What is the reason why there is no water in the toilet pit?

The landlord said that there is no water in the pit, and we generally understand that the toilet has no water seal.

Because the toilet drain is bent, it will form a water seal and store water permanently. If the water seal is gone, it must be trachoma in the drainage pipe.

or some other reason that caused the water in the water seal to leak. This is not the case with brand-name toilets.

First, if it is leaking from the bottom of the toilet after flushing the toilet, and the water is not clear and has a peculiar smell, then it can be basically judged that the sealing ring on the drain pipe at the bottom of the toilet is not sealed, and the sealant on the edge of the toilet and the ground is not tightly sealed. This phenomenon mostly occurs shortly after the toilet is installed. Second, if it is found that there is water seepage from the surface of the toilet at any time, then it is suspected that there may be cracks in the toilet, and the inspection method is:

Turn off the inlet valve first, then drain the water in the toilet tank, and then add red ink or colored ink to the water remaining in the tank, stay for about 30 minutes, and observe whether there is colored ink in any place, if there is, you can conclude that there is a crack in the toilet, which cannot be repaired, even if it is repaired, it is also a problem toilet, and the only way is to replace it. Third, there is another situation that the toilet tank can not store water, which can occur in two situations, one is the problem of water parts, you can repair it, see if the leather cushion is loose, if there is no way, you can only change the water parts; Another situation may be that there is a crack in the inside of the toilet, and if the water is fine, it can be detected from the second method.

One is that the toilet trap is leaking, and the other is that the toilet is straight out.

There are reasons for this; 1. The toilet does not store water because the water storage tank is faulty.

The main reason may be the aging of the rubber gasket of the water discharge system or the impurities at the sealing gasket and the poor sealing of the gasket.

2. The toilet water storage tank is mainly composed of two parts: the water inlet and the water discharger.

When the drain fails, the water cannot be stored, the water inlet is always inlet, and the drainer is discharging water at the same time.

3. There is also a possibility that the flush button is malfunctioning.

4. Repair method: If you don't understand, ask the hydraulic master to repair; If you know a little bit about repair, you can repair it yourself - tighten the water drainer, so that the mat under it is tight, and it will naturally not leak, and if it doesn't work, you need to check whether the mat is damaged, and replace the mat in time.

Expand your information;

Here's how a flush toilet works:

Use the drain knob and plug to control the discharge and storage of water.

When using, rotate the water discharge knob, use the metal rope or nylon rope connected to the water plug to pull up the water plug, pull the water plug upwards out of the outlet pipe port, and the water outlet pipe puts the water into the urinal, and uses the gravity of the water and the kinetic energy converted by potential energy to flush the excrement into the sewer pipe.

At the same time, when the water level drops to a certain water level, the negative pressure generated by the gravity of the water will re-press the water plug into the port of the outlet pipe, block the water outlet, and then the water will no longer be released and start a new water storage stage;

When the water level drops, while flushing the urinal, the float together with the lever is driven by the gravity of the float due to the drop in the water level, and the lever is opened to start synchronous water replenishment; In the water replenishment stage, the buoyancy and lever of the float are used to control the water replenishment of the water tank, and when the float descends to the lowest position, the water plug is pressed into the mouth of the water pipe by negative pressure, and the water tank begins to store water.

The water inlet pipe is connected to the water pipe, which is responsible for the input of the water source, and when the water supply reaches a certain height, the buoyancy of the water will lift the float up to the linkage lever, close the water supply mechanism, and stop the water supply.

When the inlet pipe leaks due to a malfunction (e.g., the inlet plug fails to block the inlet or the inlet pipe breaks), the water level in the tank will continue to rise and eventually overflow the tank. And the setting of the seepage pipe solves this problem.

When the water level rises to the seepage nozzle, the water flows into the toilet bowl from the seepage pipe and does not allow the water to overflow the tank.

When the inlet pipe is working normally, the water surface in the tank will not reach the seepage nozzle, so there is no need to worry about the water flowing away.

Reference Links; Encyclopedia - The principle of the water tank.

Abstract The toilet tank can not store water, which can occur in two situations, one is the problem of water parts, you can repair it, see if the leather cushion is loose, if there is no way, you can only change the water parts; Another scenario may be that there is a crack in the inside of the toilet.

What is the reason why there is no water in the toilet pit?

The toilet tank can not store water, which can occur in two situations, one is the problem of water parts, you can repair it to see if the leather cushion is loose, if there is no way, you can only change the water parts; Another scenario may be that there is a crack in the inside of the toilet.

Not a water tank! It's the toilet pit that can't hold water.

Open the back water tank and take out the water parts to clean up, which should be caused by impurities.

Not a water tank! It's the toilet pit that can't hold water. When flushing, it will all run dry.

It is necessary to check whether there is a fault in the button to press the water, so that the water has been released inside, and there is no water in the pit. The solution is to tighten the drainer first, check whether the gasket inside is worn, if so, you need to replace the new gasket in time.

There is no water in the toilet pit, mainly because the water storage tank is faulty, and one of the sealing gaskets in the water discharge system is aging or worn, which will lead to poor sealing and water storage. It is also possible that the water drain is faulty, and the water inlet keeps discharging water, and there is no water in it.

Summary. The reason why the toilet pit can't store water in the toilet pit is because there is a guide rod on the upper part of the ball, and the guide rod is often pulled, causing the guide rod to be skewed, so if it falls down again, it will be sealed loosely and cause water leakage, and it is recommended to correct the guide rod. The rubber valve that plugs the leakage is aging and deformed, and the plugging is not strict, and it is replaced with a new rubber felling.

What is the reason why there is no water in the toilet pit? ↘

Hello, welcome to use to know, happy to have your question, don't worry, is inquiring for you.

The reason why the toilet pit can't store water is because there is a guide rod on the top of the ball, and the guide rod is often pulled by a sharp loss, causing the guide rod to be skewed, so when it falls again, it will be not tightly sealed, resulting in a leakage branch premature phenomenon, it is recommended to correct the guide rod. The rubber valve that plugged the leakage is aging and deformed, and the plugging is not strict, and it is replaced with a new rubber felling.

Dear, if you think mine is helpful to you, please give a like! If you have any other questions in the future, you can click on my avatar to consult me about Pants Boxiang, and I will definitely give you the most satisfactory Hu Bo.

There are several possible reasons why there is no water in the toilet pit of the new toilet:

1.Unreasonable design: Some new toilet oaks are designed with smaller water tanks, lack sufficient hydraulic flushing, and cannot form a strong water flow when flushing, and cannot form a vortex pin hand suction, resulting in no water storage in the pit.

2.Dirt accumulation: Due to the length of time the toilet is used, it is easy to cause dirt accumulation, resulting in a change in the shape of the toilet pit or a blocked pipe, so that the water that should be stored in the toilet pit cannot be trapped in the toilet hole.

3.Water level height problem: If the toilet drain is not properly designed, the position of the drain does not match the water level in the toilet, which will make the water level in the toilet too low, and then make it impossible to accommodate feces at all.

4.Anti-odor problem: Some new toilets are deodorized for the beam, and a feeder is installed, after mixing disinfectant, oxygen and other substances, the liquid will sink into the bottom of the toilet by itself, forming a stable thin liquid layer, after a certain period of time, a certain amount of gas will be automatically generated, so that too much water can not be stored in the pit.

5.Pipe problems: The angle and diameter of the pipe between the toilet bowl and the drainage pipe are important factors affecting the height of the water level in the pit, if the angle is not vertical and the pipe diameter is not suitable, it will affect the drainage efficiency, so that the pit can not store water.

In short, the above factors are the reasons why there is no water in the toilet pit of the new toilet, and we should check and clean the toilet regularly to ensure its normal use.