What are the methods and detailed steps of wallcovering? What are the steps to clean the wallcoverin

1. Check that the wall surface should be clean and flat before paving, and the surface of the wall skin should not be loose and scattered.

2. Use special tools for pasting wallpaper or other wall cloths, among which it is good to use professional imported wallpaper knives.

3. Dust accumulation on the wall covering. Wipe off the dust directly with a feather duster, dry towel, or vacuum cleaner, and protect furniture and appliances before cleaning.

The walls must be cleaned first, and then the wallpaper will be applied along the wall. When the wallcloth is dirty, you can slightly wet the rag and wipe it clean.

The wall needs to be treated, and it needs to be leveled, so that it can be pasted with wall cloth, and we must pay attention to the flatness, pay attention to the details of the treatment, and generally use a semi-dry wet towel for cleaning.

The wall patching treatment is the application of the wall that has been painted.

Reason: If the wall is painted, because it needs to be treated with cloth. In general, this refers to putting cloth or kraft paper or barbed wire on the wall, except for load-bearing walls.

If you want to stick wall tiles, otherwise there will be a large degree of structural cracks, avoid cracks, enhance the sticking strength and load-bearing capacity of the wall, and the expansion rate of each material is also different.

Therefore, it is necessary to hang barbed wire, and it also needs to be treated with cloth and wallpaper. In addition, it is easy to appear cracks in the wall, and it also needs to be treated, and other walls need to be pasted, if there is no gypsum board partition, it is generally enough to paste cloth or kraft paper.

Precautions: When pasting the mesh cloth for anti-crack on the wall, the pasting method is very particular. Before pasting the cloth, it is necessary to ensure that the wall base treatment is clean, strong, no hollowing, no concave and convex, so as to ensure the smoothness of the cloth.

Roll the wall on the wall, then mix the wall with stucco plaster or putty powder, scrape the mesh cloth on the wall, and flatten it back and forth with a trowel to make the cloth fully bonded to the wall, and cut off the excess part after pasting.

Hello, generally mainly large boards, gypsum boards, interface places. For the smoothness of the whole surface, the final effect is also possible. This is a more responsible master, some directly scrape the ash, the consequences will be cracks. Hope it helps,

That refers to putting a cloth on the wall or putting kraft paper or barbed wire.

Because the wall material is different, the expansion rate of each material is also different, and it is easy to crack the wall, because it needs to be treated with cloth to avoid cracks. In general, except for load-bearing walls, other walls need to be laminated. In addition, the junction between the load-bearing wall and other walls also needs to be pasted, otherwise there will be a large degree of structural cracks.

The wall insulation layer, if not partitioned with gypsum board, also needs to be treated.

If the wall is painted and wallpapered, it is generally enough to apply cloth or kraft paper. And if you want to paste wall tiles. It is necessary to hang barbed wire to enhance the sticking strength and load-bearing capacity of the wall.

1.Check the quality of the wall: Before pasting the wallpaper, be sure to check the condition of the wall, in general, only if the wall meets these three conditions:

When the wall is dry, flat, and the pH is moderate, you can start laying wallpaper. If the wall has been painted or treated with moisture, it should be allowed to dry for 15 working days before starting to be laid.

2.Do a good job of ground protection: Before laying wallpaper, you also need to protect the ground, you know, when laying wallpaper, you need to use glue, so you need to lay a layer of protective film on the ground in advance, such as plastic film, so that when laying wallpaper, the falling glue will not stain the ground.

3.Measure the area of the wall: Paste the wallpaper is not a one-stop paste on the wall, you must measure the size of the wall in advance, so as to know how much wallpaper is needed for paving.

4.Crop the wallpaper: After measuring the area of the wall in advance, you can cut out the corresponding size of the wallpaper.

However, it should be noted that the size of the cropped wallpaper needs to be about 10cm more than the length of the wall, and the extra wallpaper should not be thrown away, it may be used later.

5.There is another problem to note, if there is a beam in the middle of the wall, then when pasting the wallpaper, you should bypass the beam and only paste the part of the wall without a beam, so that the effect will be better.

6.Wallpaper glue softening: In order to make the wallpaper and the wall tightly fit together, the wallpaper needs to be glued. First, use a professional tool to evenly apply the glue to the back of the wallpaper, then fold the wallpaper in half and let it sit for a while (soften).

Steps and methods of wallcovering. Not everyone will need the driver's observation, but also need the hope of learning.

1. Check whether the wall surface is clean and flat before pasting the wall covering, and the surface of the wall skin is not loose and falling off.

2. For special tools for wall covering, it is best to use a professional wall cloth knife.

3. Brush the wall base film on the wall first, and adjust the wall cloth glue in proportion. 2 kg of glue is added in batches. The first time do not add water, stir well.

The second time, start to add kilograms of water, stir well, and then add glue powder and stir well. Add kilograms of water for the third time and stir well. Add the remaining water for the fourth time and stir well.

A bucket of glue can be glued to 25-30 square meters.

4. After the base film is dry, start to roll and brush the wallcloth glue from a certain corner of the wall, generally press the roller brush on a wall, and start to paste the wallcloth after rolling up and down evenly.

5. Straighten the wall cloth along the wall, the upper height is the same as the height of the wall, and the lower end uses an item to pad the whole roll of wall cloth on the upper part of the baseboard.

6. Roll the wall cloth and paste the wall cloth on the wall with a scraper, the order is from the inside to the edge, and then continue to pave the wall cloth in this order after pasting it up and down.

7. If the yin angle is straight, it can be continued without cutting, and the above rolling construction. If the yin corner is not straight, the wall cloth can be lapped and cut at the yin corner.

8. Measure the length from the yin angle to the yin angle, leave a little room to cut the wall cloth, and straighten the two ends from top to bottom, from the inside to the edge.

9. Use a clean, wet towel to wipe off the excess glue around the wall cloth.

10. After pasting the wall cloth for a comprehensive inspection, it is found that there are bubbles and bubbling with a household steam iron.

1. Simple dust cleaning. After the wall covering has been used for a period of time, a large amount of dust will inevitably accumulate on the wall. For general dust, the first thing people do is to use a damp rag to wipe it, but this is actually the wrong way to do it, and it will only make more stains on the surface of the wall covering.

For this reason, the correct thing to do is to use a vacuum cleaner or feather duster to clean the dust off the wall.

2. Oil stain cleaning. Of course, if the wall covering in your home accidentally gets stained with oil or soup, you can use a diluted detergent to clean it, because oil and soup are stubborn stains. If you don't clean it up in time, it will be even more difficult to clean it up in the future.

3. Ordinary stain cleaning. For general stains, one can simply use a slightly damp rag to gently wipe the surface of the wall cloth.

1. First of all, you need to prepare tools to clean and clean the dust on the wall, and make sure that the wall is neat and clean, and there is no falling wall skin and excess dust, so that the wall cloth can be better pasted.

2. Put the glutinous rice glue pasted with the wall cloth in a container for full stirring and complete dilution, and then use a brush to search and evenly apply it on the wall, do not apply it in a large area, only need to apply it in a small area first, and then continue to apply it after the ruler is constantly pasted, so as to prevent the watering time from drying out for too long, resulting in no stickiness.

3. After applying the glue, you can paste the wallcloth on the wall, in the process of pasting, you must be careful, do not let the wallcloth come out of the closed core of wrinkles and bubbles, you should deal with it by hand in time, and finally wipe the wallcloth evenly.

Paste method:

1.All flower products are overlapped and seamstressed, and the flower needs to be started from the middle of the wall to achieve the best flower effect.

2.Brush glue on the wall to avoid glue sticking to the surface of the wall covering. If it spills, wipe it clean with a damp cloth.

3.In order to obtain a good seam effect, the side seam must be pressed with a pressure wheel, otherwise the wall cloth will be easy to show after drying.

4.When pasting, it is necessary to ensure that the surface of the wall cloth is clean, and the hands of the construction personnel should also be kept clean.

5.Do not allow oil to stain the surface of the wall covering.

6.Please close doors and windows during construction and within 2 days after construction. Let the wall cloth dry naturally, and prohibit the use of air conditioners and dryers, otherwise it is easy to warp and crack.

7.When trimming, the utility knife should be kept sharp, and the blade should be kept at a 25-degree angle with the wall, and the force should be even, otherwise it is easy to have burrs.

8.After pasting, wipe off the excess glue with a wet towel and carefully check whether there are bubbles again, if there is a needle to deflate or use a needle to inject glue to scrape flat, and finally use a wall cloth knife to cut the left and right sides.

Precautions in the construction preparation stage:

1.Measure the circumference of the wall from the yin corner to the other yin corner, leave a little leeway, cut the wall cloth, paint the stirred glue on the wall, paint evenly from the middle to the corners, and never paint the glue on the wall cloth.

2.Check whether there is a quality problem with the wall cloth, calculate whether the purchased products are sufficient, and check whether there are still the same batch of products.

3.Check that the wall surface is well treated (dry, flat, hard).

4.Glue: Special glue for strong, environmentally friendly wall cloth must be used.

5.Cutting: The construction cutting environment should be clean, and attention should be paid to the good flowers when cutting the flower wall cloth.

6.The wall covering should not be soaked in water before it is pasted.

Maintenance Phase Considerations:

1.If the edge is hardened and bounced, it can be pressed with water to fill the glue after being wet and soft.

2.If there are bubbles and hollow drums, you can use a wall cloth knife to separate a small opening, release air, inject glue and press the tablet.

3.A little stain can be wiped with a clean sponge live wipe; The dust can be cleaned with a vacuum cleaner and puffed clean with a feather duster; Ink marks can be cleaned with a small mixture of ethanol, water, and detergent; Oil stains can be cleaned with turpentine or mixed with 50% water and water.

The characteristics of the wall covering: the flexibility, non-toxic, tasteless and other characteristics of the wall cloth itself make it favored by the majority of owners. The wall covering not only has the same environmental protection characteristics as the wallpaper, but also is easy to replace, and has stronger sound absorption, sound insulation performance, but also fireproof, mildew and mothproof, and is also very resistant to scrubbing.

Hello! 1. Interface agent: The interface agent must be brushed to the surface, and it must be brushed evenly.

2. Cracks: In general, the cracks are pasted with kraft paper tape and white latex.

3. Leveling: uneven walls need to be leveled, generally gypsum is more commonly used, and the uneven difference does not exceed centimeters.

4. Sticker: Generally, non-load-bearing walls such as light walls and insulation walls need to be pasted, try to choose a better texture wall cloth and white latex, if there are conditions, you can use mesh cloth, the relative anti-crack effect will be better.

5. Putty: It is better to choose putty with high particle fineness and hard texture, and you can also add a certain amount of white latex to the putty, which can improve the hardness of putty.

6. Grinding: try to use finer sandpaper, generally softer putty (such as 821) with 400-500 sandpaper, hard texture (such as wall lining, easy to quack) with 360-400 is better, if the sandpaper is too coarse, it will leave deep sand marks, and the paint can not be covered. After sanding, the wall must be thoroughly cleaned to avoid too much dust and affect the adhesion of the paint.

The difference between bumps and bumps does not exceed 3 mm.

7. Primer: The primer must be brushed evenly to ensure that every place on the wall is brushed, if the wall eats a large amount of paint, it is best to add a little more water to the primer to ensure that it can be painted evenly. Don't think that just because it's a primer, it's okay to use a roller that is a little worse, the effect of the primer will directly affect the effect of the topcoat, and you should use a roller with the same texture as the topcoat.

8. Repair: After the putty is polished, there will be some flaws (pit holes), which are generally difficult to see, only after brushing the paint will be obvious, at this time it is necessary to make up, pay attention to the repair must be polished and smooth, and then brush it with a primer with a little more water, so as not to have color difference when brushing the topcoat because of the different draught with other walls.

9. Paint: Do not add too much water, it will affect the thickness of the paint film, feel and the hardness of the paint film, try to choose a better tool, the hair of the roller is not too short, but it must be fine, so that the paint film will feel delicate, the painting mainly pays attention to the corner, the indirect stubble part of each roll and the direction of the paint, the treatment of the corner, most of the cases is to use a pen or a brush to paint, which will easily cause the texture of the corners to be inconsistent with the whole surface, there will be visual differences, if there are conditions, you can buy a side roller, The corners are painted with a board and then used to close the roller again, pay attention to the material of the edge roller to be consistent with the roller of the large surface, when brushing the large surface, the paint of each roll stubble place must be even, not too thick nor too thin, otherwise it will be inconsistent because of the uneven thickness of the reflection, when the paint is painted every time it rolls on the wall, there will be a painting action, which requires the direction of each roll to be consistent, otherwise it will cause the texture of each roll to roll out is inconsistent, the reflective angle will be different, and there will be a difference in vision. (Suggestion:.)

Buy a tray before painting, it will be sold in the store, and you can use the tray to ensure that every time you paint a roll, the paint on the drum is the same, so that it will be evenly brushed. ）