What are the steps and methods of wallcovering?

Updated on home 2024-07-25
11 answers
  1. Anonymous users2024-02-13

    1.Check the quality of the wall: Before pasting the wallpaper, be sure to check the condition of the wall, in general, only if the wall meets these three conditions:

    When the wall is dry, flat, and the pH is moderate, you can start laying wallpaper. If the wall has been painted or treated with moisture, it should be allowed to dry for 15 working days before starting to be laid.

    2.Do a good job of ground protection: Before laying wallpaper, you also need to protect the ground, you know, when laying wallpaper, you need to use glue, so you need to lay a layer of protective film on the ground in advance, such as plastic film, so that when laying wallpaper, the falling glue will not stain the ground.

    3.Measure the area of the wall: Paste the wallpaper is not a one-stop paste on the wall, you must measure the size of the wall in advance, so as to know how much wallpaper is needed for paving.

    4.Crop the wallpaper: After measuring the area of the wall in advance, you can cut out the corresponding size of the wallpaper.

    However, it should be noted that the size of the cropped wallpaper needs to be about 10cm more than the length of the wall, and the extra wallpaper should not be thrown away, it may be used later.

    5.There is another problem to note, if there is a beam in the middle of the wall, then when pasting the wallpaper, you should bypass the beam and only paste the part of the wall without a beam, so that the effect will be better.

    6.Wallpaper glue softening: In order to make the wallpaper and the wall tightly fit together, the wallpaper needs to be glued. First, use a professional tool to evenly apply the glue to the back of the wallpaper, then fold the wallpaper in half and let it sit for a while (soften).

  2. Anonymous users2024-02-12

    Steps and methods of wallcovering. Not everyone will need the driver's observation, but also need the hope of learning.

  3. Anonymous users2024-02-11

    1. First of all, you need to prepare tools to clean and clean the dust on the wall, and make sure that the wall is neat and clean, and there is no falling wall skin and excess dust, so that the wall cloth can be better pasted.

    2. Put the glutinous rice glue pasted with the wall cloth in a container for full stirring and complete dilution, and then use a brush to search and evenly apply it on the wall, do not apply it in a large area, only need to apply it in a small area first, and then continue to apply it after the ruler is constantly pasted, so as to prevent the watering time from drying out for too long, resulting in no stickiness.

    3. After applying the glue, you can paste the wallcloth on the wall, in the process of pasting, you must be careful, do not let the wallcloth come out of the closed core of wrinkles and bubbles, you should deal with it by hand in time, and finally wipe the wallcloth evenly.

  4. Anonymous users2024-02-10

    One: apply the glue to the wall, cut it according to the size, and then apply a uniform layer of glue on the wall, pay attention to be even, do not apply glue on the wall cloth, if it accidentally gets on the wall cloth, wipe it with a damp cloth in time.

    Second: the selection of adhesives should be correctly pasted with super glue when pasting wall coverings, and to ensure the green of the overall decoration, we must choose glue with a high level of environmental protection.

    Three: The wall cloth must not be soaked in water before being posted.

    Four: pay attention to the flowers, everything should be stacked and spliced and cut on the wall cloth, remember to flower from the middle of the wall to ensure that the wall cloth paste to achieve the best decoration effect.

    Five: the edge of the wall cloth must be firmly rooted in the bush, there will be gaps when pasting, if the treatment is not good, it will affect the overall effect, so it needs to be fixed with a roller, otherwise it will not only affect the appearance, but also cracks.

    Six: to ensure the cleanliness of the wallcovering, not only to ensure that the wallcloth is clean, but also to see whether the workers' hands are clean.

    Seven: keep the wall cloth naturally dry in order to avoid the wall cloth has warped corners, cracks, etc., to ensure that the wall cloth is naturally dry, which requires all the windows to be closed within 2 days after the paste, in order to prevent natural wind from entering, and at the same time it is strictly forbidden to use air conditioners, dryers, electric fans, etc.

    Eight: clean up the glue and foam check that the wall cloth is pasted with a wet towel to wipe off the excess glue, but also check whether there are bubbles, there are bubbles that can be sprayed with a needle, or use a syringe to glue in the foam.

    1. There are pairs of flowers that are overlapped and sewn, and the flowers should be faced from the middle wall to achieve good results.

    2. Apply glue on the wall to prevent the glue from sticking to the wall. If you accidentally spill it, wipe it off with a damp cloth.

    3. In order to achieve a good stitching effect, the side seams should be pressed tightly with a pressure wheel, otherwise the wall is prone to cracks after drying.

    4. Ensure that the surface of the wall is clean when pasting, and the workers' hands should be kept clean.

    5. Don't let the grease get on the wall covering.

    6. During the construction period, all doors and windows should be closed within 2 days after construction. Allow the wall cloth to stay dry.

    The above is the steps and methods of sticking wallcoverings and the relevant content that should be paid attention to when pasting wallcovering, I believe everyone has an understanding of these contents, I hope this article can give you some help.

  5. Anonymous users2024-02-09

    1. Check whether the wall surface is clean and flat before pasting the wall covering, and the surface of the wall skin is not loose and falling off.

    2. For special tools for wall covering, it is best to use a professional wall cloth knife.

    3. Brush the wall base film on the wall first, and adjust the wall cloth glue in proportion. 2 kg of glue is added in batches. The first time do not add water, stir well.

    The second time, start to add kilograms of water, stir well, and then add glue powder and stir well. Add kilograms of water for the third time and stir well. Add the remaining water for the fourth time and stir well.

    A bucket of glue can be glued to 25-30 square meters.

    4. After the base film is dry, start to roll and brush the wallcloth glue from a certain corner of the wall, generally press the roller brush on a wall, and start to paste the wallcloth after rolling up and down evenly.

    5. Straighten the wall cloth along the wall, the upper height is the same as the height of the wall, and the lower end uses an item to pad the whole roll of wall cloth on the upper part of the baseboard.

    6. Roll the wall cloth and paste the wall cloth on the wall with a scraper, the order is from the inside to the edge, and then continue to pave the wall cloth in this order after pasting it up and down.

    7. If the yin angle is straight, it can be continued without cutting, and the above rolling construction. If the yin corner is not straight, the wall cloth can be lapped and cut at the yin corner.

    8. Measure the length from the yin angle to the yin angle, leave a little room to cut the wall cloth, and straighten the two ends from top to bottom, from the inside to the edge.

    9. Use a clean, wet towel to wipe off the excess glue around the wall cloth.

    10. After pasting the wall cloth for a comprehensive inspection, it is found that there are bubbles and bubbling with a household steam iron.

  6. Anonymous users2024-02-08

    There are many tips for sticking wall coverings, how should wall coverings be pasted?

    First clean the foundation of the wall, then scrape off the greasy, wait until the wall is dry, and then polish the wall smooth and clean, and then apply the base film to protect the wall not easy to get wet, play the role of alkaline sealing, and replace the wall in the future is not easy to break. The walls are painted with latex paint and must be coated with a layer of floor paint before the wallcovering is applied. Latex paint absorbs water well, so it can't be applied to the wallcovering.

    The concentration of floor paint is the floor paint group plus two barrels of thinner. Construction points: The wall should be dry, smooth and clean, and it is best to apply a layer of base film.

    Before pasting the wall covering, be sure to clean the site well. Because the area of the wall cloth is large, it is not dirty. It is best to use an imported utility knife for cutting wall coverings.

    The sharper the wall cloth knife, the more uniform the operation, and there is no phenomenon of dragging mud and water. When encountering silk, never pull it by hand, cut it with a knife.

    Open the rubber powder and special glue packaging for wall covering, pour 2 kg of special glue for wall covering into 2 kg of water, stir it with a machine, and mix it into the pulp. Keep in mind that the adhesive for wallcovering is thicker and more adhesive than the adhesive for wallpaper, and in order to protect the wallcovering and construction quality, it is best to use a special adhesive for wallcovering with a smooth new perspective. This adhesive is made for the development of wallcovering, which can be applied to 20-30 square meters of wallcovering after adding water to 20 kg of adhesive.

    Apply the wallpaper adhesive to the back of the wallpaper cut with a brush, apply the adhesive to the surrounding edges, ensure the quality of the work, apply the good wallpaper, do not fold the glue for 5-10 minutes. If the glue completely penetrates the bottom of the paper, it can be pasted. Generally, paste the first wallpaper from the edge of the door or the dark corner from top to bottom, gently scrape off the wallpaper from top to bottom, from the inside to the outside, squeeze out the foam and excess adhesive, and lay the wallpaper flat on the wall.

    Cut unnecessary wallpaper at the top and bottom ends to sharpen the blade and avoid hair, and when cutting the wallcovering, it is best to use a Japanese imported blade that sells Korean won on the market. Then use a sponge to dip it in water, you can completely wipe the adhesive residue on the surface of the wallpaper to prevent the wallpaper from turning yellow, and if you find that there is foam on the surface of the wallpaper after drying, you can cut it with a knife, inject the adhesive, and then press it flat to remove it (it is better to use a syringe).

  7. Anonymous users2024-02-07

    First of all, the wall is cleaned first, and then the glue is evenly brushed on the wall, and then the wall cloth can be glued little by little, scraped flat with a small board, and the excess edge is cut off with a utility knife.

  8. Anonymous users2024-02-06

    Be sure to take it slowly, do not appear bubbles during the wallcovering, and pay attention to the distribution of the wallcovering, make a reasonable match, and be perfect.

  9. Anonymous users2024-02-05

    The wall cloth should be deviated from the bottom to the top, first divided into areas, and then pasted one by one, scraping it flat with a hard board.

  10. Anonymous users2024-02-04

    Sticking to the wallcovering should be pasted little by little. Stick it from top to bottom, so that it will be more neatly pasted. In the process of pasting, the air bubbles are directly removed.

  11. Anonymous users2024-02-03

    What are the methods of sticking wall covering, and how to ensure the effect?

    Nowadays, many people choose to apply a wall covering instead of paint when decorating, which is less expensive and easier to create a personalized effect. However, sometimes people have embarrassing scenes when they put on the wallcovering because they have not mastered the technique. So, how to ensure that the wallcovering is bright?

    In fact, you only need to learn the following three methods of wallcovering to present a perfect shape, and you can also solve the problem of bubbles.

    There are actually a lot of tutorials on how to put on wallcovering. Among the various suggestions, the first step is to clean the walls first. Only a clean and flat wall can make the wall cloth appear on the wall.

    One point to note here is that in addition to the dust on the wall, we also need to tidy up the protruding or uneven parts of the wall. You can prepare a small spatula, use the scraper to hang off the excess, and then use a soft towel to wipe the wall first.

    Once the walls are treated, it's time to move on to the next step, which is the process of applying the bottom film. This step is to make us more compliant when pasting later, and we need to brush a layer of bottom film on the wall very evenly. The main point is that it should not be too thick when brushing, otherwise it is difficult to ensure that the entire wall is flat.

    If the first application is not very good, you can apply it a second time. The method of applying wallcovering is not complicated, but steps like a bottom film are a must.

    The last thing to say is a kind of Jingsen answer that often occurs in the method of pasting wall covering, some people will find that the wall is not too flat after pasting the wall covering, and there will be some small bumps and blisters. In this case, a new tool is needed - glue, which actually acts like glue, cut the bubbled area with a small knife, apply glue to it, and then smooth the wallpaper.

    The steps of the method of sticking wall cloth are very simple, and the most important test is people's patience and carefulness. Therefore, in the whole process of pasting wall coverings, don't be too impatient, a little bit, one by one, you can basically achieve satisfactory results, and then you will find that the creation of a beautiful new home is not so difficult.

    You can get it for free

Related questions
15 answers2024-07-25

How to steam fish?

1. A lot of fish can be steamed, but everyone should control the size of the fish when buying fish, and the steamed fish is mostly mastered around 500 grams to 700 grams. >>>More

13 answers2024-07-25

1. Check that the wall surface should be clean and flat before paving, and the surface of the wall skin should not be loose and scattered. >>>More

15 answers2024-07-25

1.Abrasion resistance.

When choosing, you should use a pencil to scratch on the selected wallpaper, and then use an eraser, and those that do not leave traces after erasing are of superior quality, and those that leave traces are defective. >>>More

10 answers2024-07-25

The wallcovering is wallpaper.

Due to the use of silk, wool, hemp and other fiber raw materials, the first grade is much higher than that of wallpaper. >>>More

8 answers2024-07-25

Hello 1Transverse welding is the welding of a weld in the horizontal direction on a vertical or inclined plane. Short-arc welding should be used, and a smaller diameter welding current should be selected, as well as an appropriate transport method. >>>More