How to make styrofoam, how to make your own styrofoam

1.Pour less than half a cup of glue into the cup and add a small amount of pure glycerin, and squeeze into the shower gel, which can add a super drawing effect to the styrofoam.

2.Using chopsticks, stir the glue, glycerin, and body wash in the cup until well combined.

3.Add soda water and stir to mold, after molding, test the extensibility of the bubble glue by hand, and the foaming glue is completed.

How to make styrofoam:

1) Start by taking a clean container with a lid (disposable boxes are recommended); Squeeze some of the dish soap into the container.

2) Squeeze some more toothpaste into it and add a little water.

3) Close the lid of the container and shake vigorously until it bubbles.

4) Add a small half box of glue and squeeze in some hand cream and mix well with a spoon.

5) Finally, add the laundry detergent and mix well with a spoon until the styrofoam is formed. In this way, the homemade styrofoam is ready, soft and smooth, and it can also make a crackling sound.

The production of styrofoam is very simple, and there are two different methods described below: Method 1: Use glue and laundry detergent as the material. The glue can be chosen arbitrarily, and the laundry detergent should be used by the skin and the baby as much as possible, such as Blue Moon, Tide, Blue Wave, etc

Use clay, hot water, dish soap and soapy water. There are no special requirements for the material part, and the commonly used ones at home can be used.

Materials required: appropriate amount of toothpaste, appropriate amount of facial cleanser, appropriate amount of water, appropriate amount of glue.

1. Squeeze an appropriate amount of toothpaste into a small bowl.

2. Add water and stir.

3. Pour into a box with a lid.

4. Put in an appropriate amount of facial cleanser.

5. Shake the box.

6. Pour back into a small bowl after foaming.

7. Add glue and stir well.

8. Turn it into a solid form.

Pay attention to styrofoam:

1. To avoid the styrofoam molding is not soft enough, you can add an appropriate amount of glycerin and other soft things to stir.

2. It is best to add warm water when stirring, which can ensure its flexibility and better drawing.

3. If you do a good job of styrofoam for a period of time, you will lose most of the water because of contact with the air, and you only need to rub it with warm water or glycerin at home again to get a new styrofoam.

4. If there is too much glue and the foaming glue is particularly sticky, you can wait for it to evaporate for a while.

Add glue first, then add a small amount of toothpaste and stir from white, then add your favorite color paste, then add an appropriate amount of borax water, stir to form, and then start to foam. Simple styrofoam ready. The specific steps are as follows:

Materials: glue, toothpaste, pigment, borax water.

1. Prepare a container and add an appropriate amount of glue.

2. Add a small amount of toothpaste and stir well.

3. Add a few drops of pigment of your favorite color and stir well.

4. Stir well, then add an appropriate amount of borax water, and stir to form.

5. Then start bubbling, lift it up when it's bubbling, then fold, fold again, fold again, repeat a few times.

Precautions: 1. Do not let the glue stick during the production process.

2. Be careful not to play with children to prevent accidental ingestion.

Preparation materials: water, glue, glycerin, makeup remover, fairy water Appropriate amount of production method: 1, press 1:

1 ratio ready with water and glue. 2. Pour the two materials into the container. 3. Add an appropriate amount of cleansing water.

4. Stir them well with a spoon. 5. Add glycerin to prevent the styrofoam from becoming brittle. 6. Add a small amount of fairy water several times until the solution forms a clump.

7. Stretch your hands after taking out the lump of solution. 8. Keep overlapping and kneading until it is completely lumped. 9. Finally, it is not sticky, and the styrofoam is completed.

Prepare materials: water, glue, glycerin, makeup remover, fairy water to taste.

Production method: 1. Prepare water and glue according to the ratio of 1:1.

2. Pour the two materials into the container.

3. Add an appropriate amount of cleansing water.

4. Stir them well with a spoon.

5. Add and add glycerin to prevent the styrofoam from becoming brittle.

6. Add a small amount of fairy water several times until the solution forms a clump.

7. Stretch your hands after taking out the lump of solution.

8. Keep overlapping and rubbing until the group is completely successful or broken.

9. Finally, it is not sticky, and the styrofoam is completed.

Styrofoam is a very interesting thing, especially for many children, they are very happy to dress up and sell fun, and the production method of styrofoam is also very simple, now I will teach you how to make styrofoam. The specific steps are as follows:

Step 1:

First of all, prepare the following materials: transparent glue, glycerin, washing and washing liquid, and molding water.

Step 2:

Pour a small amount of laundry detergent (shampoo or shower gel can be substituted if you don't have one) into a clean container, and then pour in another 100 or 200 ml of liquid glue.

Step 3:

After that, pour an appropriate amount of glycerin into it, and if there is no condition, you can use water instead of glycerin.

Step 4:

In the process of adding materials, we must keep stirring, how to make the raw materials mix together.

The first hall teases six steps:

Finally, we add a large amount of foam and stir well, adding a small amount of molding water but several times until it is formed.

Therefore, as long as you follow the above methods and steps, you will be able to easily make fun styrofoam.

1. Shower gel to make styrofoam, shower gel is available in every home, we can use shower gel to make styrofoam, first prepare an easy, slag bird pour a small amount of transparent glue, and pour in transparent shower gel, stir well, then add some molding water, stir until the molding is round, let it stand for about a week during menstruation, and the styrofoam will be ready. 2. Toothpaste to make styrofoam, toothpaste can also be used to make styrofoam, first prepare a container, add an appropriate amount of glue, and add a small amount of toothpaste to stir evenly, then add a small amount of pigment to stir evenly in the cavity, and finally add an appropriate amount of borax water to stir and form, and after it is foamed, it can be completed by repeatedly lifting and folding it three times.