What should I do if the electric oil lamp does not light up and does not heat

1. First of all, it is necessary to judge whether the wiring of the electric heating oil is intact and whether there is any disconnection, and 2. Check whether the temperature control twist is on. According to you, the phenomenon basically belongs to these two reasons.

Determine whether the power switch is broken, overheat protection shutdown and power tripping, because these are common faults and easy to repair. If the internal heating element is broken and cannot be repaired by itself, it must be sent for repair.

The electric heating oil is contained in the heat transfer oil, the heating pipe is immersed in the heat transfer oil and transmitted to the whole radiator through the heat transfer oil, in order to ensure that the heating pipe is not dry burned when heating, so the oil is equipped with an anti-dumping switch, when the oil is poured, the switch will disconnect the power supply and protect the heating pipe, remember to unplug the power plug before maintenance.

The reason why the oil heater is not hot - the body of the oil heater is faulty 1, the power cord in the oil heater is broken, especially the joints;

2. The power cord of the electric heater is damaged or the power plug is damaged;

3. The power switch of the heater is damaged or the contact of the temperature control knob is too dirty or the contact is ablated;

4. The electric heater is damaged, but this situation is rare.

Solution: Do not disassemble and dispose of it yourself to prevent safety accidents, in this case, it is best to go back to the factory to rebuild or find a professional master for maintenance.

The electric oil is not heated, and the indicator light is not on, first check whether the insurance inside the electric oil lamp is burned out, and secondly, check whether the anti-dumping switch inside the electric oil lamp is not completely closed or oxidized? The second is whether there is too little oil inside the electric oil lamp.

The electric oil is not heated, after making sure that you are plugged in without a problem, there are three reasons, the first is the problem of the oil line, try to change the cable. The second is that the switch is broken, the light is not lit and not heated, you can change the switch, and the ones sold on the Internet are not expensive, and you can replace them yourself. The last one is complete, the heating wire of the oil is broken, and this cannot be repaired, so it can only be replaced with a new one.

Hello, three possibilities.

1. The switch that dumps the power off is broken.

2. The heating element is damaged.

3. The thermal protection element is damaged.

The reason why the electric oil is not hot:

1.Check whether the power plug, socket, etc. are in poor contact, and whether the power cord is open. If so, all you need is to replace a good, qualified power cord, plug or socket, etc.

2.If there is a short circuit, first eliminate the source of the short circuit, and then replace the over-temperature dissolver.

3.If the thermostat or switch is damaged, use a multimeter to measure and judge, and then repair and replace the damaged components.

4.Both electric heating pipes are damaged at the same time and can be replaced as a whole.

5.If your electric heater is half hot at the bottom and half is not hot at the top, it means that there may be a shortage of oil, and you can change the oil yourself.

6.Check whether the anti-dumping switch is faulty, and if the dumping switch is damaged, replace it with a new one.

Inside the general electric oil ding, there is an anti-dumping switch, check whether the switch is abnormal or the switch is not completely closed, so there will be a situation that the indicator light is not heated, secondly, check whether the temperature sensor is normal? If it is not normal, the electric oil will not be able to heat up normally.

You can turn on his line in the case of a power outage and check whether the line is normal or whether the line has a virtual contact.

Generally, there is an anti-dumping switch in the electric oil, check whether the switch is abnormal or the switch is not completely closed, so the indicator light does not heat up, and then check the electric oil, if the temperature sensor is normal, the electric oil is also destroyed.

Summary. 1. The first consideration is overheating protection, this situation is more common, that is, the thermal protection element inside the oil tin is damaged, and it is precisely because of the working mode and principle of the oil tin, so the safety element will be installed and designed inside the oil tin, when the temperature of the oil tin reaches a certain critical value, the switch will be automatically turned off, the power supply will be disconnected, and the oil tin will stop working, until the temperature drops to a value, the oil tin will be turned on again; There is also an anti-dumping safety switch, when the body of the oil tin is in a lodging state, in order to avoid dangerous accidents, the oil tin will immediately start the protection program, cut off the power supply, stop working, at this time we must straighten the machine, in order to 2, check the voltage in the house, to see if the voltage is normal, if the voltage is in a continuous or intermittent low-voltage transition, then the oil tin will not work normally, and will not be heated or heated more slowly. 3. Carefully check whether it is due to long-term use, resulting in insufficient oil inside the oil tin, generally this situation will not exist, unless the oil leakage of the oil tank and the diversion pipe, carefully check, after repairing, add professional oil.

Oil heating + light on + not hot.

This must be a failure, if you can't do it, find someone to fix it.

I'm sorry I don't understand, but can you elaborate on that?

1. The first consideration is overheating protection, this situation is more common, that is, the thermal protection element inside the oil tin is damaged, and it is precisely because of the working mode and principle of the oil tin, so the safety element will be installed and designed inside the oil tin, when the temperature of the oil tin reaches a certain critical value, the stove will be automatically turned off, the power supply will be disconnected, and the oil tin will stop working, until the temperature drops to a value, and the oil tin will be turned on again; There is also an anti-dumping safety switch, when the body of the oil tin is in a lodging state, in order to avoid dangerous accidents, the oil tin will immediately start the protection program, cut off the power supply, stop working, at this time we must righten the hidden stove loss, in order to 2, check the voltage in the house, to see if the voltage is normal, if the voltage is in a continuous or intermittent low-voltage transition, then the oil tin will not work normally, and it will not be heated or heated more slowly. 3. Carefully check whether it is due to long-term use, resulting in insufficient oil inside the oil tin, generally this situation will not exist, unless the oil leakage of the oil tank and the diversion pipe, carefully check, after repairing, add professional oil.

Summary. Hello dear, glad to answer for you! <>

The electric oil lamp does not light up and does not heat because the thermal protection is shut down and the power supply trips. The electric heating oil is contained in the heat transfer oil, the heating pipe is immersed in the heat transfer oil and transmitted to the whole radiator through the heat transfer oil, in order to ensure that the heating pipe is not dry burned when heating, so the oil is equipped with an anti-dumping switch, when the oil is poured, the switch will disconnect the power supply and protect the heating pipe, remember to unplug the power plug before maintenance. <>

What should I do if the electric oil lamp does not light up and does not heat

Happy dear to you, happy to answer for you! <>

The reason why the electric heating oil is not lit and does not heat is because the thermal protection is shut down and the power supply is tripped. The electric heating oil is contained in the heat transfer oil, the heating pipe is immersed in the heat transfer oil and transmitted to the whole radiator through the heat transfer oil, in order to ensure that the heating pipe is not dry burned when heating, so the oil is equipped with an anti-dumping switch, when the oil is poured, the switch will disconnect the power supply and protect the heating pipe, remember to unplug the power plug before maintenance. <>

<> kiss <>

Related expansion: Oilfilledradiator, also known as oilfilledradiator, is a safe and reliable space heater that is currently popular. These heaters are usually fitted with a bimetallic temperature control element that disconnects itself when the oil temperature reaches a set temperature.

Advantages: The main feature of this heater is that it emits a large amount of heat, and even in the case of a sudden power failure, it will maintain a certain temperature for a long time, and it does not produce any harmful gases and no electrical operation noise. The surface temperature of the electric oil heater is low, generally not more than 85, even if it touches the human body, it will not cause burns, and it is suitable for heating in places where the human body may directly touch Hengtang.

<> It is mainly composed of sealed electric heating elements, metal heating tubes, iron heat sinks, temperature control components, power switches, and Shenna indicators. This kind of heater is to install the electric heating pipe inside the cavity of the heat sink, and the heat transfer oil is injected around the electric heating pipe in the cavity. When the power is turned on, the heat conduction oil around the electric heating pipe is heated and rises to the upper part of the cavity, and the blind group is instructed to circulate along the convection of the heat pipe or heat sink, and radiate the heat out through the surface of the cavity wall, thereby heating the space environment.

The air-cooled heat transfer oil descends around the electric heating pipe and is heated again, starting a new cycle. <>

1. The second door interlock switch is broken: the reason for the damage of the second door interlock switch is that the 220 volt working voltage cannot work normally due to frequent operation, poor contact, and electric shock destruction. Workaround:

Check whether the fuse is blown first, and then see if the monitoring switch is normal, if it is normal, it means that the interlock switch is broken. Replacing the switch will do the trick.

2. The high-voltage transformer is damaged: if the light is on but the turntable does not move after starting, it means that it cannot be heated, and if it is normal, the high-voltage transformer can be replaced.

3. The magnetron is broken: The damage of the magnetron is mainly manifested in the fact that the boot light is on but not heated, and the reason for this is generally due to the aging of the magnetron inside, and the filament is broken. Workaround:

When inspecting, talk about high-voltage capacitor discharge, test filament winding, normal is 0 ohm, if not so, it means that the magnetron is broken, just replace it.

4. The high-voltage diode is broken: this situation is also often occurring, the disk is rotating, but it is not heated, if it is so, it is necessary to test whether the filament winding is normal when overhauling, if it is normal, it is necessary to look at the high-voltage diode to see if it is normal, if the test is uniformly infinite, at this time it is necessary to change the high-voltage diode.

The light is not on, it may be a problem that the power circuit is not working, as long as the electric heating pipe is good, the problem is not big, check the power cord to see if there is a problem.

If you don't call, just change the power cord.

2.The heating element is damaged.

3.Thermal protection elements are damaged.

Therefore, if the oil does not heat, in addition to the damage of the heating element, it is also possible that the dumping power-off switch is broken, or the thermal protection element is damaged.