What is the reason why the putty cracks shortly after scraping? How to choose putty powder?

It may be that the moisture is not enough, and it was not completely fused when it was scraped, so it will cause cracks in it, and then over time, it will completely crack when it dries a little, and this putty powder should be adjusted very well

What is the reason why the putty cracks shortly after scraping? How to choose putty powder? I think that the putty cracks soon after scraping, so you add less gypsum powder, so it cracks, and when you scrape the putty again, you add a little more plaster, so that he doesn't crack.

After scraping the putty, the wall cracks again, which means that you are a putty powder. If it is too dry, it may also be a problem with the quality of the wall.

Just after the putty, the reasons for the cracks on the wall are: dry shrinkage cracks formed by dry and wet changes, temperature cracks caused by temperature changes and thermal expansion and contraction, and structural cracks caused by static and dynamic loads of wall structural deformation.

You can see if it is the reason for the thickness of the putty layer, and the other is the problem of putty. All of their products have achieved the highest standards of the world's four most stringent environmental certifications.

Putty powder is not easy to scrape too thick, because putty powder has a certain elasticity and crack resistance is not high, so too thick will crack.

The putty cracked shortly after scraping, what is the reason? How to choose putty powder? Putty powder must choose some ingredients in the instructions.

I think it's because when you do this, the moisture may be too dry, so in this case, such a problem will occur, so when we do this, we must pay attention to the harmony of its moisture. to be able to make your level better.

Just scraped the putty, it cracked soon, it may be that the air is too dry, and the wall has no water rhyme, and then the putty is scraped and the window is opened, causing the dryness to dry too quickly, or the putty is too thin.

What is the reason why the putty cracks shortly after scraping? How to choose putty powder?

Decoration design, home design, decoration.

If you just scrape the putty and it cracks soon after, it must be you. There is a reason for the bottom of the wall, or the proportions in your putty are not good.

Before brushing the putty, a mesh cloth should be pasted, and the putty should be scraped a few more.

1. Remove all the original putty, then re-brush the base layer, paint again, and remember that only when the first layer is dry, can the next layer be smeared, effectively prevent cracks in the inner layer, and do not brush the wall too thick, according to the actual situation. 2. If the crack area in the house is relatively large, then it is better to find a professional master directly to come to the door, and the effect will be better.

Reasons for this:

1. It may be because when the putty is scraped, the next layer is applied without waiting for the previous layer to dry thoroughly, resulting in cracking, or due to the change of indoor temperature, resulting in thermal expansion and cold contraction, resulting in temperature cracks.

2. Or it is not done well when making the wall base, or the wall structure is deformed, or it is possible that the quality of the putty purchased is not very good, and the ratio of water and material is not good when batching, maybe the operation is not very good during construction.

3. Maybe it's too thick when scraping putty, or maybe it's not doing a good job of maintenance, such as not cleaning often, not opening windows for ventilation, etc., there are certain factors.

It's possible that the wall is too dry or ventilated too quickly, but there are still many possibilities!

There are many reasons for putty cracking, 1. The previous putty is hung up before it is dry, and the dry and wet changes form cracks, 2. Temperature cracks are caused by temperature changes and thermal expansion and contraction;

3. The base layer is not well treated or the wall structure is deformed and the structural cracks are caused by static and dynamic loads.

4. Poor product quality will cause cracks, mostly due to the wrong material ratio.

5. The putty layer is too thick.

6. Many factors such as asympathy of maintenance methods may cause putty cracking.

First, the putty coating is too thick, and the water absorption rate of the second wall is too high, and many other reasons cause cracking.

There are many reasons for putty cracking, there are external reasons as well as internal causes.

1. Dry and wet changes form dry shrinkage cracks; Temperature cracks caused by temperature changes and thermal expansion and contraction;

2. Structural cracks caused by deformation of wall structure and static load.

3. Use inferior quality, expired greasy, or improper proportioning.

4. The base layer is not clean, the original putty layer is not cleaned up, and the newly bought putty powder has a relatively large grip, which cracks the original putty.

5. The first putty is not dry, and the next batch is scraped.

6. The putty layer is scraped too thickly.

Many factors can cause putty cracking, and it is recommended to find a professional to take a look at the scene.

It is very likely that the bottom treatment of the wall is not done well, and the key to the bottom treatment of the wall is putty.

If you use traditional glue putty, it is easier to crack and fall off the wall, because the traditional glue putty only uses glue to stick the double fly powder on the wall, and the adhesive properties will disappear after the glue volatilizes for a long time, and there will be cracking, falling off and other phenomena. Moreover, the glue contains a large amount of harmful substances such as formaldehyde and benzene.

You can choose putty powder made of gypsum-based raw materials, such as Saint-Gobain aldehyde net series putty powder, the raw materials naturally do not contain harmful substances to the human body, and the bonding properties of the gypsum crystals themselves will not crack and fall off the wall, and the service life is the same as the life of the building.

Hope it helps you solve the problem as soon as possible!

1. When the bottom putty starts to construct the surface layer before it dries, the surface layer is dried first, and the inner layer is still in the process of drying, and the degree of drying and shrinkage between the layers is not the same, and it is easy to crack.

2. The putty is too thick, the internal drying is slow, and the surface drying speed is faster, resulting in cracking. When the base layer is treated, the joints and leveling materials are not completely dried, and the hardness of the interior wall putty is scraped on the top, which is easy to cause cracking.

The thickness of the first putty needs to be determined according to the surface condition of the base layer, and the general thickness is. The first putty allows a slight needle's eye, but no bubbles; The putty should not be too thick at one time, so as to avoid excessive dry shrinkage, which will affect the firm bond between the putty layer and the base layer. When scraping and coating, the force should be balanced, and the surface of the putty layer should be smooth as much as possible, and no obvious rough surface will appear.

When scraping and coating for the second time, it should be high and low, try to make the surface of the putty layer smooth, fill the eye of the needle, and the force should be balanced when scraping and coating, so that the surface of the putty layer is smooth and does not appear obvious rough.

Decorating a house requires putty, which can make the rough and uneven rough wall smooth, so that the wall paint is also smooth and smooth, and the adhesion ability to the wall is also stronger. But sometimes it doesn't take long to scrape the putty, and cracks will appear. At this time, it is generally not necessary to proceed to the next step, but to deal with it as soon as possible.

1. The base layer is constructed before it is completely dried, and the moisture content of the base layer is required to be 10%.

2. The bottom putty is not completely dry, but the surface is dried first, and the inner layer is still in the drying process, resulting in different degrees of shrinkage between the layers and easy cracking.

3. When the base layer is treated, if the repair material is not completely dry, apply hardness of interior wall putty on it, which is easy to cause cracks.

4. The putty construction is too thick, the internal drying is slow, and the surface drying speed is fast, which is easy to cause cracking.

1. If there is a large area of cracks, chisel the wall foundation at the crack into a "U" shape, and the spacing of the "U" grooves is greater than 20cm, chisel the chiseled base, and then hang the wire net.

2. After the wall substrate is cleaned, paste a layer of muslin, kraft paper or newspaper on the wall first, and use the tension of the fiber to ensure the integrity of the latex paint film. This method is relatively simple and easy to implement, but the results are mediocre.

3. Remove the insulation board on the surface of the wall, or remove the cement wall, install a layer of gypsum board or "five-point board" outside the insulation layer, and then apply latex paint on it. This method removes all the irregular cracks. Cracks are usually at the joints between the plates and are easier to deal with.

However, this method is expensive and difficult to build.

4.Use elastic upholstery materials. At present, there is a kind of "elastic putty" that can compensate for wall cracks to a certain extent.

A certain amount of wall paint can also play a role in covering up small cracks in the wall. However, the "elasticity" of these materials themselves is small and will not work on walls with severe cracks.

5. Some consumers simply remove the insulation layer of the wall. Although this method can be done once and for all, it will reduce the thermal insulation performance of the wall, so it is not recommended.

The first step is to choose a qualified putty.

The second step is to understand the ratio of putty to water and stir well.

The third step is to clean the wall and repair the missing corners or cracks with plaster in advance.

The fourth part, the official start of scraping putty. Under normal circumstances, you need to scrape 3 times, but next time you must wait until the last time there is a certain degree of dryness.

The fifth step is the maintenance work of scraping putty. This is mainly needed when the weather is cold.

The sixth step is grinding and polishing.

Home decoration, the wall will be scraped putty, but sometimes, the worker scrapes three times as required, but in the end it takes a long timeThe house is scraped with putty and the walls are crackedOn, why is that?

1.The putty did not dry last time, and it hangs next time. Wet and dry changes can create cracks.

2.Temperature changes and thermal expansion and contraction lead to temperature cracks.

3.Structural cracks caused by poor treatment of the base layer or deformation of the wall structure due to static charge.

4. Poor product quality will causeThe house is scraped with putty and the walls are crackedseams, mainly the material is not in the right proportions.

5. The frankincense layer batch is too thick.

6. Maintenance method is not equal to many factors that may cause putty cracking.

If it is a lightweight partition, nylon mesh or kraft paper is usually used, and the partition itself is prone to small cracks. Therefore, to minimize cracks in home décor, it is better to fill it with glass or bean cloth.

If the bearing wall or solid wall, forThe house is scraped with putty and the walls are crackedThe reason for the opening may be that the putty is too thick or the interval is short during construction, while the putty is not dry. The old house turned into a flat wall.

For old walls, putty and paint must be removed from the original primer. The original room made the original wall decoration used by the Liquid Hui is putty. This putty is easy to spray, peel and peel. The base layer is treated and then painted.

When building the wall,The house is scraped with putty and the walls are crackedPay attention to these issues. The first is the ratio of cement to sand. The optimal ratio is 1 to 3

The conversion of the circuit had to start with the carpentry base, as it would take time to repair it after placing the slot. The drying rate and shrinkage rate of cement mortar is different from that of powder putty.

After the first repair, there will be shrinkage and subsidence. A second fix is also needed to makeThe house is scraped with putty and the walls are crackedand prevent it from cracking.

In the case of cracks in the color of the wall paint, the effect of partial repair is often not very good, because the color of the wall paint will be a significant color difference once it is painted.

If the insulation is broken, cut the crack with a scraper, as deep as possible, fill it with plaster, make sure that the filling, fill evenly, then glue the crack with a bandage fabric, nylon mesh, area, and then place the putty after drying. Or do another process.

The above is a summary of some of the information for youThe house is scraped with putty and the walls are cracked

You can get it for free

How to deal with andJust scraped putty wall cracksCauses.

1. Temperature cracks: This kind of cracks have little impact on the structure of the house. It can be attached in cracked non-woven fabric or mortar cloth crack, and then painted.

2. Crack settlement repair: Cracks must be stabilized after cracks, and the repair can be filled with cement slurry, mortar and polymer gypsum.

1. Look at the walls.

When brushing putty from the surface of the wall, the first thing to check is whether the wall surface is flat. If the wall surface is irregular or has gaps, the wall surface must be repaired.

2. Protect the finished product.

When the walls are painted, some dust or glue from the stove will fall, so it is necessary to do a good job of protecting the finished product inside the house.

3. Preparation.

Before brushing putty, the wall should be cleaned with a steel brush to make the wall dust-free, and then brushed with a uniform layer of concrete interface agent. After drying, you can scrape the putty.

4. Putty. If it is used for a wall with a low degree of flatness, you will need to brush the putty several times to ensure that the wall is flat.

5. Polishing putty.

After a few days of putting the putty on the wall, it will solidify, so after the top wall the next night, start polishing and flatness checking, while crushing.

6. Primer brush.

After smoothing, the primer can be applied and applied evenly.

7. Finish brushing. The top layer should be applied twice, and after a few days of applying the last coat of paint, take care to waterproof, dry and avoid exposure to the sun.

8. Acceptance. Just scraped putty wall cracksFinally, after brushing the putty onto the wall, the wall surface needs to be accepted. After the inspection is completed, it is necessary to verify that the wall surface is flat, there are no joints and that the color is uniform.

1. The first type is to handle the seam filling of the base layer and the filling material without drying. When the inner wall putty is applied to strengthen the hardness, it is easy to make the putty crack. Therefore, we have to wait for the basic drying and then move on to the next step, and the owners sometimes rely on the construction crews for construction, which is the reason.

Just scraped putty wall cracksThe construction requires that the water content of the base layer is less than or equal to 10. Structures that are not drying in the base coat can also cause cracks. It is a matter of proportion, and due to inexperience, substandard buildings will crack.

3. The bottom layer of putty is not dry, the surface layer is dried first, and then the inner layer cannot be dried, which is easy to cause different shrinkage degrees between layers and cracks.

4. The putty brush is too thick, the surface dries faster, and the inside dries slower, which is easy to break.

You can get it for free