How to fix the glass on the wall, how to remove the glass attached to the wall

First. No punch hole installation; The back of the opaque glass "For example, mirror, painted glass" is double-sided tape and glass glue, and it can be cleaned.

Second. Eye-piercing words; First of all, make a hole in the glass, put it in the position to be installed, mark it, punch the hole with a 6mm electric hammer, fix the plastic expansion tube, and fix the mirror nails. If the back is a wooden board or gypsum board, you can just screw it on without drilling holes.

There is also an advertising nail installation method, which is much the same.

Due to the strong viscosity of glass glue, you can carry out low temperature treatment before removing the mirror, and the temperature price can reduce the viscosity of glass glue, at this time, you can use a utility knife to stick it flat on the wall, cut it little by little, or you can use a saw blade, stick to the wall and slowly cut it, for a large area of mirrors, you can use white construction line, nylon line, the friction of the line is very large, from the corner of the mirror with a sawing action, pull back and forth to remove the mirror. Try to stick transparent glue on the mirror surface to avoid breaking the mirror with too much force or pricking your own hands.

1. If the mirror on the wall is glued, such as double-sided tape, the stickiness is relatively sufficientIn this case, we can first adjust the hot air to the gear of the hot air with a hair dryer and blow it against the glue in the back. Because under high temperature, the glue will melt, and when it softens, the mirror can be removed, and the mirror needs to be held so that it does not fall on the ground and break.

2. In addition, low temperature treatment can also be adoptedPrepare a few ice cubes and cool them in front of the mirror, so that it will not hurt the mirror and the wall. After a little waiting, it will be able to dissolve, and it will be very easy to take it again.

3. If it is fixed with advertising nailsYou need to remove the cap first, and then prepare a screwdriver to loosen the screws, and then you can remove the mirror directly.

4. If it is some mirrors with a relatively small sizeYou can use a wallpaper knife to slide down against the back of the mirror, so that it is tightly attached, but you must also be careful not to hurt the wall.

5. Use alcohol to dissolve the glueSpray the alcohol between the mirror and the wall, so it will also be easier to take it off.

You want to stick a mirror to the wall, especially in the bathroom. If you choose to use glue, you can use glass glue, and it is best to choose neutral. Don't choose acidic ones, or they will most likely corrode the back of the mirror.

This is a commonly used adhesive with very strong viscosity and is more suitable for the connection between glass and wall. First of all, you need to wipe the mirror and the wall clean, and then squeeze the glass glue evenly on the back of the mirror and the corresponding wall, and then press it hard. Maintain a certain pressure, about 4 or 5 minutes, and then loosen it, it can have the effect of bonding, and finally open the window to ventilate, so that the drying speed is faster.

1. Prepare a 22 or 18 iron wire (for the ceiling, for tying steel bars) that is one meter to two meters longer than the width of this glass on both sides (depending on the operating environment).

Second, one person on both sides of the glass, clamp the wire with iron pliers, put it on the top of the glass, close to the wall, the two find the best angle, and pull back and forth (the two work hard to cooperate well, and proceed steadily at once (like pulling a big ju), note: When it is about to be pulled to the end, two more people (those with strong hands and experience in moving glass) can catch it.

How to remove the glass attached to the wall: 1. Prepare a 22 or 18 iron wire (for the ceiling, for tying steel bars) that grows one meter to two meters on both sides of the width of the glass (depending on the operating environment). Second, a person on both sides of the glass, clamp the wire with iron pliers, put it on the top of the glass, close to the wall, the two find the best angle, and pull back and forth (the two work hard to cooperate, and proceed steadily (like pulling a big ju), note:

When you are about to pull to the end, two more people (those with strong hands, those who have experience in moving glass) can catch them.

Glass can be fixed to the wall by nailing, pasting, embedding and other methods, and different glass has different ways to fix.

1. Nailing method: fix the glass on the base layer of the wall with screws, and then wrap it around it, so that it is not easy to hurt people, and it is very firm It is suitable for most glass installations, but for oversized glass, the number of screws, the safety distance quotient, and the thickness of the mirror should be considered.

2. Paste method: use adhesive with relatively high paste strength to paste the glass directly on the base layer of the wall, this method is suitable for the installation of the wall environment within 1 square meter, and it is best to use the method of combining paste and nailing to ensure that when the mirror is damaged, it will not fall and hurt people.

3. Embedded method: stainless steel, aluminum alloy or wood line is used to make the frame of the glass mirror, and the frame is fixed with the wall base layer by nailing method, and then the glass is inlaid in the frame, which is suitable for the installation and fixation of large-area glass.

Use glass glue to install and fix the glass, usually to combine hard decoration to construct, in the early stage of construction to leave the groove of the inlaid glass, the glass is placed on and then fixed with glass glue.

If the glass is tempered, then there are generally requirements for installation, such as leveling the wall, nailing the aluminum alloy or stainless steel groove and installing the tempered glass into the groove, and playing glass glue or structural adhesive. If it is the curtain wall glass of the exterior wall, there are extremely professional installation specifications, and it is recommended that users inquire.

Users can also use alloy or stainless steel edging: this method is a relatively common practice in ordinary home decoration, with an alloy or stainless steel frame to wrap the glass and fix the frame to the wall.

The methods of fixing the glass on the cement wall are: using high-strength glass glue or corner drilling, self-tapping nails, decorative buckles, etc. It can also be pasted on both sides, and the surrounding area is made of glass glue. It is recommended to do glass frame inlay or glass corner drill holes with anchor bolts.

Here's how:

1. Nailing method: This method is to fix the decorative glass mirror on the base layer of the wall (or cylinder surface and top surface) with screws.

2. Paste method: use adhesive with high bonding strength to paste the glass mirror directly on the base layer of the wall. This method is suitable for the installation of wall surfaces up to 1 square meter.

If the size of the mirror is large, or it is a ceiling-mounted mirror, it is best to use a combination of pasting and nailing to ensure that the mirror will not fall and hurt people when it is damaged.

。。。If it's plexiglass, I've done it, and I've put it on the screw (with an electric drill.) ）。

I haven't tried inorganic glass...

Please ignore me in the case of inorganic glass =-= )

How to remove the glass attached to the wall: due to the strong viscosity of the glass glue, you can first carry out low temperature treatment before removing the glass, and the viscosity of the glass glue can be reduced when the temperature price is low. Try to stick transparent glue on the glass to avoid breaking the mirror or pricking your own hands with too much force.

The glass can be fixed on the wall by nailing, pasting, embedding and other methods, and different glass has different ways to fix.

1. Nailing method: fix the glass on the base layer of the wall with screws, and then wrap it around it, so that it is not easy to hurt people, and it is very firm It is suitable for most glass installations, but for oversized glass, the number of screws, the safety distance quotient, and the thickness of the mirror should be considered.

2. Paste method: use adhesive with relatively high paste strength to paste the glass directly on the base layer of the wall, this method is suitable for the installation of the wall environment within 1 square meter, and it is best to use the method of combining paste and liquid nailing to ensure that when the mirror is damaged, it will not fall and hurt people.

3. Embedding method: use stainless steel, aluminum alloy or wood lines to make the frame of the glass mirror, use the nailing method to fix the frame and the wall base layer to talk about infiltration, and then inlay the glass in the frame, this method is suitable for the installation and fixation of large-area glass.