The floor tiles at home are swollen, how should I deal with myself?

Tile is not completely loose: in this case, the difficulty of treatment lies in the removal of the tile, which may cause damage to the tile, which may involve the replacement of the damaged tile"Glue high-grade cement slurry 3 cm thick, homeopathic put in"Inside the brick cave.

If the tile is left jointed and warped for maintenance, this situation does not need to be worried. If there are no seams in the tiles, and you are afraid of other warping, it is best to ask someone to cut all the gaps of the tiles by 2 mm, so that the tiles will not warp. Most of your problems are caused by the original tiles without leaving seams, the reasons are:

Tiles also have thermal expansion and contraction, which is the same as that of wooden floors, and it is easy to arch and fall off if there are no gaps. If we find that the tiles on the floor of our house are only partially bulging. At this point, we don't need to treat a large area, we only need to treat the bulging tiles.

Regarding the problem of how to repair the floor tiles bulging, the home miscellaneous altar has proposed two solutions for everyone. One is partial repair, the other is complete repair, you can choose according to your own situation! The basic situation is caused by the heat expansion and contraction, no matter what the reason, removing the old floor tiles and resurfacing is the best way to solve the problem.

This is more difficult to deal with, if you directly remove the floor tiles, it is likely to cause damage to the floor tiles, if damaged, you can only replace the floor tiles, but it is not so easy to find the same on the market. The quality of the tile itself, there may be a problem with the water absorption rate of the tile or the tile has a bowed back problem when the tile leaves the factory, and there is a hollow drum phenomenon at the cement mortar below the paving. Since the floor tiles are protruding, you can only take off the bricks, clean the bricks and the ground, apply them evenly on the ground with special floor tile glue, and hammer them with a leather hammer.

Try sprinkled with cool water every day to prevent the temperature from rising or open the windows for ventilation, which is basically not too noticeable.

The floor tiles at home are swollen, how should I deal with myself? If it is not serious, paste it with floor glass glue, try to stick it in two directions first, stick it in four directions if it doesn't work, and buy an identical floor tile for paving; Then lift the floor tiles, clean them, pour cement slurry, and re-pavement; If the floor and the original fit are relatively tight, find some waste grinding wheels to grind.

Personally, I think that if the floor tiles in my home are swollen at this time, I must treat them professionally at this time, and remove the floor tiles when necessary.

You can spread ice cubes on it to cool down, expand and shrink the heat, or you can sprinkle it with cold water, ventilate the windows, etc.

When choosing floor tiles, it is important to consider the following aspects: First, it depends on the brand. Only well-known brands of floor tiles, the quality of their building materials can meet the national standards, and the content of harmful substances can be within a safe range.

Second, it depends on its anti-pollution ability, if the family is very busy and can only clean once in two or three days, then choose the one with better anti-pollution ability. Third, if there are elderly people and children at home, you must do a slip resistance test when purchasing.

Specifically, the selection of floor tiles can start from the following aspects:

1.To see if the color of the tile is pure. Mainly observe whether the color of the back of the tile is uniform and consistent.

2.It is necessary to observe whether the particles of the cross-section of the tile are fine. The cross-section here does not refer to the cutting surface around the tile, but to the fracture of the tile fragment.

Generally speaking, the fracture is fine, hard and brittle, and the color is the same. Because the ceramic tiles with fine particles have strong waterproof ability, while the tiles with large particles are easy to soak in moisture, which affects the quality.

3.Pay attention to the thickness of the glaze layer. The thickness of the glaze layer is the thickness of the cross-section of the glaze. Glaze is the most expensive material in the cost of ceramic tiles, and the thicker the glaze, the better the quality.

4.To listen. Tap the tile to pay attention to whether the sound is crisp, such as the sound is clear and pleasant, such as the sound is dull, it is inferior.

5.Test the waters. Consumers can pour some water on the back of the tile and pay attention to how quickly the tile absorbs water. After a few minutes, see if the marks left by the water on the front are obvious. The density of tiles that infiltrate slowly after the water disperses is large, and the marks left by the water are not obvious, so they are regarded as the top grade.

6.Warp. Take two bricks back to back and face to face to see if they can be in close contact, and there is no phenomenon that the gap is too large to judge whether there is warping.

7.Infiltration. Find ink to apply to the surface for 1 hour and then scrub to see if there are traces, no traces are good bricks, and those that have infiltration are resolutely not selected.