The uneven ceiling plaster line is bent, how to deal with it?

The uneven ceiling plaster line is bent, how to deal with it? First of all, as the owner of the community, it must be blamed for the poor skills of the workers to escape responsibility, and as a worker, we must evade responsibility layer by layer, the plasterer who installed the plaster strip is uneven, and the plasterer blames the wall for not leveling, but who does the ultimate responsibility is greater This is a fact! The ceiling is not leveled, no matter whose responsibility it is, to install the gypsum line This step is tortuous, it is the obligation of the gypsum line worker, the boss does not blame you for just dealing with it, what should I do?

Why don't Brother Yu give you a few tricks! If the roofs that do not do the ceiling decoration design are scraped flat and neat, if the gypsum line decoration design is definitely much more convenient, but in fact it is not possible! There are certain regulations on the neat level of the wall in the batch putty work, but the level of the ceiling is not so high, which must be repaired with building decoration materials in the middle and later stages.

In that way, when it comes to the step of installing gypsum lines, what should I do if I encounter an untidy ceiling concrete floor slab? Did you see the picture? This is the classic "uneven ceiling disease", after the gypsum line is installed, there is a very large gap between the gypsum line and the ceiling, and there are two solutions to deal with such a thing.

The first is to repair and flatten the ceiling and then install plaster lines. However, it is not easy for the master who installs the gypsum line in such a restoration work, even if the labor cost is increased! The second is to see a similar situation after the installation of the plaster line, you can fill the gap with putty powder, so that you only need to ensure that the tone is the same as the ceiling decoration design, and there is not much gap in the actual effect level!

This is also the most common way for gypsum line installers, and it is also the most unwilling situation! The situation of the crooked plaster lines is not assembled by the above two methods, but is to evade responsibility and put it in the shape of smallpox.

The plaster line must be curved to assemble the appearance of the ceiling, and the first is to disassemble the revision, and the second is to choose not to care about this kind of practical effect, but even if it is clearly proposed how to deal with it, there is no doubt that it is unacceptable! If you can't accept it, disassemble and redo it, assemble it according to the specific situation of the second point above, and the actual operation process is as follows:1

Construction pay-off: Arrange a straight line on the wall according to the size and model of the gypsum line, and take the highest place as the specification! Assemble:

When assembling, the bottom edge of the plaster line is about the same as the straight line placed on the wall, and the gap between it and the ceiling is as much as it is.

Repair: There is no doubt that there is a gap between the plaster line and the ceiling when it is assembled horizontally, and the gap should be repaired at this time to improve the overall practical effect of the plaster line! At the same time, the sockets at the corners of the plaster lines were repaired.

Brushing: After the gypsum line is installed, it is necessary to carry out the coloring solution according to the regulations, according to the color of the wall or according to the matching color, pay attention to observe whether the parts that must be repaired are cracked, and deal with it as soon as possible!

First you have to fill the gaps with plaster, then you have to adjust the uneven areas, and then you have to trim them with color.

The gypsum line can be installed after the ceiling is repaired and leveled, but this will increase the cost of the project, and the gap can be filled with gypsum powder after the gypsum line is installed, which is the most commonly used method of the gypsum line installer, and this method is relatively simple and fast.

It may be that your wall is uneven, and you can fill it with some boards, so that the plaster line can be made flat.

How to change the gypsum line pattern if it is not good-looking! Hello, I am glad to answer for you<> 1, to remove the loose gypsum line first, you can use a knife to cut off both sides of the broken gypsum line, so that the gap becomes larger, and the edge line becomes clearer, and then take away the bad plaster, with a vacuum cleaner and a brush will clean the surroundings. 2. Add water to the gypsum to be used to adjust it, and then use a paint brush to brush the gap with water, so that the gap is all wet, fill the gypsum in the crack, and dry it for more than 24 hours.

3. If you find that the damage is only a partial location, you can wait for the plaster to dry, wrap it in sandpaper outside the plaster, and gently polish the repaired place. If the damage is large, the plaster should be applied again until the surface becomes smooth, and it should be noted that in order to ensure the effect of plaster repair, it must be wet with water before applying the plaster each time before continuing to apply it a second time. If the pattern is not obvious, the pattern is simple, such as the lines are similar, it is easy to repair, and you can draw it once with the color you like.

The pattern is complex, it's that easy, it's not that it's hard to repair, but it's time-consuming and laborious! Spending money on labor costs, it is better to replace the original gypsum line with the pattern you like. Hope mine can help you <>

Do you have any other questions?

If the ceiling is uneven and the plaster line is made according to the ceiling, it must be bent! What does this prove? First of all, as the owner, it must be blamed for the bad technology of the workers, and as the workers, we must shirk the responsibility layer by layer, the plasterer who installs the gypsum line is not smooth, and the plasterer blames the unevenness of the wall, but who does the final responsibility is greater This is a fact!

It doesn't matter whose responsibility it is for the unevenness of the ceiling, when it comes to the step of installing the gypsum line, it is the responsibility of the gypsum line worker, and the boss does not blame you for just handling it well, what should I do? Let's give you a few tricks!

If the ceiling of every house is not decorated with suspended ceilings is scraped flat and neat, it must be much more convenient to do gypsum line decoration, but in fact it is not possible! The plastering work has certain requirements for the flatness of the wall, but the requirements for the flatness of the ceiling are not so high, which needs to be repaired with decorative materials in the later stage.

So, when it comes to the step of installing the gypsum line, what should I do if I encounter an uneven ceiling floor?

See the picture above? This is the typical "smallpox symptom", there is a large gap between the plaster line and the ceiling after installation, and there are two solutions to this situation.

First, the ceiling can be repaired and leveled and then installed with plaster lines. But the master who installed the gypsum line would not be willing to do such a repair work, even if the price was raised!

The second is that after installing the plaster line, you can fill the gap with gypsum powder, so that as long as it is the same color as the ceiling decoration, the effect is not much different! This is also the most common method used by gypsum line installers, and it is also the most unwilling situation!

In the case of bending and twisting the gypsum line, it is not installed in the above two ways, but irresponsibly installed in the appearance of ceiling.

The gypsum line must be bent to install the appearance of the ceiling, and the first is to dismantle and redo it, and the second can only choose not to care about this effect, but since it is proposed how to deal with it, it must be unacceptable!

If you can't accept it, disassemble and redo it, install it according to the situation of the second point above, and the specific operation steps are as follows:

1.Pay-off:Place the horizontal line on the wall according to the size and specifications of the plaster line, and use the highest point as the standard!

2.Installation:When installing, the bottom of the plaster line is level with the horizontal line placed on the wall, and the gap between it and the ceiling is as large as possible.

3.Patching:There must be a gap between the plaster line and the ceiling when it is installed horizontally, and the gap needs to be repaired at this time to enhance the overall effect of the gypsum line!

At the same time, the interface at the corner of the gypsum line is repaired.

4.Brushing:After the gypsum line is installed, it is necessary to carry out coloring treatment according to the regulations, according to the color of the wall or according to the matching color, pay attention to observe whether there are cracks in the parts that need to be repaired, and find it in time and deal with it as soon as possible!

When the plaster line encounters uneven ceilings, it is the above treatment methods, do you have any objections to this? Thanks for sharing your tips!

It is found that there is a similar situation after the installation of the plaster line, you can fill the gap with gypsum powder, so that as long as the color is consistent with the ceiling decoration, the effect is not much different!

The uneven ceiling is re-treated. Finally, you can repaint the color of the ceiling plaster line again so that it has no color difference.

You can use quick-adhesive powder to paste it in the corners of the wall or in the joints, without leaving gaps. First get the roof, then the walls, and finally the floor.

Here's what we have to say.

1.When pasting the gypsum line, remember to supervise the master, they generally do not notice these problems in order to find money: the surface of the plaster line should not have too much dust, so the material is also a special gypsum, on-site deployment, in this construction process, the most important thing is to paste a section of the best, the gypsum line and the wall contact.

The surface treatment is smooth, the uneven places must be scraped clean, and the protruding places must be dealt with, otherwise the work behind is not only not easy to do, but may also damage the gypsum line and affect the appearance. If there is a seam in the corner of the plaster, it should also be used.

Gypsum caulking treatment.

2.The master of scraping putty must deal with the edge of the gypsum line, as long as this job is done in the first step, it is relatively simple, because the gypsum line is straight. By the way, the gypsum corner seam will also be wiped to facilitate the later polishing.

The above is the gypsum line seam treatment process.

One is that the production is that the glass filament is not put well.

The second is that after being cooled and dried, it is damp again.

The third is that I have been leaning there for a long time.

Home Bright Gypsum Line Mold.