What happens when a rubber tree doesn t germinate after topping?

What should I do if the rubber tree does not have side branches after pruning and topping? If you continue to hit the top, you can hold out the side buds, don't feel distressed for the sake of styling!

The rubber tree is a relatively easy to maintain plant, but the ability to germinate is too low, and it is extremely difficult to grow branches without human intervention. After the rubber tree is topped, it can break the supply and demand of nutrients and force out new side branches. But topping and promoting branches need to be done at a specific time.

Insufficient nutrients are also the main reason why rubber trees do not germinate when they are topped. The indoor ventilation is not good, and many people are afraid of the peculiar smell of fertilization, so they rarely fertilize the rubber tree. In addition, the potting soil is used for a long time, and the nutrients are depleted.

It should be a lack of nutrients in the plant, nitrogen and potassium fertilizer should be supplemented in time to promote the growth of plant rhizomes, regular watering and placement in a ventilated place.

The main reason for not germinating is likely to be that there is only a problem in the middle, and then there is not perfect light, so the lack of water in this case causes the phenomenon of not germinating.

If not pruned in time, the rubber tree will grow upwards vigorously, and the trunk will become thin and tall, without beauty. However, pruning a rubber tree also requires some small skills, and random pruning may not achieve the desired effect, and it may even be difficult to grow new shoots.

It is rare for rubber trees to still do not germinate side buds for a long time after topping or pinching, but they do occur from time to time. If the rubber tree has only stems and no side branches, it is usually only necessary to top the stems to force the side buds out and form side branches. If you want the plant to continue to germinate more side buds, you usually need to continue topping the side branches when they grow to a certain length.

Until there are more side buds that have sprouted and new side branches have been formed to make the plant plump enough. However, if the upper part of the stem of the plant is already branched, and if we do not grow lateral buds after removing the tip of the stem, then we need to continue to top these branches. After several topping treatments, the plant will eventually sprout lateral buds.

Hello! Rubber leaf cuttings do not sprout when they take root, which should be the wrong method.

Eraser leaf insertion method:

1. Choose one-year-old healthy and stout rubber tree leaves, choose a leaf with axillary buds as cuttings, cut it with a sharp knife against the trunk, leach it with warm water or dip it in charcoal powder or absorb the milk flowing out of the incision before cutting, and then cut it.

2. The selection of leaf cuttings substrate is best to use vermiculite, which has a high survival rate.

3. You can use flower pots to make slotting beds, if not, you can also use Coke bottles to make a simple one, only need to make a few water outlets at the bottom and side to drain it.

4. When the bed is ready, you can insert the dried rubber tree leaves into the substrate, and then water them thoroughly.

5. In the process of seedling growth, we should pay attention to maintenance, and after changing into a large pot, we should properly fertilize and pluck the tops and dry them in a timely manner to promote the flourishing of branches and leaves.

affect ornamentality; And choose too low, because the branches at the bottom are not easy to germinate, which is easy to cause the problem of not germinating after toppingSo if you have just repotted a rubber tree, can you top it? It is possible to top. There is usually nothing wrong with this.

Secondary topping: Rubber tree.

After topping, only one side bud grows, and the side bud should be cut off. Thin fertilizer diligent: apply potassium dihydrogen phosphate once a month.

Or well-rotted organic fertilizer. Science sees the light: Place the rubber tree in a well-lit environment. Repotting: Replace pots with more space and fertile nutrient soil.

1. Secondary topping

It is necessary to wait for the side buds of the rubber tree to grow to 10 cm before topping it a second time, using sharp and sterilized scissors to cut the side buds of the rubber tree from the branches.

2. Apply thin fertilizer frequently

Rubber trees need sufficient fertilizer in the growth process, when breeding rubber trees, you need to apply fertilizer once a month, you can choose rotten organic fertilizer or nitrogen, phosphorus and potassium compound fertilizer, so that its growth rate is faster, and spray potassium dihydrogen phosphate on the leaves of rubber trees.

3. Science sees the light

Rubber trees like light, when cultivating rubber trees, it is necessary to place the plant in a bright environment, let it receive no less than 7 hours of light per day, promote the photosynthesis of the rubber tree, make it grow new leaves quickly, and when the light is insufficient, you need to use plant fill lights.

4. Turn over the pot and change the soil

If you want the rubber tree to grow vigorously, you need to replace it with a larger pot, which is conducive to the growth of the root system of the plant, it is best to choose a porous clay pot or a mud pot, and use sandy soil, humus soil, and garden soil to mix into nutrient soil, and then plant the rubber tree into it.