Can I still apply tiles after brushing the wall reinforcement?

It is still possible to paste tiles, and the wall can be brushed with cement grout to make the wall rough. Late tiling can increase friction.

First, the role of wall reinforcing agents

Walls can be said to be a particularly important part of the renovation process. Poor wall decoration will affect the whole room. Nowadays, many people will brush a layer of wall reinforcement on the wall when decorating, and its function is to make cement mortar through the wall reinforcement.

becomes more cohesive if waterproof coatings are used.

After drying, the entire wall becomes seamless and prevents water leakage. Increase the fastness to the plaster or putty required for wall leveling in the later stage, so that the wall painting is more uniform and durable. <>

Second, the use of wall reinforcement and main matters

Most wall decoration is the use of cement grout, so you must check it before construction, for example, to see if the wall is smooth and firm, if it does not meet the standard, change it immediately. After painting, wait about 30 minutes and press the wall with the palm of your hand to see if there is any sticking hand. If not, it proves that the reinforcement treatment of the wall base layer is completed, and then scrape the putty after the treatment.

On the wall, the wall can be made firmer, and the putty scraping effect is better. <>

Third, how to choose tiles

Ceramic tile is one of the most commonly used decoration materials in us, and it is also one of the essential materials. The following will explain to you how to choose tiles, the first thing to check is whether the color of the tile is pure. This trick is very simple, mainly to observe whether the color of the back of the tile is uniform and consistent.

Good quality ceramic tiles, green body color system.

1. Symmetry. Second, it is necessary to observe whether the particles of the cross-section of the tile are fine. Note that the cross-section here does not refer to the cutting surface around the tile, but to the tile fragments.

of the fracture. Generally speaking, the fracture is fine, hard and brittle, and the color is the same. Because the fine particles of ceramic tiles have strong waterproof ability; The ceramic tiles with larger particles are easy to soak in moisture and affect the quality.

Fourth, tap on the tiles and pay attention to whether the sound is crisp. If the voice is clear and pleasant, it is the top grade, and if the voice is dull, it is the inferior <>

No, because it will encounter a certain impact when pasting tiles, and if it is not tightly attached, it is easy to fall off in the later stage.

OK. But you need to scrape off some of this layer before you can stick it, so that it will stick a little firmer, otherwise it will not stick.

At this time, you can't put tiles, because the wall is very smooth with reinforcing agent, and it is difficult to glue the wall on.

Brush the wall solid. After that, you can't directly paste the tile, because it is easy to fall, and you need to do a good job of waterproofing and brushing before you can paste the tile. After waterproofing, you must do brushing, otherwise the tile will not be firmly pasted, and it will fall down after a long time.

The drying time of the wall solid is very fast, and the high-quality wall solid can be constructed today and the next day. And when tiling must be rigorous and standardized, the specific operation methods are: 1. Leveling; 2. pulling the wire; 3. Soaking in water; 4. mixing slurry; 5. paving; 6. Inspection and seams; These are all indispensable steps that can prevent hollowing out in the future.

The case of falling off.

Brush the wall reinforcement can be tiled. Wall reinforcer, as the name suggests, is to reinforce the wall, and you can brush the wall reinforcing agent and then paste the tile.

Many people are very interested in home decoration, because clothing, food, housing, transportation and housing are in the first place, and many people want to have a very good environment to live, so they want to learn the relevant knowledge of house decoration. Wall reinforcer, many people will use this material when decorating, some people think that the wall reinforcing agent is to strengthen the wall, so the wall reinforcing agent can be pasted tiles. Because the wall reinforcing agent can make the wall more compact, and the cement is more adsorption, it is okay to paste tiles after brushing the wall reinforcing agent.

Wall reinforcing agent can better strengthen the wall, you can first brush the wall reinforcing agent, then brush other paints, paste wallpaper, etc. The purpose of this is to make the wallpaper and these paints better integrated with the wall. If there is no reinforcing agent on the wall during the decoration, and there are problems such as sanding on the wall, it is likely that the decoration materials and the wall will be separated, and the wallpaper will be layered and fall off.

Therefore, brushing a layer of wall reinforcing agent on this bad wall can make the wall and paint, wallpaper and other materials fit more closely. If the wall needs to be tiled, it is best to brush a layer of wall reinforcement, which will make the wall tiles more solid.

Many people are curious, after brushing the wall reinforcement, can you immediately paste the tiles? This is not possible, because after brushing the wall reinforcement, you will immediately go to paste the tiles, and the tiles may not be pasted. Wait for the wall reinforcement to dry before you can apply tiles.

If the walls of your home are better, the wall reinforcing agent will dry faster, and you can apply tiles by the second day. If your walls are a little worse, wait a little longer until the wall reinforcement and wall fit tightly together before sticking the tiles.

It's still possible. But you still need to wait for a while when posting, so that the effect of posting may be better.

You can also paste tiles, as long as you stick them firmly, this is no problem.

As far as I know, the wall reinforcement can be applied to the tiles, and it is more durable, moisture-proof and not easy to fall off.

1.There is no problem with tiles sticking to the wall, because the function of the wall is to help the cement wall to reinforce the loose particles, it will strengthen its tightness, so that the wall can be sealed. Improving the wall can make the decorative materials and the wall more closely combined, and at the same time can prevent the wall from being damp and whitening afterwards, so there is no problem with tiling on the wall.

of attachment. When using solid walls, be sure to add water to the warehouse and dilute it at 50% to 100%. When the position is stable, you must pay attention to the strength of the force.

2.Confirm the pattern of the bricks according to the relevant requirements, pull the marking line on the surface that looks dry, and then completely place the wall tiles in clean water, which usually takes 30 minutes. The specific soaking time is subject to the fact that the tiles do not bubble, and then take out to dry the water stains for later use.

inspection and engagement; These are all indispensable steps that can prevent hollowing and falling out later to a certain extent. When paving, spray enough water on the wall, gently tap it with a wooden pestle to make it smooth, and then level it with a level; After the tile is paved, check the hollowing of the tile.

3.It can be inspected by tapping the brick surface with the wooden handle of a small spatula. If the sound is "knocking", it means that the tiles have been hollowed out.

It is advisable to immediately remove the hollowed-out tiles and re-lay them. The general process is that after waterproofing, it must be brushed, otherwise the tiles will not stick firmly and will fall off after a long time. It is said that the use of tile binder instead of cement mortar, the so-called new thin paste method, does not require brushing, which is not true.

The construction practice is: whether it is the new thin paste method or the traditional paving method, the wall needs to be treated with a base layer and brushed first.

4.Before tiling, it is necessary to hang a horizontal line on the wall, so that the process of tiling can be more smooth, to achieve the effect of horizontal and vertical, to ensure the overall aesthetic effect. In addition, during the processing of ordinary ceramic tiles, it is necessary to set up a support plate on the basis of the horizontal line to prevent the tiles from falling off.

If you want to wrap the sewer pipe with floor tiles, you must wrap it for a long time before you can paste the tiles, and add soundproof cotton to the pipe, which can better block the noise and ensure sufficient beauty. If the exterior wall of the balcony is tiled, a layer of mud should be brushed on the wall base to ensure that it can be pasted more firmly.

OK. If you use a reinforcing agent when painting the wall, and then paste the tile, it is also okay to make the wall more stable, and then pay attention to choosing some environmentally friendly materials and glue.

You can also continue to paste tiles, and you must use a tile adhesive to glue firmly when you apply tiles, so that it is the best.

Of course, when pasting porcelain, you can brush the tile adhesive, which will be stronger and not easy to fall off.

Summary. Hello, I am glad to answer for you, before pasting wall tiles, you need to brush the wall solid. Brushing the wall can lay a good foundation for the wall, especially when the wall has a large area of sand, depowdering and other phenomena, brush a layer of strong, and then paste the brick, it will be more firm.

If there is no problem with the wall, you can also directly paste the wall tiles, and it is not said that the wall must be brushed before tiling. However, it is recommended to paint a layer of wall solid before tiling.

Hello, I have seen your question, and I am sorting out the answer, please wait for a while. Brushing the wall can lay a good foundation for the wall, especially when the wall has a large area of sand, depowdering and other phenomena, brush a layer of strong, and then paste the brick, it will be more firm. If there is no problem with the wall, you can also directly paste the wall tiles, and it is not said that the wall must be brushed before tiling.

However, it is recommended to paint a layer of wall solid before tiling.

I hope the above helps you If you are satisfied with me, please give a thumbs up <>

Hello dear, I have helped you find the result; Wall tiles generally do not need to be brushed. Before attaching wall tiles, it is usually necessary to carry out wall treatment first, including putty, leveling, sanding and other steps to ensure that the wall surface is smooth and smooth. After these steps are completed, there is generally no need to repaint the wall.

Wall solidification is a chemical used to cure walls, which can improve the hardness and water resistance of the wall, and prevent problems such as cracking and sanding on the wall. However, if the wall solid is used before the wall tiles are applied, it may affect the bonding effect of the bricks to the wall, resulting in the brick surface being easy to fall off. Therefore, it is recommended not to use wall solidification before pasting wall tiles, but to choose the appropriate brick glue for construction according to the wall situation.

In the process of imitating the virtual collision work, attention should be paid to controlling the thickness and uniformity of the brick glue to ensure that the bond between the brick and the wall is firm.

Wall solid is an efficient interface treatment material to prevent hollowing and sand after tiling.

In fact, the wall is not necessarily used, and the main reason for tiling is to strictly use the cement number in the building code and the ratio of cement mortar. It can also be very good to do tiling without hollowing and sand.

Summary. It is better not to use the reinforcing agent to stick the tiles, mainly to strengthen the wall. Reinforcing agent is the latest generation of wall curing agent wall sealing curing treatment products, with nano-scale polymer polymer emulsion as the base material and environmental protection additives reaction polymerization polymerization, absolutely free of formaldehyde, benzene and other toxic and harmful substances completely green environmental protection.

The unique super physical permeability can penetrate deep into the wall, and the excellent bonding strength, crack resistance and good alkali, moisture and mildew resistance after curing of the product can make the surface layer of the cement wall or plastering wall and the internal fine loose place completely bonded and dense to improve the overall strength of the wall, effectively improve the bonding strength and adhesion of the wall putty batch coating and tile paste base, and is a supporting product for the reinforcement treatment of the home decoration wall.

After painting the wall and using a reinforcing agent, can I still apply tiles again?

It is better not to use the reinforcing agent to stick the tiles, mainly to strengthen the wall. Reinforcing agent is the latest generation of wall curing agent wall sealing curing treatment products, with nano-scale polymer polymer emulsion as the base material and environmental protection additives reaction polymerization polymerization, absolutely free of formaldehyde, benzene and other toxic and harmful substances completely green environmental protection. The unique super physical permeability can penetrate deep into the interior of the wall, and the excellent bonding strength, crack resistance and good alkali, moisture and mildew resistance of the product after curing can make the surface layer of the cement wall or plastering wall and the internal fine loose place completely bonded and compact, thereby improving the overall strength of the wall wall, effectively improving the bonding strength and adhesion of the wall putty batch coating, tile adhesive lead and sticking to the base layer, and is a supporting product for the home improvement wall reinforcement.

After brushing the wall, the brushing needs to be dealt with, because the smooth wall tiles are not very stable and firm, otherwise it will affect the overall aesthetic effect.