Do you want to scrape putty behind the wardrobe? What does it depend on?

Do you want to scrape putty behind the wardrobe? What does it depend on? Whether you need to batch putty at the back of the wardrobe depends on the situation.

If you choose a wardrobe customization, the conventional operation behind the wall will do a good job of moisture-proof treatment, so you don't have to batch putty, if you choose a finished wardrobe, you must batch putty behind the wardrobe. When choosing a wardrobe customization, because the wall has already done a good job of the main moisture-proof treatment, if there are some gaps in the middle and late stages, it is not recommended to batch putty, because the putty powder is hard after the material is extinguished, it may lead to the corresponding deformation of the box, and the putty powder may fall down first, not to ensure that the gap is made up in detail, you can play porcelain white glue to make up for the gap.

When selecting the finished wardrobe, you must first batch putty, which can adjust the unevenness of the cement wall itself, because the wooden cabinet is all horizontal, so when catering to the wall, a little bit of unevenness is so easy to be seen, the batch of putty can make up for the gap, so that the closure is more beautiful and generous. In the end, to sum up, whether the back of the wardrobe needs to be batch putty depends on the situation, and if you choose a wardrobe to be customized, you don't need to batch putty, and if you choose a finished wardrobe, you must scrape the putty powder in advance.

To put it simply, it is necessary to batch putty first, and then make wooden cabinets, to ensure that the wall on which the box is based has a good flatness and fit, so that the cabinet is installed more firmly, and some homes consider that the back is not moved, not disassembled, and there is no need to do it, and I personally feel that there is no need to save this large amount of money. For wet and cold areas, or the back wall of the box and the bathroom use the same wall, we must pay attention to the waterproof and moisture-proof solution, otherwise once the deformation is cracked, the decoration cost of tens of thousands of yuan will be wasted, if the master is serious enough, it will also paste a layer of tin foil on the reverse side to block moisture.

Now it is a kind of selection to the most wooden cabinets, after confirming the specifications and plates, etc., produced by the manufacturer, immediately assembled on the spot, the side panels are immediately leaned against the wall, so it is stipulated that the putty is scraped to do a good job of closed solution, and it can not be assembled immediately without scraping, otherwise it is very easy to fall off the powder in the middle and late stages, resulting in difficult removal. In addition, there is a certain gap between the side panel of the wooden cabinet and the wall, which must be solved by sealant, and these parts must be scraped with putty powder first, otherwise it will seriously endanger the beauty and generosity of the gap.

If you choose a custom wardrobe, the regular operation behind the wall will be done to prevent moisture, so don't scrape putty, if you choose a finished wardrobe, you need to scrape putty behind the wardrobe.

When choosing a custom wardrobe, because the back wall has been done with basic moisture-proof treatment, if there are some gaps in the later stage, it is not recommended to scrape the putty, because the texture of the putty is hard after drying, which may cause the relative deformation of the cabinet, and the putty may fall off first, and it is not guaranteed that the gap is filled completely, and you can play porcelain white glue to fill the gap.

The first is whether the wardrobe is fixed or removable, if it is a fixed wardrobe, it can not be scraped, because it will not affect the appearance at all, if it is a mobile wardrobe, it needs to be scraped, because the wardrobe will be removed one day. The second is to see whether their decoration funds are sufficient, if they are sufficient, they can choose to scrape putty, so as to facilitate subsequent use, if they are not sufficient, they can choose not to scrape, saving an expense.

Want. Since this one location is not done interior decoration is particularly ugly. The second situation is that everyone's home is a custom-made cabinet.

In other words, we use the method of customizing furniture in the whole house when decorating our homes, some of these cabinets are placed in the wall, and some are immediately made on the wall.

Door-to-door installation of furniture cabinets, after the overall interior decoration is completed. When decorating the wall, it is impossible to follow the area of the cabinet, and the wall behind the cabinet will not scrape putty.

Finish. I have never heard of such a decoration, decorate the wall according to the order of the process, and install the common cabinets at home are the finished cabinets. The so-called finished cabinet here is the cabinet we buy directly from the furniture store, and then put it directly where we need to place the cabinet.

<> according to the situation, it is still necessary to do a certain treatment, such as the wall near the bathroom to make a wardrobe, it needs to be waterproofed, so as not to affect the service life of the wardrobe due to water seepage in the future. Other dry places should come how to come, scrape putty or not, there is nothing to start the first leveling, everything that can be seen from the outside, except for the part in the middle of the door, everything else must be scraped into white or gray. Basically, after the completion of the carpentry ceiling, it can be seen outside the indoor kitchen and bathroom.

Now we will communicate with customers about the location of the cabinet that needs to be installed, close to the bathroom and kitchen wall, we will first brush the waterproof 2-3 times, and then use water-resistant putty powder.

Batch twice, no polishing or painting. It can effectively prevent water seepage, and can adsorb a certain amount of moisture, other special materials, of course, there is no need to scrape any putty, if the wood appliance material is scraped with putty, and the surface is sprayed with glossy paint, it will be a good protection of its service life, and now most of the wood appliances on the market are scraped putty and processed perfectly.

If the partition wall of the cabinet is a bathroom, the designer will also ask the owner whether the wall on this side of the cabinet needs to be brushed with waterproof paint on the premise that the bathroom is waterproof.

Prevent the wall from being damp and affect the life of the cabinet. When decorating, as long as we make cabinets on site, the back is generally not painted, and there is no problem. But it's okay to do it the other way around.

Tiles are generally pasted in common areas such as living rooms, balconies, kitchens, and bathrooms. The tiles are directly plastered on the wall, and there is no need to apply putty powder.

Need. Scraping putty is for aesthetics, but also waterproof, the back of the cabinet needs to be scraped putty, because sometimes you will change the decoration of the home, you will move the cabinet, if you say not scrape, it will look unsightly.

Putty is needed behind the cabinet, because scraping putty is a decoration, and it is not easy to carry out a decoration. The cabinet is often moved, and if the putty is not scraped behind the cabinet, it will have to be renovated at that time.

I think it is still necessary to scrape putty, because in this way to ensure the beauty of the interior, and the putty can also effectively prevent moisture and insects, so I think such a step is very necessary.

The fixed cabinet does not need to scrape putty, because the cabinet panel can be directly fixed on the wall, and the wall behind it cannot be seen, and there is no need to scrape putty for beautification.

In response to the question of "scraping putty first or installing the wardrobe first, how would you choose?" "This question, in my personal opinion, should be based on the actual situation:

First of all, if the house is still a rough house, then you have to scrape the putty first, and then install the wardrobe, think about it, if the house is a rough house, then the walls are rough, so that the sand will fall, so that if the wardrobe is installed, it is more troublesome to clean the room in the future, and some sand will often fall in the room, which is not conducive to the cleaning of the room, if you scrape the putty, the wall will be much smoother, and these situations will not occur, so if it is the case of the blank house, you must first scrape the putty and then install the wardrobe, This makes it much easier to clean up in the future.

Secondly, if the house is a semi-finished house, that is, the decoration is halfway, if the wall has been treated, not rough, you can directly install the wardrobe, and then scrape the putty after installing the wardrobe, so that the wardrobe can be well connected with the wall, and there will be no more flash gaps, so that the back of the wardrobe will not enter the dust, nor will there be spider webs, nor insects, otherwise the wardrobe and the wall can not be well joined together, flashing a large gap, there will be dust, and it will become a place for mosquitoes to hide, for a long time, It will be full of dust, and it is not easy to clean, and it will also hide a lot of small insects, so the best way is to install the wardrobe first, and then scrape the putty, so that the gap between the wardrobe and the wall can be sealed, and there will be no dust and no small insects.

Third, if the wall is too wet, it should be cooled and dried, and then the wardrobe should be installed, you must know that the wardrobe is wood, if it touches the wet wall, it will be deformed, so it is necessary to cool and dry it before installing the wardrobe, so that you can avoid the phenomenon of wardrobe deformation, if the conditions permit, you can do waterproofing on the wall that is ready to install the wardrobe before installing it, so that the wall will not get wet, otherwise it will reduce the service life of the wardrobe.

These two processes belong to two different types of work, one is wall decoration and the other is furniture building, and the order should have no influence on each other? However, both types of work are on-site construction, and it is certainly inconvenient to carry out them at the same time, so it is divided into a sequence! Is the decoration to scrape putty first or make cabinets first?

Many people have been very entangled in this issue, after all, laymen do not understand the decoration procedure, and it is normal to not know whether to scrape putty first or make cabinets first. Usually, putty should be scraped first. Generally, after pasting the bricks, the carpentry began to carpentry, the task of carpentry is to suspend the ceiling, hit the cabinet, because the cabinet is made of carpentry, some details are not easy to deal with, such as the wall is uneven, or the wall is tilted, and the carpenter can not do the oblique when making the cabinet.

The general practice is that the water goes to the top and the electricity goes to the ground. There are also hydropower that go to the top or go to the ground. After the water pipe is ready, not only the pressure test should be carried out, but also the water discharge test should be carried out.

The wire requires that all dark wires must be threaded through the conduit, and each wire head can be twitched. Painters cause a lot of inconvenience, must do a good job of finished product protection, all cabinets with protective film to protect up, although whether the first cabinet or putty will be the finished product protection of the cabinet, but the first cabinet to be installed, it will definitely increase the difficulty of finished product protection. The wardrobe is mostly made of solid wood boards, solid wood boards are most afraid of moisture, scrape 1 or 2 times putty behind the cabinet, preferably water-resistant putty, which can play a part of the moisture-proof role, and has some blocking effect on the dampness in the wall to penetrate outward.

Avoid gaps between the cabinet and the top surface of the wall, which will affect the appearance. Usually carpenters do a good job of the cabinet, horizontal and vertical, when the oiler is leveling the top surface of the wall, he will fill the gap between the cabinet and the top surface of the wall with plaster, and at the same time level the top surface of the wall to ensure that the cabinet and the wall are tightly fitted.

In this way, you can do a ground self-leveling, otherwise it is not necessary to find a vertical angle, and it is also a waste of money, and the effect will not be obvious. Of course, the main function of self-leveling is to make the indoor ground level better, which can make the effect of laying the floor better in the future.

Personally, I think it is necessary to scrape the putty first, because in the process of scraping the putty, it will inevitably exceed some ranges, if you install the wardrobe first, and then scrape the putty, it will stain the wardrobe, and it is difficult to clean off, and some of the traces left by the putty will be scraped.

I chose to scrape putty first and install the wardrobe. In this case, even if I think this wardrobe is not good-looking, it will be easy for me to change it at that time, but if I install the wardrobe first and then scrape putty, I think it will be difficult.

I will choose to install the wardrobe first and then scrape the putty, so that the damage is relatively small. There will be no secondary damage, and the integrity of the house will be relatively high.

Of course, I install the wardrobe first, and then scrape the putty, after all, it takes time for the putty to dry on the wall.

Generally, carpentry is done first, and then the wall is made, if the wall is done first, the carpentry is done and the wall is broken.

It should be necessary to brush putty. Although the back of the wardrobe may not be seen often, but if you want to change the style of the whole home, and then move the wardrobe away, you will find that the back of the wardrobe is really a mess.

I think the two types of work can be cross-worked, you can first scrape 1 or 2 times of putty, and then carry out the on-site production of the cabinet, and then complete the last putty construction after the cabinet is done! This operation can well deal with the gap between the cabinet against the wall (except for movable cabinets or customized cabinets), and achieve the dense effect of mixing the cabinet and the wall.

If the wall surface is in good condition, the on-site carpentry cabinet is made on the floor tiles.

Once you're done, you can make the installation. The same is true for factory-customized wardrobes, which can be scraped without waiting for putty.

You can install it. The disadvantage is that after the wardrobe is installed, the painter will cause a lot of inconvenience to the painter again, and the finished product must be protected, and all the cabinets will be protected with a protective film. According to the normal procedure, the ground decoration (bricklayer paving) is completed to the carpenter, the ceiling decoration and the cabinet building are completed at this time, and then the painter enters the site to complete the putty scraping or some other materials of the wall decoration.

The general practice is that the water goes to the top and the electricity goes to the ground. There are also hydropower that go to the top or go to the ground. After the water pipe is ready, not only the pressure test should be carried out, but also the water discharge test should be carried out.

The wire requires that all dark wires must be threaded through the conduit, and each wire head can be twitched. Of course, if the floor decoration is made of wooden flooring, it can also be arranged after the cabinet is built, so that the occupied position of the cabinet does not need to be decorated, which has the advantage of reducing the cost of floor decoration!

When the new house is renovated, the construction is carried out in accordance with the order of the process, first of all, the indoor water and electricity are changed, the water and electricity installed by the developer are only the approximate location, the water and electricity are reinstalled according to the height specified by the owner, the water and electricity are changed, and the bathroom is waterproof paint three times.

Confirm that the waterproof paint is dry thoroughly, and then paste the wall tiles and floor tiles, wall tiles, and floor tiles after pasting.