What should I do if the joints of the wooden floor bulge after being blistered?

The position of the sand hole of ordinary wood flooring is on the edge and the surface of the board, and the edge of the sand hole refers to the bulge that occurs on the edge of the board, which is individual or can be sometimes, and there is no regularity. Blistering is also well understood, and the floor bulges that appear on the board surface, which are common for ovals. To solve this problem, we must first find the cause and analyze whether there is a problem.

After the floor is installed, it is always inevitable to be stepped on, and in this process, the balance layer of the moisture-proof film and the reverse side of the floor are destroyed, and moisture will enter, resulting in a bulge on the floor. Moisture-proof and waterproof works that are not done during installation will also blister the wooden floor, because the floor is in a humid environment for a long time, and moisture can easily enter the floor.

<> according to the situation, the severity of the bubble must be changed, the light is wait-and-see, the heavy can not be recovered, but also depends on what quality of the floor in your home is reinforced and composite, *** can, if it is poor, you don't have to make a small bench now, I heard about this method. If it is a small area of the floor joint will become warped, you can use a heavy object to press on it, after a period of time can be restored, the floor at this moment may not be as good as before, you can try to wax the floor, in serious cases, you can only change the floor locally. If it is a large area of blistering, we can also go directly to the after-sales repair.

In our usual decoration, as long as we pay a little attention to maintenance, we can extend the service life of the wooden floor and avoid the above problems well. When the floor is just laid, pay attention to ventilation and do not trample vigorously;When moving things at home, avoid pushing and dragging to avoid scratching the surface of the grinding layer;If there are water stains on the floor, clean them up in time and use a dry mop as much as possible.

Do a detailed interpretation of the problem, I hope it will help you, if you have any questions, you can leave me a message in the comment area, you can comment with me more, if there is something wrong, you can also interact with me more, if you like the author, you can also follow me, your like is the biggest help to me, thank you.

At this time, you can apply some beauty cream around the area, or you can choose to remove the stitches of the wooden floor, and then re-lay the floor, you can apply some quicklime around.

You can choose to change the floor, or you can choose to replace the soaked area, and you must pay attention to it at ordinary times and try not to let the floor touch the water.

You can clean the cracks in the floor first, and then remove all the stains inside, and then replace the floor, so that it can be treated.

The solution to the gap in the wooden floor after being blistered:

1. If the gap of the wooden floor is not very large, then you can use white glue to stir the sawdust, and then fill in the gap of the floor, and after drying, polish it with fine sandpaper. If the gap of the wooden floor is too large and loose, it will affect the appearance and normal use. Then you can disassemble the wooden floor, clean it, apply glue, re-lay it and press it, and the glue can be dried after it is dry.

If the area of the wooden floor with large gaps is large, it is necessary to resurface the wooden floor completely.

2. The most effective way to solve the problem of the gap between the wooden floor is to add a humidifier in the house to keep the humidity in the house stable. When the humidity is right and stable, the large gaps between the wooden floors will naturally and gradually become smaller and return to their original shape.

This should be handled by a professional installer.

Is it a partial or large area of water?

Wooden flooring is the most afraid of water during use, even if you are more careful during use, it is inevitable that some accidents will occur, if the wooden floor at home is blistered in an unexpected situation, what to do? First, blot the water on the floor. At the same time, you can use a water absorber to absorb water vapor in the splicing gap of the soaked floor, or use a hair dryer to dry it with cold air.

Secondly, if the seam is only a small area of warping, you can use a weight to press on it.

Paving method.

1. Pavement from left to right or from right to left in turn, groove to the wall, put a wooden wedge between the floor and the wall, leave enough expansion joints, dry areas, the floor is wet, and the expansion joints should be small; In humid areas, the floor is dry, and the expansion joints should be left large. Check the straightness of the floor with the pull line, check with the shop during installation, observe the height difference and gap of the board surface during the trial paving, adjust it at any time, and only after passing the inspection can the sizing installation. Generally, spread on the side 2-3 rows, apply a small amount of D4 or waterless environmental protection glue to fix.

The rest of the middle part is completely meshed by the tenon groove, and there is no need to apply glue.

2. The last row of floors should be cut and glued by measuring its width, and there is a hook or screw top to make it tight.

3. In some particularly humid areas such as East China, South China and Central South China, when installing the floor, the floor is generally not too tight between the floors (usually the thickness of a business card can be stored between the floors). In the Northeast, Northwest and North China, it is generally better to lay the floors tightly.

4. Closing bridge installation.

At the interface connection between the room, hall and hall, the floor must be cut off, and the expansion joints must be left full, and the door and the ground should be connected with a sufficient distance of 3-5mm so that the door can be opened and closed freely.

5. Skirting board installation.

The thickness of the optional baseboard should be greater than 15mm, and the gap between the expansion joints of the floor should be within 5-12mm during installation, and the polystyrene board or elastomer should be filled to prevent the floor from loosening. If the wall or foundation is uneven, the appearance of gaps is expected, you can ask a decorative wall worker to repair the joints.

1. On-site inspection.

Sports wood floor maintenance staff, or stadium staff, when they find that the sports wood floor is soaked in water after work, don't panic first, be calm. Conduct an inspection of the soaking site at the first time to eliminate potential safety hazards.

For example, there are no wires, electrical appliances, flammable and explosive materials on the soaked floor.

Wait. Then according to the degree of water immersion of the sports wood floor, a solution is formulated.

2. Soak in water lightly.

If the sports wood floor is lightly soaked, the lightly soaked and damp floor can be wiped dry and ventilated. If necessary, disassemble the sports wood floor to observe whether there is water on the ground and observe whether the floor is obviously deformed. If so, it needs to be removed and dried, and reinstalled.

3. Heavy soaking.

Sports wood flooring that is seriously damp or soaked in water for 30 minutes will be deformed, expanded, and lost its luster. Such sports wood flooring is basically scrapped and should be replaced, and attention should be paid to removing the moisture under the floor and drying it.

4. Precautions.

After soaking the sports wooden floor in water, you must pay attention to whether it is not a hair dryer.

Blowing, sun exposure, and drying will accelerate the serious deformation and damage to the surface of the sports wood floor of the basketball hall.

If it is a solid wood floor, there is a keel underneath, so it must be removed, let the keel dry, the floor is dried upright in the indoor ventilation, do not be exposed to the sun, or roasted by fire, and it can be reinstalled without deformation after drying.

If it is a composite floor, you also have to take the floor down to dry first (provided that your floor is glue-free paving, and the glue will be scrapped), look at the specific warping situation, if it is not very serious, it can still be used, if it is more serious, it can only be replaced.

No matter what the floor is blistered, it is difficult to restore the original state, generally it is to warp, but the degree is different, *** will be better, like you said this situation, it should be difficult to recover, even so, you must be mentally prepared, the soaked floor may bulge or appear expansion joint deformation in the summer or winter of the next year.

The wooden floor is not particularly soaked in water, just need to basically clean the water on the surface of the floor, and you can use a vacuum cleaner to blot the water and blow it with a hair dryer. If the local floor is blistered and bulging, you can first clean the water on the surface of the ground, and then remove the baseboard and the door pressure strip, open the window to ventilate and dissipate the moisture on the surface of the floor. If it is a large-scale soaking situation, the floor will generally be scrapped, no matter what a good floor wrench or a bad floor, whether it is a solid wood floor or a laminate floor, a large area of water soaking, especially for a long time soaking, even if you absorb the water or the surface of the floor looks like there is no water, but after a period of time the floor will be deformed, so there is no good way to do this, you can only replace the floor.

There is no way!

I have to replace the floor!

The project is relatively large.

This is difficult to recover, if it is a solid wood floor, it can be flattened with a heavy object on the surface, and it will recover on its own after a few months, if it is a composite floor, it is basically impossible to recover because the internal material is damp and expanded.

What should I do if my wooden floor is blistered? The gap was bulging.

The treatment method of large gaps in the wooden floor after soaking in water is as follows: 1Patch with patching wax:

If the seam is within the scope of repair, it can be repaired with repair wax. Specifically, the repair wax is adjusted to a similar color to the wooden floor (you can ask for the help of after-sales professionals) and then poured into the crevices. 2.

After the furniture wood floor is blistered by small water, you will find that the furniture wood floor interface is protruding, if this problem occurs, what to do? This is a way to solve the protrusion of the furniture wood floor, and there is also a way to prevent the protrusion of the furniture wood floor, and I hope to give you some assistance.

1. Disassemble for natural ventilation and drying. Removing the arching block and the nearby wooden floor to allow it to be naturally ventilated and plugged can alleviate the arching problem; Large-scale prie up the wooden floor at the arch, wait for the sky and the dragon to be restless, and then pave the ground home; Pay attention to the normal contact between the wood floor and the outside to balance it with the humidity of the air environment; If the arch is more serious, you can think about replacing it. In order to prevent the arching of the wooden floor, the experienced pavement master will vacate a certain small gap in advance when laying the wooden floor, leaving the indoor space of "hot expansion and cold contraction" for the wooden floor.

2.Gap garbage disposal can not be ignored, when laying the floor, there will be gaps between the floors, this is to facilitate the space provided by thermal expansion and contraction, but after a long time, there will be garbage in the cracks, if it is filled with garbage, it will cause the floor to bulge, and it is necessary to clean it in time.

3.If the floor has been flooded, first treat the floor water quickly, and then remove the kicking line against the wall, so that the floor has a retractable space, and the water inside can be better volatilized, so that after 1-2 weeks, it can be.

4. Replace the wooden floor of the furniture

Replace the new wooden floor, when repairing, remove the deformed floor block, level the air with concrete, and replace the new wooden floor, so that the wooden floor will be leveled as first seen (during the warranty period, the customer can immediately contact the ** merchant to terminate the replacement).

How to prevent bulging furniture wooden floors.

1. Ensure that the pavement material is boring

When paving wooden floors, ensure that concrete or thermal insulation and sound insulation materials are boring and boring, if not boring, it is essential to be boring before paving wooden floors.

2. Moisture content of wooden floors

Manipulating the moisture content of the wooden floor, its moisture content does not exceed 12%. If you encounter a humid environment, remember to ventilate the room to avoid the wood floor bulging due to the humidity in the air.

3. Embedded deformation joints

When the wooden floor is paved, it is necessary to leave a gap of 2 cm as a deformation joint when it is paved to the wall. A gap of 1omm should be left between the overall surface layer of the woodworking board and the wall, and it should be sealed with a foot guard or baseboard.

First, use a vacuum cleaner to suck the water on the floor to let the gaps in the floor be dry, and then pry the soaked floor open in a cool place, let it dry slowly and then lay the floor back on.

Remove the baseboard of the floor and expose the expansion joints to disperse the moisture, or you can use a hair dryer to dry it, or use a vacuum cleaner to suck up the moisture, or you can repaint and wax the floor.

The water on the floor should be cleaned up, and then the blistered floor should be remedied by taking care of it, and the later maintenance should be done.