Who s to blame for scraping the white wall and falling off the wall

Updated on home 2024-07-13
6 answers
  1. Anonymous users2024-02-12

    In view of the problem you mentioned, I think there are four. The first is that when your house is built, the ratio of cement to sand and ash is too small. The solution is to brush 108 glue (that is, polyvinyl alcohol glue) on the top when there is no white shaving.

    Second, the paint on the bottom of your wall is not cleaned, and you are scraping it white. Solve the bottom of the wall and clean it, and then scrape it white, or brush 108 glue (that is, polyvinyl alcohol glue) again. It's better that way.

    Third, the bottom of the wall cement is not dry and alkali caused by peeling. Solve the problem of waiting for the bottom of the wall to dry and then scrape the white, or scrape and polish the alkali resistant primer again, and then paint it. The fourth is that the big white putty you use is not good, just solve the good putty.

  2. Anonymous users2024-02-11

    When renovating an old house, you should first check whether the plastering base can be used, if not, you need to remove the original plastering layer and re-plaster it before you can paint it.

  3. Anonymous users2024-02-10

    The cement of the old wall is weathered, and the putty should be scraped before scraping the putty, and then the putty should be scraped again with a 108 glue brush.

  4. Anonymous users2024-02-09

    Clause. 1. When the house is under construction, it is caused by the ratio of cement and sand and ash is too small.

    The solution is to brush 108 glue (that is, polyvinyl alcohol glue) on the top when there is no white shaving.

    Clause. Second, the paint on the bottom of the wall is not cleaned, and it is scraped on the top.

    Solve the bottom of the wall and clean it, and then scrape it white, or brush 108 glue (that is, polyvinyl alcohol glue) again. It's better that way.

    Clause. Third, the bottom of the wall cement is not dry and alkali caused by peeling.

    Solve the problem of waiting for the bottom of the wall to dry and then scrape the white, or scrape and polish the alkali resistant primer again, and then paint it.

    Clause. Fourth, the big white putty used is not good, solve: the putty is good to replace.

  5. Anonymous users2024-02-08

    The main problem is that the decoration team did not explain it clearly to you, and the decoration team knew about this later situation, but did not know how your contract was made at that time.

  6. Anonymous users2024-02-07

    What to do if the white wall is peeled: 1. If the first area of the small base dust is removed, it can be smoothed with sandpaper next to a small part of the area, the skin can be cleaned up, removed, and then sanded with sandpaper, and then scraped putty and painted.

    2. If the wall is completely eradicated in a large area and reconstructed, the wall should be completely removed, leaving only the base layer, and the construction of the paint should be re-carried out. However, if it is only a skin problem, the top layer can be removed and sanded, and the topcoat can be re-applied.

    3. If only a little skin is directly treated, if the wall is only a little peeled, the surface layer can be directly cleaned, and then the topcoat is painted, which is usually completed by roller coating.

    This answer applies to most wall peeling cases.

Related questions
9 answers2024-07-13

First, the putty scraping technique is fast and flat.

First, put an appropriate amount of water into the bucket, generally no more than one-third of the volume of the bucket, then pour in an appropriate amount of putty powder, install the electric drill on the mixing head, turn on the electricity to stir, and stir until it is sauce-like. >>>More

5 answers2024-07-13

1. Use paint.

If the balcony is only painted, it will not be long before the walls will become moldy or even peel off due to moisture. Choose to paint the balcony wall with exterior wall paint, which has the function of sun protection. Special special, professional exterior wall paint for balcony walls, one of its important indicators is anti-ultraviolet radiation, even if it is irradiated for a long time, it will not change color. >>>More

10 answers2024-07-13

The main causes of peeling are:

1. The stucco layer is hollow; >>>More

20 answers2024-07-13

The interior walls of the new office are only scraped putty, which is scraped by their own people, and in this case, the environment will also contain formaldehyde. As an adult, you should know that when you renovate the office, you should try to wait for the office to be placed for a week, and all the putty in the room has dried before you can use it for office use. At the same time, before use, you should also test how high the formaldehyde content is, and only when the formaldehyde content in the house is judged to be relatively low, employees can work in the office. >>>More

2 answers2024-07-13

A few days ago, a few tiles suddenly fell from the house, but fortunately they didn't hit anyone, which scared me to death! There is no problem with looking very stable during acceptance, but when the wall tiles are removed, it is simply caused by not shoveling the wall skin. I can't find the person in charge of the renovation, where can I reason? >>>More