What to do if there are gaps in the wooden floor after being blistered

1. On-site inspection.

Sports wood floor maintenance staff, or stadium staff, when they find that the sports wood floor is soaked in water after work, don't panic first, be calm. Conduct an inspection of the soaking site at the first time to eliminate potential safety hazards.

For example, there are no wires, electrical appliances, flammable and explosive materials on the soaked floor.

Wait. Then according to the degree of water immersion of the sports wood floor, a solution is formulated.

2. Soak in water lightly.

If the sports wood floor is lightly soaked, the lightly soaked and damp floor can be wiped dry and ventilated. If necessary, disassemble the sports wood floor to observe whether there is water on the ground and observe whether the floor is obviously deformed. If so, it needs to be removed and dried, and reinstalled.

3. Heavy soaking.

Sports wood flooring that is seriously damp or soaked in water for 30 minutes will be deformed, expanded, and lost its luster. Such sports wood flooring is basically scrapped and should be replaced, and attention should be paid to removing the moisture under the floor and drying it.

4. Precautions.

After soaking the sports wooden floor in water, you must pay attention to whether it is not a hair dryer.

Blowing, sun exposure, and drying will accelerate the serious deformation and damage to the surface of the sports wood floor of the basketball hall.

If it is a solid wood floor, there is a keel underneath, so it must be removed, let the keel dry, the floor is dried upright in the indoor ventilation, do not be exposed to the sun, or roasted by fire, and it can be reinstalled without deformation after drying.

If it is a composite floor, you also have to take the floor down to dry first (provided that your floor is glue-free paving, and the glue will be scrapped), look at the specific warping situation, if it is not very serious, it can still be used, if it is more serious, it can only be replaced.

No matter what the floor is blistered, it is difficult to restore the original state, generally it is to warp, but the degree is different, *** will be better, like you said this situation, it should be difficult to recover, even so, you must be mentally prepared, the soaked floor may bulge or appear expansion joint deformation in the summer or winter of the next year.

The solution to the gap in the wooden floor after being blistered:

1. If the gap of the wooden floor is not very large, then you can use white glue to stir the sawdust, and then fill in the gap of the floor, and after drying, polish it with fine sandpaper. If the gap of the wooden floor is too large and loose, it will affect the appearance and normal use. Then you can disassemble the wooden floor, clean it, apply glue, re-lay it and press it, and the glue can be dried after it is dry.

If the area of the wooden floor with large gaps is large, it is necessary to resurface the wooden floor completely.

2. The most effective way to solve the problem of the gap between the wooden floor is to add a humidifier in the house to keep the humidity in the house stable. When the humidity is right and stable, the large gaps between the wooden floors will naturally and gradually become smaller and return to their original shape. Wish.

This should be handled by a professional installer.

Is it a partial or large area of water?

Wooden flooring is the most afraid of water during use, even if you are more careful during use, it is inevitable that some accidents will occur, if the wooden floor at home is blistered in an unexpected situation, what to do? First, blot the water on the floor. At the same time, you can use a water absorber to absorb water vapor in the splicing gap of the soaked floor, or use a hair dryer to dry it with cold air.

Secondly, if the seam is only a small area of warping, you can use a weight to press on it.

Paving method.

1. Pavement from left to right or from right to left in turn, groove to the wall, put a wooden wedge between the floor and the wall, leave enough expansion joints, dry areas, the floor is wet, and the expansion joints should be small; In humid areas, the floor is dry, and the expansion joints should be left large. Check the straightness of the floor with the pull line, check with the shop during installation, observe the height difference and gap of the board surface during the trial paving, adjust it at any time, and only after passing the inspection can the sizing installation. Generally, spread on the side 2-3 rows, apply a small amount of D4 or waterless environmental protection glue to fix.

The rest of the middle part is completely meshed by the tenon groove, and there is no need to apply glue.

2. The last row of floors should be cut and glued by measuring its width, and there is a hook or screw top to make it tight.

3. In some particularly humid areas such as East China, South China and Central South China, when installing the floor, the floor is generally not too tight between the floors (usually the thickness of a business card can be stored between the floors). In the Northeast, Northwest and North China, it is generally better to lay the floors tightly.

4. Closing bridge installation.

At the interface connection between the room, hall and hall, the floor must be cut off, and the expansion joints must be left full, and the door and the ground should be connected with a sufficient distance of 3-5mm so that the door can be opened and closed freely.

5. Skirting board installation.

The thickness of the optional baseboard should be greater than 15mm, and the gap between the expansion joints of the floor should be within 5-12mm during installation, and the polystyrene board or elastomer should be filled to prevent the floor from loosening. If the wall or foundation is uneven, the appearance of gaps is expected, you can ask a decorative wall worker to repair the joints.

The wooden floor was blistered and bulged, how to deal with it:

1. Ventilation treatment.

First of all, let the floor dry as soon as possible, let the water play out as soon as possible, so that the bulging floor will recover naturally. Therefore, the doors and windows should be opened as soon as possible when the floor is flooded, so as to speed up the air convection and allow the moisture to play quickly.

2. Slit garbage disposal.

When laying the floor, there will be gaps between the floors, which is to facilitate the space provided by thermal expansion and contraction, but after a long time, there will be garbage in the cracks, and if it is filled with garbage, it will cause the floor to bulge, so we also need to clean up the garbage in the fine joints of the tiles, so that the floor will not bulge when the thermal expansion and cold contraction.

3. Demolition angle line treatment.

If the floor has been flooded, first treat the floor water quickly, and then remove the kicking line against the wall, so that the floor has a space to expand and contract, and the water inside can be better volatilized, so that after 1-2 weeks, it will be OK.

4. Hair dryer treatment.

If there is not a lot of water on the floor, you can first use a dry rag to absorb the water, use an electric hair dryer with cold air, blow it on the gap in the floor, blow the water dry, and then press the heavy object on the floor area with water ingress, and it will recover after a while.

In life, some people's homes are equipped with wooden flooring, laminate flooring, etc., which bring many benefits to people's lives, but they may also encounter troubles. For example, if the floor is soaked in water due to the bursting water pipe at home, the floor will also be soaked in water, and then it will be properly bulging, which is much worse than the smooth and flat effect of the normal floor. After the floor is soaked in water, many owners are also worried, afraid that their houses will be destroyed.

So, what to do if the floor is soaked and bulging?

What to do if the floor is soaked in water and bulges

a.Remove the baseboard.

Let's look at how the floor baseboard is installed, now the floor baseboard is generally installed by snap-on, and the corner line is carefully removed from the floor baseboard installed by snap-on. If the floor baseboard is installed with nails or glue, it can only be pried open with a tool.

b.Remove the floor.

The process of removing laminate flooring is relatively simple, using a flat-top screwdriver to pry the baseboard open, and then pry the corner floor along the edge of the baseboard and remove it. When removing the solid wood floor, remove the baseboard first, and then start from the corner of the wall, and use a nail hammer to pry the wooden floor up and pull it out.

c.Floors are placed back to back (please clean the floor surface carefully) and are pressed on top of each other. Place it in a ventilated and dry place to dry naturally, and you can use a fan to blow it, but do not bake or expose it to direct sunlight.

d.After the floor is dry (about 7 to 15 days, depending on the local humidity and the degree of recovery of the floor), measure the thickness of the floor and check its deformation (such as distortion of solid wood, tile change, etc.).

e.Floors that have been largely restored can be resurfaced, and floors that are slightly deformed can be resawed or laid under furniture or in areas that do not affect the overall aesthetics.

f.When dismantling and resurfacing floors, there is bound to be some wear and tear. The owner needs to supplement some flooring appropriately according to the wear and tear of the floor.

How to avoid soaking the floor with water

1.After the floor is paved, some owners will choose to ask a cleaning company to clean it, but some unprofessional cleaning companies use the cleaning method of washing the floor (or using an unwrung out mop), resulting in the floor being damp and deformed.

2.The negligence of the owner in the process of use, the local water immersion in home life will also cause the floor to be damp and deformed, such as water pipe leakage, hidden pipeline water seepage, heating pipe leakage, water dispenser leakage, bathtub leakage, etc. The owner forgot to close the windows when he went out, and the rainstorm caused the rainwater to seep into the ground from all directions such as exterior walls, balconies, toilets, ceilings, etc., causing the floor to be damp and deformed.

3.The deep ground is not dry, due to the rush of the construction period, forced paving, especially when the interior decoration and cement place, although the surface is dry, but in fact the deep ground is still very wet, please pay special attention to this.

What to do if the floor is soaked in water and bulgesThe floor soaking should be able to be repaired in time, even if there is no difference on its surface, it is necessary to disassemble the floor to see the inside, there must be moisture, if the water is not removed, the floor will corrode from the inside to the outside, causing great trouble. If you live on a low floor and may get water during the rainy season, it is recommended that you do not install flooring and use ordinary tiles to have a good waterproof effect.

What should I do if my wooden floor is blistered? The gap was bulging.

The treatment method of large gaps in the wooden floor after soaking in water is as follows: 1Patch with patching wax:

If the seam is within the scope of repair, it can be repaired with repair wax. Specifically, the repair wax is adjusted to a similar color to the wooden floor (you can ask for the help of after-sales professionals) and then poured into the crevices. 2.

Nowadays, people are more and more pursuing texture in home decoration, among which wooden floors are favored by the public for their comfortable foot feel. However, special attention should be paid to the maintenance of wooden flooring during use. But sometimes you forget to turn off the faucet or forget to close the window, which can cause the wooden floor to be blistered.

How can this be remedied? Different floors, remedies are also different, let's learn the relevant knowledge immediately.

1. The wooden floor is soaked in water in a large area.

1. Laminate flooring and solid wood flooring are soaked in water in a large area.

Laminate flooring and solid wood flooring are more afraid of water, and if such flooring is soaked, it is likely to be bent and deformed. In this case, it is difficult to solve by removing surface moisture. The best solution is to lift this part of the soaked floor and wipe off the moisture on the surface of the floor; The floors are then stacked on top of each other in a "well" shape with the reverse side up to prevent them from deforming and waiting for them to dry before putting them back on.

If there is still no way to solve it, you should quickly contact the flooring supplier and let the manufacturer solve it for you.

2. Laminate flooring is soaked in water in a large area.

Laminate flooring has good water resistance, if this material floor is soaked in water in a large area, as for the soaking time is not more than 12 hours, it is still easier to deal with. Wipe the water stains on the surface of the floor first, remove the baseboard and rely on the expansion joints to drain the water vapor, and it can be restored to normal use after 7-15 days. If the floor does not return to normal performance after 15 days, it can only be replaced.

2. The floor is partially soaked in water.

1. Treatment of local soaking of solid wood floor laid by keel.

Wipe the surface moisture clean first, then pry up the soaked floor and leave it in a ventilated place to dry. To make the moisture dry faster and more thoroughly, it is best to pry up the opposite floor along the direction of the keel laying to achieve air circulation under the floor, so as to carry away the moisture.

2. The vacuum cleaner sucks away the water vapor method.

Wipe the water on the surface of the wooden floor first, and then use a vacuum cleaner to aim at the splicing gap of the soaked floor to suck the water vapor away.

3. Hair dryer drying method.

If the floor is less flooded, use a hair dryer to blow through the crevices until it dries. Remember to dry slowly with cold air, if you use hot air, it is likely that the surface will dry out and deform due to heat drying too quickly.