What should I do if the iron section of the electric fan plug is in the socket?

The first thing to do is to buy a two-pin plug and use pliers to plug the broken fan.

Or cut it off with scissors, and then peel off the outer skin of the wire end and install it on a new plug so that the electric fan is done.

You can continue to use it.

The second is to turn off the power supply of the socket first, use a flat screwdriver to insert it into the gap in the middle of the bottom of the socket, you can take off the socket panel, and then use the driver to unscrew the fixing screws at both ends of the socket, and then loosen the wire fixing screws on the interface inside, and you can take off the socket after taking out the thread, see if the back is fixed by the fixing screws or fixed by the plastic buckle, remove the socket core, and then take out the broken plug metal sheet, install and reset the socket and continue to use it.

If the metal piece of the broken plug cannot be removed, it is necessary to replace and install a new outlet.

Prepare a socket of the same specification first, then cut off the power supply, remove the old socket, remember the wiring position, and then install the socket in the original order. It can be used when the power is closed. Then consider replacing the fan plug and the foreign object from the old socket, so that you don't have to worry about time and safety.

Open the back cover of the nose and take a look. If the screws are loose, tighten them. If it is broken, the only way to change it is to replace it with a fitting of the same model.

If you don't understand, you can ask a friend who understands this industry to help you check and repair. You can also ask a professional maintenance personnel to check and repair. FYI.

Disconnect the power from the main switch and get it out.

If the exposed part of the socket is relatively long (more than 1 mm), then you can cut off the electric game such as the large source first, and then pull it out directly with pliers.

If the exposed part of the oak cherry is short and the pliers can't clamp it, then you can only do the insulation first when the power is off, and the insulation will not affect the safe use for the time being.

Just affect the use, there is no safety hazard, you can find one.

Snail Chi Bi wire knife.

Turn the socket on and remove the broken iron. In this way, the socket can be used normally. Pay attention to safety during the Dongdan grinding operation.

Cut off the power supply. Then the screwdriver unscrews. Take it out. On the screwing . . . I really can't use a magnet to suck it out.

Judge whether it is a live line or a zero line first, and then close the valve according to the situation.

Only cut off the power supply first. Then slowly get it out.

Power off the power strip, then remove the strip, take out the chip, and install the strip.

It depends on the situation at the time, if there is electricity when the plug is pulled, it means that there is leakage in the plug contact. If there is electricity in contact with the plug after the plug is unplugged, the reason is that your own body is drier and easy to generate static electricity, and you see if the clothing you are wearing is chemical fiber, and the body can also produce static electricity when wearing chemical fiber clothing for a long time. Sometimes, if the static electricity is too strong, you can feel the sound of being struck by electricity.

Of course, the way is to avoid the above two points, and if it still doesn't work, then you need to use tools. Haha, after the plug is unplugged, it is good to use the driver to contact the lower plug to discharge it. I used to sell electrical appliances and electrical materials, and I also had your problem.

The fan plug is generally three wires, and you can buy a plug to connect it yourself. (live wire, neutral wire, grounding protection wire).

Get more tape in the place to prevent exposure of electricity.

If you have small children at home, it is best to buy them from scratch.

1. There is a transformer room in your community, your wires are powered by this transformer room, there is a large transformer in the transformer room, and the wiring of this transformer is connected to the neutral line and the grounding wire together, and then the neutral line and the grounding wire of the transformer are connected to many distribution cabinets in the transformer room, so that the neutral line and the grounding wire in the distribution cabinet have been divided into two wires, and then a wire is drawn from the distribution cabinet to the distribution box on the wall of your building or floor. Then lead a wire from the wall distribution box including the live wire, the zero line, and the live wire and the zero line are drawn from the transformer room, only the grounding wire is connected from the outdoor underground of your building, that is to say, the grounding wire is connected from the outside of your home, and the earth is the transformer room and your building are on the same land, so the soil of the earth is connected, the zero line of the transformer room and the grounding wire are mixed together, the grounding wire of your home is connected with the earth, and then from the earth to the grounding wire in the transformer room, it is connected. The grounding wire and the neutral wire in the transformer room are the same wire, in fact, the neutral wire and the grounding wire in your home are also connected.

2.However, from the power supply system, you can't lead the grounding wire in the transformer room to your home, you must draw the grounding wire from the outdoor ground of your home (this outdoor grounding is not as simple as a single wire, but a complex grounding system, which is composed of a circle of grounding belts and dozens of grounding electrodes around your home), the reason is to consider the protection of personal safety, to consider the grounding resistance in the grounding system can not be large, if the grounding resistance is large, it will not be able to protect personal safety. It is also necessary to consider the lightning protection of your building, so the grounding wire must be drawn from the outside of your building.

3.When the zero wire in your home is broken, because the grounding wire and the neutral wire are mixed together in the transformer room, although you do not have a neutral line in your home, you can still use the grounding wire as a neutral line. At this time, in fact, the electricity on the grounding line of your home is borrowed through the zero line of other residents in your building, you might as well try it, and disconnect all the zero wires of all the residents in your building, and there will be no electricity on the grounding line of your home, and it will not be used as the zero line.

4.Although your home still has the grounding wire as a zero line to use, but there are sequelae, because, the electricity has passed through your home's grounding wire, and your home grounding wire and the use of the whole building metal parts are connected together, that is, the steel bars in the wall of your building are electrified, in case, when the stainless steel rod of someone's clothes is installed, the expansion bolt just touches the steel bar in the wall, then the clothes rod is electrified, when someone is drying clothes, the hand touches the stainless steel rod, it will be electrocuted, numbness.

5.It will also make the refrigerator shell in your whole building have electricity, the microwave oven shell has electricity, the electric water heater shell has electricity, and maybe the shower room has electricity. In case someone is electrocuted, it's a big problem.

6.So. The state stipulates that it is strictly forbidden to use the grounding wire as a neutral line.

The ground wire is to avoid electric shock, equipment static electricity, in order to improve the reliability of the product. Nothing can be used, just not that safe.

First of all, it is certain that your fan has a great safety hazard, the zero line is broken, and the current flows out from the live wire through the fan through the ground wire, if the person unintentionally touches the metal shell of the fan or other electrical appliances in use, such as the water heater, it may be electrocuted. So you can't use such a fan anymore, it's very dangerous.

Because n is the ground wire, the ground wire is connected to the earth, if the outer skin of the leakage electric fan is grounded, there will be no leakage electricity. It will not affect the working of the electric fan.

The neutral wire is a grounding wire to avoid electric shock, and it can work without electrical appliances, but there is a risk of electric shock.

The ground wire can be used as a neutral wire temporarily

In view of your problem, since the power supply voltage of our fan is 220V. He also has a ground wire. Therefore, the voltage between the live wire and the neutral wire and the ground wire is 220V.

Some devices are connected to the neutral wire and the ground wire. Ground zero is not separated they have voltage. Try to use the neutral wire to prevent electric shock.

Hope it helps, it's just a personal opinion.

The ground wire is used as a neutral line.,It's very dangerous.。。

Originally, there was no grounding on the three-phase socket or anything, so wouldn't it be used the same?

It is necessary to check to know what is broken, and generally there will be capacitor failure, switch failure, and motor winding burning.