Is it better to have a wall hung stove with floor heating or a radiator

Radiators and floor heating have their own advantages and disadvantages, there is no better, you can only choose the heating method that suits you, the following is a brief introduction.

1. The installation conditions of radiators and floor heating are different.

Radiator installation: more inclusive, whether it is a new house decoration or an old house upgrade can be met, and there is no requirement for floor materials and insulation conduits, just choose the right height and sufficient amount of radiators according to the family space area. As long as there is no large piece of furniture around the radiator to block the heat dissipation, it is fine.

Floor heating installation: The floor heating system is a concealed system, and all pipes are buried in the ground, so it is necessary to design and construct in the early stage of house decoration, which is suitable for new houses without decoration. Moreover, the floor heating will occupy a floor height of about 4cm after being backfilled with dry and wet paving, which will reduce the net height of the room, and the room type with insufficient space height is not suitable for using floor heating.

And after the installation of floor heating, the purchase of the floor also needs to pay more attention, small thermal resistance, low water absorption, small expansion and deformation of ceramic tiles, marble floor materials are more suitable for floor heating families.

2. The heat dissipation effect of radiators and floor heating is different.

Radiator: The heat dissipation method of the radiator is mainly based on air convection, which heats the air around the radiator first, so that the hot air forms convection in the room, so as to achieve the purpose of heating. Therefore, the radiator heats up quickly, and the heating system can reach the preset temperature within half an hour of opening, which can basically be used immediately.

Floor heating: The heat dissipation method of floor heating is radiant heat dissipation, which radiates heat through the hot water in the floor heating pipe, and then conducts upward heat dissipation by the floor. Underfloor heating pipes are located throughout the rooms, so the temperature difference in the room is small.

However, due to the large specific heat of the water, coupled with the need for floor conduction, the floor heating rate is slower, especially when it is turned on for the first time, and it takes a while for the whole room to heat up. In the same way, the floor heating heats up slowly and cools down slowly, and the floor and concrete layers have a strong energy storage capacity, so they can keep the room temperature stable even if they run intermittently.

3. The comfort of radiators and floor heating is different.

Radiator: Because the radiator uses air circulation convection heat dissipation, the room temperature is hot and cold, the closer to the radiator, the higher the temperature, the room temperature gradient changes significantly, and the comfort is different from floor heating, but the room temperature difference can be improved by increasing the number of radiator groups.

Floor heating: The uniform heating method of floor heating from bottom to top is conducive to blood circulation and is suitable for installation in families with elderly and children.

Let me tell you about the respective advantages and disadvantages of underfloor heating and radiators. Use it in what situation it is suitable for.

With underfloor heating, underfloor heating heat dissipation is from the bottom up. It is more comfortable on the feet and easy to get angry, and it is not suitable for people who are afraid of dryness. The higher the degree of dryness is higher than that of radiators.

Drink plenty of water or humidifiers, suitable for clean household use, or there is always floating dust in the air that is absorbed by others. Troublesome maintenance, not suitable for solid wood flooring, to use laminate flooring. The requirements for flooring are also relatively high.

The initial installation cost is higher than that of a radiator.

The radiator feels comfortable as a whole, and you have to wear slippers to keep your feet cold. The dryness should be low and suitable for any household use, and the radiator on the surface of the wall is easy to repair and maintain. It mainly relies on radiant convection to dissipate heat.

The initial installation cost of radiators is lower than that of underfloor heating. Long service life. It's much more comfortable to use than an air conditioner.

The calorie consumption is the same, and the calories cannot be changed.

Underfloor heating and radiator heating each have their own benefits, but wall-hung boilers.

If you want to, you can consider a copper-aluminum composite radiator, which heats up relatively quickly and is suitable for phased heating, Rubens.

Heating hope it helps you.

Radiators are better than installing radiators for the following reasons:

1. The installation of radiators is simpler, and the radiators installed in homes are basically installed on the wall. The common installation location is basically made of a certain wall in our room, for example, the living room is generally on a certain wall in the living room, if there is a window in the bedroom, it is generally on the lower side of the window, and it can be installed directly on the wall in the kitchen or bathroom.

2. From the perspective of later maintenance, the radiator is also simpler, for example, after a few years of heating at home, there may be a slight leakage, if it is the leakage of the radiator, it can be easily repaired. But if there is a leak in the floor heating, the pavement layer of the ground needs to be removed, if the ground is paved with tiles, the tiles should be removed, and then the concrete will be smashed open, revealing the floor heating pipe inside, so that it can be repaired.

Precautions for the use of radiators

1. Avoid changing the position of the radiator at will.

The installation position of the radiator is generally designed and installed through door-to-door measurement, and is arranged in a position conducive to indoor heating according to the user's house situation, which can ensure that the air convection and indoor temperature are relatively average, and once the location is changed, it will cause an imbalance in the indoor temperature. And once the pipes and radiators are displaced, there may be water leakage, causing unnecessary losses.

2. Avoid blocking the radiator.

In order to ensure that the radiator dissipates heat well, try to ensure a certain amount of heat dissipation space around it, and do not pile up sundries. Do not block the front of the radiator with a sofa or cabinet to avoid damaging the furniture. It is best not to cover the periphery of the radiator, excessive decoration not only affects the heat conduction and air convection, reduces the heating effect, but also is not conducive to the timely detection of the use of the radiator.

3. Avoid piling heavy objects on the radiator.

The weight of the radiator is limited, do not put too much heavy objects on it, and it is best not to use it as storage and stacking sundries in the non-heating season. In daily life, it is necessary to avoid the radiator being squeezed and bumped by heavy objects, so as to avoid water leakage caused by distortion and deformation of the internal pipes.

There are three types of household heating, floor heating system, radiator system and mixed system (that is, floor heating + radiator), each with its own advantages and disadvantages, I will compare floor heating and radiators, the third mixed system is the combination of floor heating and radiators, which is the most perfect heating system.

Radiator: Speed: It only takes 10-30 minutes to turn on the heating up.

Energy consumption: Low energy consumption in areas with large temperature changes (such as Hunan).

Comfort: Foot comfort is lower than underfloor heating, but the temperature fluctuates less depending on the air temperature.

Floor: Mounted on the wall, the floor can be made of any material.

Cost: The cost of the system is higher than that of floor heating, but there is no backfill, and the overall cost is low.

Ceiling height: A suitable flat floor room, used in a house with higher space, consumes more energy than underfloor heating.

Suitable for: Radiator heating is suitable for office workers.

Floor heating: speed: turn on the heating slowly, at least 5-6 hours.

Energy consumption: Energy consumption is higher in areas with large temperature changes (e.g. Hunan).

Comfortable: Comfortable on the feet, but the temperature fluctuates greatly depending on the air temperature.

Floor: Wooden flooring seriously affects heat dissipation, suitable for ceramic tiles and stone floors.

Cost: The overall cost (system + backfill leveling) is high.

Ceiling height: Used in rooms with high space, it is more energy-efficient than radiators.

Suitable for: Floor heating is only suitable for the living room and dining room, or the high ceiling space; It is not suitable for whole house installation (whole house underfloor heating: it is not comfortable, it is not energy efficient, and the initial investment is also high, so it is the worst heating system).

Some people will question that the temperature of floor heating will fluctuate greatly due to the influence of air temperature: floor heating has extremely unstable characteristics when the temperature changes, and the floor heating water capacity is large, when the temperature rises, even if the system has stopped, the heat storage layer (concrete, floor) still continues to absorb the heat in the floor heating pipe and release it into the room, so the room temperature will rise sharply; As the heat from the regenerator is released, the room temperature drops below the set comfortable temperature; When the system starts heating, it doesn't start to heat up until the regenerator is heated and starts to release heat.

Finally, it is recommended that you do a mixed system:

Comfort: Commonly used (or high-rise) rooms are heated under floor heating, which makes your feet feel comfortable;

Energy saving: Room radiators that are not commonly used can be turned off to save energy;

Stability: There is no thermal storage layer in the room without floor heating, which can buffer the unstable characteristics of floor heating due to temperature changes;

Cost: 20%-30% higher than underfloor heating, 5%-10% higher than radiator system, need to backfill cost.

Floor heating is laid in the area where people stay for a long time, and radiators are installed in the rooms that do not stay for a long time, which is the most perfect heating system to adapt to the vast majority of people and house types.

In fact, no matter what system you do, choosing a reliable and professional heating company is the top priority.

Is underfloor heating or radiators better?

Floor heating is good, but there is an additional cost, and now the hanging heating is also more fashionable, and it is also very good-looking, and it will not affect the beauty to find a suitable decoration style for yourself.

Do you have a heating in your home? Whether it is floor heating or radiators, which one is better? Let's focus on the difference between heating and floor heating, and you can consider and choose according to the actual situation.

Personally, if you have elderly people and children at home, if you are newly renovated house, it is recommended to give priority to underfloor heating. The benefits of underfloor heating are more obvious to the family. I saw this in Chengdu Qichang HVAC**, and I forgot about it.

If you are an old house, or have been installed, then you can only choose to install radiators, my home is installed floor heating + radiators, because the house is relatively large, so the choice of the combination form, the elderly and children's room must be floor heating. What to choose for this is actually based on your own needs.

In winter, for household users who do not have universal central heating, more and more people will choose to install independent heating heat source wall-hung boilers for heating. Because the wall-hung boiler can not only be used as heating for the whole family, but also can meet the user's demand for domestic hot water. However, there are many people who are always hesitant between radiators and floor heating after buying a wall-hung boiler, and do not know whether the wall-hung boiler is more suitable for floor heating or radiators, and which is more cost-effective between floor heating and radiators.

Let's follow the golden flagship flag brother to find out.

On this issue, we have to divide it into two layers, mainly divided into the early installation cost and the later use cost. So let's go with the HVAC expert Senlat to see which is more economical with a wall-hung boiler with floor heating or radiators!

1. Comparison of pre-installation costs.

1. The installation of radiators is relatively simple, and the purchase cost is not too high. Under normal circumstances, a 100-square-meter house needs about 30 pieces, taking the copper and aluminum radiators on the market as an example, a copper and aluminum radiator is about 200 yuan. Comprehensively calculated, the installation cost of the radiator is between 4500-6000 yuan.

2. The floor heating composition mainly includes floor heating pipes, water collectors, ground auxiliary materials, thermostats and some elbows and other accessories, each of which requires cost, the same 100 square meters of the house as an example, the domestic floor heating pipe is about 90 yuan per square meter, and the joint venture and imported brand ** are relatively expensive, about 120 yuan - 200 per square meter. Coupled with the manual installation fee, in general, the installation cost of floor heating is about 10,000 yuan.

2. Comparison of later use costs.

1. The radiator is heated when it is opened, and if you want to achieve the most comfortable heat dissipation, the hot water needs to reach 65 --70, which means that the early consumption of the wall-hung boiler will be relatively large, according to the calculation, the average 100 square meters of the house, the use of the radiator for a month will cost about 1200 yuan. Of course, the HVAC expert Senrat needs to remind everyone that the radiator is immediately hot, and it is generally not open 24 hours a day, so the gas consumption has also been reduced.

2. The heat dissipation of floor heating is relatively slow, and the water temperature required for floor heating is generally 45, so the consumption of wall-hung boiler is much lower than that of radiators, and the monthly cost is generally about 900 yuan for a house of the same area. However, in some areas, such as Hangzhou, there is a ladder for calculating the amount of floor heating consumption, and the larger the area, the higher the cost.

Jinsheng late return gold suggests that users with a home area of less than 150 square meters or you have elderly children or family economy is enough, floor heating is definitely the best choice. Because the floor heating heat dissipation meets the needs of the human body, it is more comfortable, and the most important thing is that the later consumption is lower than that of radiators.

All suitable. The key is whether you are suitable for underfloor heating or radiators?

It depends on the local temperature, if the day is below zero, it is recommended not to care, adjust the wall-hung boiler to the lowest temperature, if the local temperature is above zero, and there is no one at home during the day, it is recommended to close it well, one is to cost natural gas, the second is unsafe, and the third is that after all, it is always open for the wall-hung boiler is also a loss. If there is no one by chance, it is recommended not to turn it off, just keep the original temperature, because the wall-hung boiler itself is automatically adjusted, when the indoor temperature reaches its rated value, the wall-hung boiler will automatically close, and when the temperature is lower than its rated value, the wall-hung boiler will automatically open. This is my own personal experience.

Wall-hung boiler heating, the heat consumption of natural gas is determined according to the heat load of your room, you should look at your housing area and the power conversion area of the wall-hung boiler to choose, there is a margin is the best, the power of the wall-hung boiler is a little larger to avoid not enough, in order to save gas consumption, you should do a good job of indoor insulation, do a good job of control setting of the wall-hung boiler, and the heating temperature is comfortable as the standard.

It is perfect to make a double system with a wall-hung boiler! The wall-hung boiler was used for heating for two months before and after the central heating, and it was very convenient to switch to the past after the central heating came. I've been at home for 6 years.

I think it's very reasonable. The floor heating waterway at home is closed, and after the centralized heating comes, the waterway at home is also exchanged through plate exchange, so the waterway at home is always clean. I don't know how to make a wall-hung boiler or know how to change the board.

The professional manufacturer brands of wall-hung boilers are: Vaillant (German brand, high-end quality, high after-sales service, pure imported production in Turkey), Bosch (German brand, leading technology, imported production in Turkey, Shanghai also has a production line), Viessmann (German brand, boiler starts, HVAC also has leading technology, good quality), Ariston (Italian brand, Wuxi has a production line), Yima and other foreign brands are relatively high-end, leading.

The domestic wall-hung boiler brand has developed and expanded rapidly in recent years (due to the pull of the national coal-to-gas policy), and the domestic brands with excellent sales and technology are: Little Squirrel, Wanhe (the first in China, with a professional laboratory), Smax, etc. In addition, installation is crucial to the use of wall-hung boilers, and you must find a professional HVAC master.