Gypsum board wall, tell me how to deal with it?

Gypsum board ceiling, in fact, is basically the same as the façade wall to make gypsum board partitions.

After the plasterboard is ready, the treatment process of the wall can be carried out according to the following steps.

1. Plate seam treatment.

The gypsum board and the gypsum board are spliced together, and there must be seams in large or small sizes. Such seams, if not treated well, can cause cracking in a very short period of time.

At the moment, no one can make these seams 100% never crack.

However, there is an international practice that can delay the cracking of the joints, of course, it is not 100% never cracking, but it is recognized as effective.

2. Scrape putty.

It is better to scrape the putty first and not omit this step.

Gypsum board, generally paper-faced gypsum board, the outermost layer is paper, which is also the most vulnerable place of paper-faced gypsum board. Generally, there is a problem with the paper surface of the **, and there will definitely be problems such as cracking from here in the future.

The moisture content of latex paint is very high, and the paper surface of gypsum board is directly soaked with so much water once, it is difficult to guarantee that there will be no problems, and it is much better if there is a putty layer to do a buffer.

In addition, after the seam treatment, scraping putty can make the base layer flatter and more uniform. If you do not scrape putty, there may be a certain color difference between the place where the caulking is done and the color of the paper.

3. Paint. There's not much to talk about about this. Looking at the first floor, the introduction is very clear.

Again, the partition made of gypsum board has basically the same treatment process!

Before making the keel, it is best to take a concrete or brick 20 cm platform and then make a light steel keel gypsum board wall.

The seams should be taped with bandages or cloths, scraped with putty, and painted.

1. Plate seam treatment, 2. Scraping putty, 3. Painting.

No. drywall.

It can be attached to the wall, but it basically cannot be the basis of the painting, a blank wall, or a brick wall. Combine gypsum veneer walls, because the walls are flat and have specific requirements. The walls are spread with adhesive plaster, and the plaster stone is pasted.

Because the gypsum core itself is non-combustible, and when exposed to fire, it will absorb a large amount of heat in the process of releasing the combined water, delaying the rise of the surrounding ambient temperature. Therefore, gypsum board has good fire and flame retardant properties.

Can plasterboard be placed on the wall? Yes, the process flow: and the elastic line grade:

The elastic line is made of the width of the keys at the junction of the upper, lower, and both sides of the foundation and partition wall. The bullet line is clear and the position is accurate. According to the design requirements, the length and width of the cover panel are combined to determine the vertical panel.

The position of the cross lattice and the additional keys.

Make pillow straps: If you need to design, make pillow straps according to the design requirements. The pillow harness must be closed, and a role must be assigned to close the Piso light concrete.

Can plasterboard be placed on the wall? Fix along the project buttons; Nails or extension bolts can be fixed along the keys along the bullet line position fixed to the project, and the spacing of the fixing points must be less than 600mm. Fixed bar key:

Fix the border line along the bullet line, and the edge of the keyboard is consistent with the bullet line. The key ends should be fixed, and the fixed point spacing should be greater than. How is drywall set up?

Gypscale is a decorative board commonly used on the ceiling of modern home decoration.

Can plasterboard be placed on the wall? In the installation process of gypsum board, a certain degree of method and attention is required to ensure the installation effect. How is drywall set up? What do I need to pay attention to when installing?

Gypsum board installation methods and precautions for the use of the environment, conditions, according to the correct choice of gypsum board type.

1.Waterproof gypsum board should be selected in a room that is prone to moisture, such as a kitchen or bathroom, or should be used after a moisture-resistant treatment on the surface of general gypsum board to ensure that it has some waterproof properties in future use.

2.The construction of the upper layer of plasterboard should be carried out after the walls have been painted. If the partition wall adopts gypsumboard lightweight steel key wall, and the partition wall reaches the bottom of the floor, the setting of the ceiling is carried out after the partition wall.

When the partition key reaches the ceiling height, the ceiling must be set first. The construction of the interior site must be completed before the ceiling can be installed.

Can plasterboard be placed on the wall? The setting of the drywall, 1) Direct paste setting: The roof is smooth and flat, if you want to cut the drywall too long, you must start from the front first, and then cut the paper on the back, so that you can cut off the edge all the way.

2) Set the horizontal screws. When using a wooden keyboard, fix the round nails and screws and apply them with mud

You can get it for free

Gypsum board background wall is one of the common decorative materials in modern home, which is more and more popular because of its simplicity, beauty, and easy construction. However, there are many things that need to be paid attention to in the construction process of gypsum board background wall, and the following family will introduce in detail the method of gypsum board background wall treatment.

1.Adjust the flatness of the wall.

Before the wall treatment of the plasterboard background wall, it is necessary to check the flatness of the wall surface. If there are problems such as unevenness or obvious bulging and cracks on the wall, it needs to be treated first. This can be done by applying putty, sanding or digging out parts of the wall.

2.Install soundproofing cotton.

Before the installation of gypsum board, you can install soundproof cotton board on the wall to achieve sound insulation effect, especially suitable for living room, bedroom and other rooms that need to maintain a high-quality living environment, and the overall effect of installing soundproof cotton is better.

3.Drywall size standardization.

Before the construction of the gypsum board background wall, it is necessary to measure the size of the wall and customize the gypsum board that meets the size of the wall. In order to improve the effect, you can apply the wiring film on the back of the gypsum board, so that the size of the gypsum board is relatively more standardized, so that the decorative effect of the whole wall is more perfect.

4.Gypsum board wall construction.

The construction process of gypsum board wall is relatively simple, and only the skeleton process is required, and the size of the board is cut first, and then installed on the wall skeleton. After installation, it is necessary to use a special gypsum board background wall joint agent for joint treatment to achieve the effect of neat and tidy wall and beautiful appearance.

5.Latex paint treatment for walls.

After the wall construction is completed, the wall needs to be treated with latex paint. Depending on your personal preference, you can choose a softer or brighter color to give people a different visual experience. The latex paint can also be coated with a transparent protective film, which can better care for the wall and prevent friction and scratches.

The above are the general steps of gypsum board background wall wall treatment, do these jobs well can make the gypsum board background wall decoration effect better, and make your home decoration more beautiful.

Some families install gypsumboard at home when decorating, but many people don't know how to deal with this material when pasting wallpaper, so, in order to satisfy everyone's curiosity, be prepared when pasting wallpaper, take a lookHow to deal with gypsum board wallpaper wallpaperThere are several main methods: keeping the wall flat, scraping putty, scribing, and the wall temperature is moderate.

If the walls of the old house have peeling, cracks or projections, a wire brush or a piece is basically the level of the first wall, clean the wall, the concrete wall as much as possible so that no surface dust is exported. The primer must be cleaned to remove the walls. If the old wallpaper is replaced, the residual glue will remain after the old wallpaper is torn.

The glue should be removed and then cleaned. Theoretically, the standard for wall leveling error is about 3 mm.

Make sure that after the formation of the solid wall, the rollers of the concrete wall of the surfactant are as uniform as possible, and the smug is allowed to dry, and the tank is bent in the field. Putty is a kind of flat decorative wall material, and the main treatment before putty is the most important wallpaper step. As a rule, putty is scraped on the side, which removes the base layer by filling the uneven surface part, making the wall smooth.

The best way to putty is water-resistant putty, putty this construction and polishing is relatively less difficult, but to do putty feels good, waterproof, breathable, has high adhesion, durability, in the need to eliminate 1-2 days of zero putty in the need to redecorate, brush and polish on the wall to avoid too long time, because too hard putty, increase the difficulty of construction.

After the putty is dried, the primer is repaired, and if it is a new house, you can choose to brush the white primer. In addition to the repair function when starting, the most important thing is to form on the surface of the wall of the protective film, the wallpaper can effectively prevent corrosion.

First of all, the water absorption of the wall surface in the water on the wall surface can be tested. If the water is quickly inhaled, roll the wall again with water and make sure the wall surface is hydrated. As a rule, after 1-2 days of primer application, vertical lines can be drawn after the primer has been primed.

Use a calibration hammer to measure the vertical reference line, starting at the corner of the wall and drawing along the vertical reference line on the wall.

These are:How to deal with the wall of gypsum board paste wallpaperThere are a few ways to keep in mind.

You can get it for free

Gypsum is a common material, which can be widely used in the decoration and decoration process of home building materials, such as some decorative gypsum boards, which can be fixed on the wall, which can make the overall structure more beautiful, and gypsum is also easier to shape in the later stage, and can be made into a variety of shapes according to our needs. Today's recommended example for you is about the method of plaster fixing on the wall and the process and steps of the description information, interested friends can synthesize this step to start, hands-on operation, I believe you can achieve satisfactory results.

1. How to fix gypsumboard to the wall

There can be 2 kinds: one is the bonded gypsum veneer wall, which has certain requirements for the flatness of the wall, and the bonded gypsum is dotted on the wall, and then the gypsum board is pasted. The second is:

Light steel keel veneer wall, this is a bit complicated to do, if you are interested in this method, I can mess around with the node diagram made for you, you can refer to the drawings to make it.

Second, gypsum board installation method

1) Construction process.

Elastic roof elevation line Draw keel binning line Install pipeline facilities Install main keel boom Install main keel Install secondary keel Install paper gypsum board Brush anti-rust paint Install strip Gypsum line installation.

2) Bullet roof elevation level line.

According to the floor elevation level, use the ruler to measure the vertical vector to the ceiling design elevation, and pop the ceiling elevation level line along the wall and column.

3) Draw the keel binning line.

According to the design requirements of the main and secondary keel spacing, on the elevated line of the roof has been bounced on the keel binning line.

4) Install the main keel boom.

After playing the elevation level line of the ceiling and the keel binning position line, determine the elevation of the lower end of the boom, according to the position of the main keel and the hanging spacing, one end of the boom without bolt thread buckle and the embedded reinforcement of the floor slab (expansion bolts can be used when the embedded steel bar is not embedded) are fixed by welding, and the welding part is coated with anti-rust paint.

5) Install the light steel keel main keel.

1. Equipped with boom nut.

2. Install the hanging parts on the main keel.

3. The main keel of the assembled hanger is inserted into the corresponding boom bending bolt according to the position of the gear line, and the nut is screwed.

4. Install the connector at the junction of the main keel, and adjust the elevation, arching and straightening of the cable.

5. Install the main keel attached to the hole, and set the connection card firmware according to the corresponding node structure of the atlas.

6. Nail the edge keel and fix it with nails. When the design is not required, the nail spacing is 1000.

In addition, there are instructions and precautions about the process steps, which can be known that generally speaking, if you want to fix gypsum board of various shapes and sizes on the wall, and want to make the overall structure more beautiful and visually more satisfactory, you should pay attention to more places, including whether the gypsum board can not fall as easily as expected. As well as some fixed spare parts, you can find the answer from the above.

You can get it for free

Wall decoration gypsum board is a very popular decoration method, which can not only beautify the indoor environment, but also play a role in sound insulation, heat insulation and so on. However, decorating gypscale also requires some skills and precautions, and the following will introduce the steps and precautions for decorating wall gypsum board.

Step 1: Preparation.

Before construction, it is necessary to do a good job of accurate ruler preparation. The first is to buy gypsum board, to choose the best quality, smooth appearance, no flaws of gypsum board. The second is to prepare tools, which need to prepare various measuring tools, ladders, electric drills, grinders and other tools.

Finally, prepare the required materials such as gypsum powder, rivets, wood squares, caulk, etc.

Step 2: Install the wooden square.

Before installing gypsum board, you need to install a wooden square on the wall. Because drywall is fragile, if it is fixed directly to the wall, it is easy to crack. Therefore, first lay a wooden square on the wall, and then fix the plasterboard on the wooden square.

The spacing of the wooden square is generally about 60 cm, and it can also be adjusted appropriately according to the specific situation.

Step 3: Rivet fixing.

When installing drywall, it is necessary to use rivets to fix it to the wooden square. The number of rivets should be sufficient, generally at least four rivets need to be fixed for each wooden square, and the fixed position should be uniform. If the rivet is of poor quality, too small or too long, it is easy to cause the plasterboard to crack or not fix it firmly.

Step 4: Caulking.

After the plasterboard is secured, the gaps between the plasterboard need to be filled with caulk. Caulk needs to choose a good brand to avoid allergies and other situations. The caulk should be filled evenly, the thickness should be equal, and the caulk should be fully dried before entering the beam and returning to the next step of grinding.

Step 5: Polishing.

Once the drywall is installed, it needs to be sanded to achieve a smooth effect. Grinding is carried out with a grinding machine, in a sequential manner, first grinding the edge positions, then the details, and finally a full smoothing work.

Precautions: Oak is hungry.

1.When installing gypsum board, it is necessary to pay attention to fixing, otherwise it is easy to crack and other situations.

2.Choose a good brand of caulk and make sure it is fully dried before proceeding to the next step.

3.Be patient when sanding drywall and follow the sequence to achieve a smooth, smooth finish.

4.During the construction process, it is necessary to pay attention to safety, wear gloves, masks and other protective equipment to avoid inhaling dust and causing injury.

In conclusion, installing drywall requires preparation and following the steps. At the same time, it is necessary to pay attention to safety issues during construction. Only in this way can we obtain a beautiful and practical decoration effect.