-
First of all, don't worry, it's a very patient problem to open under the zipper, first of all, calm down, take a drink, untie your clothes, cool and cool.
You won't be able to pull it hard, so you'll need to pinch the head of the zipper and try to pull one side with the other hand. Isn't the zipper on the left and right, you pull one side, there must be one side on both sides that can be pulled, but ah, you can only pull one square, you hear a "cluck" sound, this is a play, and then, you pull the other side. Cycle through to the bottom.
If the above method does not work, try dripping some oil or laundry detergent. Then do it according to the above method, and pull it apart.
There is also a situation where the fabric of the garment jams the zipper. Remember, don't pull down, it's the same reason, the zipper can't be pulled back if it's stuck, and it can't be pulled back if you card more cloth, so be sure to pull it up, so that the fabric has a high probability of being pulled out. After the fabric is pulled out, do what I wrote above.
I hope it helps.
-
Pull the zipper puller to the top, pull the corner of the zipper puller along the card slot in an oblique direction, and pass the new zipper puller diagonally from the card slot according to the method just now, and pull it to the bottom.
-
Now there are some small alleys where there are zippers that you can go to and fix your zippers, usually no more than five dollars.
-
Tools required: taper pliers, scissors, needle, thread.
Steps: 1. We pull the zipper to the very bottom, make a comparison with the side of the zipper, and find the chain teeth parallel to the zipper head.
2. We use scissors to cut off this chain tooth.
3. Next, there is a gap after cutting.
4. We put the zipper through this notch.
5. Pull it up and get it back on track.
6. Sew the mouth of the chain teeth cut with a needle and thread, and sew it a few more times to make it firmer, so that when you pull the zipper down again, you don't have to worry about the zipper head running out.
7. After the repair is completed, use pliers to clamp the two ends of the zipper slightly.
8. The repair is complete.
-
Prepare materials: awl, pliers.
6. Done.
-
The zipper puller has fallen off, how can I easily put it back in? It's actually very simple, and you can learn it at a glance.
-
Hello dear! How to install the chain head off: First prepare a lighter, use the lighter to burn the cloth surface of the fallen off end to prevent it from falling off, and place the zipper on the table with the level facing up.
Pull the zipper head into the teeth with the teeth facing up, and pull both ends of the cloth belt together and pull it outward.
The zipper head will go down the tension of the cloth belt to the outside into the teeth, and the slider will be installed after the cloth belt is pulled out, pull out the excess teeth with oblique nose pliers, do not use too much force, so as not to break the cloth strip, install the lower teeth to prevent the zipper from sliding out.
When using it at ordinary times, if the zipper is loose and the teeth are missing, you can use a small hammer to gently knock a few times on the zipper head to make the upper and lower chain teeth bite tighter, and the teeth will not be removed again.
-
1. The lighter burns the edge of the cut cloth tape to prevent it from falling off. 2. In the upward direction between the teeth, pull the zipper head into the teeth, pinch both ends of the cloth belt with both hands, and pull it outward together, and the zipper head will enter the teeth along the outward tension of the cloth belt. 3. After the cloth belt is pulled out, the zipper puller is installed.
4. Pull out the excess teeth with oblique nose pliers. 5. Install "up and down". <
1. The lighter burns the edge of the cut cloth tape to prevent it from falling off.
2. In the upward direction between the teeth, pull the zipper head into the teeth, pinch both ends of the cloth belt with both hands, and pull it outward together, and the zipper head will enter the teeth along the outward tension of the cloth belt.
3. After the cloth belt is pulled out, the zipper puller is installed.
4. Pull out the excess teeth with oblique nose pliers.
5. Install "up and down".
-
The steps are as follows: 1. After cutting, the lighter burns off the edge to prevent it from falling off.
2. Pull the zipper head into the teeth along the upward direction of the teeth, pull the two ends of the tape (arrow position) together and pull outward (as shown in the figure). The zipper will follow the tension of the tape into the teeth.
3. After pulling out the cloth, the slider has been loaded.
4. Extract the extra teeth with diagonal nose forceps.
5. Install up and down.
If you want to keep it, apply a film to the back of the glass. Plays a protective role. It won't hurt people with glass.
Click and key on "My Computer", select "Manage", open the window of plan management, select the "Disk Management" item on the left, then select "G" in "Disk 0" on the right, right-click on "G", select "Delete Logical Disk", now the G drive has been deleted, and then use the remaining space to create a new G disk. >>>More
Pregnancy symptoms, women's infection treatment of anti-women's head headache and pregnancy, is or head and face women's pressure labor will be treated, pain and more common. The water family to the state has, the pain He Zhuan is like the first cause in the Shao woman period should be palpitations of the original head swollen and faint of the pregnant high and thin heart and ear. Accompanied, pregnant eyes, and now blood pregnancy >>>More
Hello, friend.
Personally, I think that if you have itchy head during confinement, you can wash your hair with hot water, which can relieve the symptoms of itching. >>>More
Hurt? Then bear the blow, reflect on what you did wrong, and let a girl who has been with you for 4 years leave you like this, then maybe you can still be saved. >>>More