on the line. If the wiring, insulation, moisture-proof and other aspects of the connector are not properly handled in the laying of the circuit, open circuits and short circuits will occur.

Therefore, during the construction process, line joints should be minimized. If you need to wiring, you should be careful, the wiring circuit should be connected, do a good job of moisture-proof insulation, and you can also use terminals. For the coaxial cable connection of the TV antenna, it is recommended to use a splitter or junction box.

2.Note that the shell of the processing line is hidden. When concealing the line, it is necessary to protect the line with a sleeve to avoid damage.

3.The selection of wires should be reasonable. Different rated currents match wires of different specifications, and choosing the wrong wire may cause long-term overload of the line and bury potential safety hazards.

Generally speaking, the lighting line is square millimeter, the general socket line is square millimeter, the high-power socket wire such as air conditioning needs 4-6 square millimeters, and the household wire is 10 square millimeters.

4.Strong and weak current cannot be in the same slot. Strong and weak currents must be routed separately, especially not in the same slot at the same time.

In order to facilitate later judgment, it is necessary to distinguish the color of the strong and weak wire pipes, red strong current, blue weak current, do not confuse. When wiring, it is best to follow the principle of strong current and weak current.