What are the different methods for installing and removing the hook?

Dry the grease and moisture on the surface of the object, then use a lighter to bake and melt the glue behind the hook, press the surface of the object, and you can hang the item after five minutes. In addition, the product comes with two spare glue in the package, if you want to change the hook, first use a knife to stick to the back of the hook to cut, and then use a lighter to melt the prepared rubber particles on the back of the hook and stick it wherever you want to glue. First of all, the place to be glued must be a flat surface, and then wipe the surface of the object clean, no dust and debris, if you want to stick to the glass and tiles, take a little egg white on the surface of the sticky plate and wipe it evenly, and finally press the sticky plate on the position to be glued.

When pasting, don't let the surface of the object be too dry, it will affect the effect of pasting, and wet spots are best). Removal method: First of all, choose a *** sticky hook.

There are several kinds of suction cup sticky hooks sold in large supermarkets to choose from: non-marking sticky hooks, which are patented and easy to identify.

Relying on physical leverage to strengthen the exhaust air, the purchase is carefully read the instructions should also be found. The air is removed by rotating the pressurized gland. Sticky hooks, glued to paste.

Among them, the first three are reusable, so they will be slightly more expensive, and the fourth is disposable, which will affect the beauty of the wall. Secondly, during installation, you can wipe the wall clean with water (the wall is best tiled or mirrored, the higher the finish, the better), and then install it after it is completely dry. Tools:

Knife, wind oil, rag, boiling water steps: Use a hair dryer to blow hot air for a while, and the viscose will soften. Then use a wallpaper knife to carefully stick to the door to cut a small incision, and then slowly lift it up.

If there is a little residue, you can sandpaper it. The first step is to cut the sticky hook from the top along the back of the hook closest to the sticky side, taking care not to hurt your hands; In the second step, soak the corner of the rag with boiling water and wipe vigorously. It must be boiling water, the effect is better.

Be careful not to burn yourself; In the third step, apply the wind oil essence to the rag and use it to vigorously wipe the remaining gum. Because the wind oil essence is slightly corrosive, the glue removal effect is obvious, and it is a good way to remove the remaining gum from the sticky hook.

Soak in hot water for a while, then you can remove it. Use a hair dryer to blow the glue and bake it hot. Rub it with wind oil essence, and it will fall off after a while, try it.

You can give the eraser a try. But at the beginning, you may feel that the more you rub, the dirtier it gets, but if you wipe it for a longer time, you will see the effect. Soak it in water, put a little dish soap, and brush it with an old toothbrush.

It is also possible to wipe it with a cloth dipped in alcohol or a second pot head. You can buy a liquid that removes marks from adhesive paper, which is usually sold in car specialty stores. It works well.

Use a viscous transparent glue to repeatedly stick and tear, you can remove some of the surface and wipe it with a cotton swab dipped in nail polish remover. Wipe with a special cleaner or sneaker stain remover.

Wipe the tiles clean (if it's cooler, warm the walls with a hot water bottle or other heat source, being careful not to stain the tiles). Glue the hook. Hammer with a small hammer.

Wait 24 hours before hanging something. Note: When there is oil, dirt or wax on the adhesive surface, please wipe it off with alcohol or organic solvent before bonding.

If the surface of the mounting site is not clean, it will reduce the firmness of the sticking hook. When the hook is used, it should be hung vertically to avoid violent shaking of the side pull. Please do not exceed the weight limit.

Please do not hang up within 24 hours after installation. In winter, use a heater to slightly heat the contact surface. If there are water droplets, water can easily splash, please do not use electric stoves, stoves, etc.

Initial attempt by hand: When taking a strong sticky hook, you can first use your hand to take the sticky hook to see if it can be removed, and pay attention not to use too much force in this process to prevent damage to the wall.

Please click Enter a description.

Use a hair dryer. Blowing: If the stickiness is too big and can't be removed by hand, you can use the high temperature of the hair dryer to blow on the sticky hook to be taken off for 2-3 minutes (the specific time is subject to the softening of the viscose), and after the viscose softens, you can take off the sticky hook first.

Please click Enter a description.

Scrape with a blade: After the sticky hook is removed, there may be glue marks, at this time, use a knife to slowly hang up the glue marks on the wall little by little, pay attention and do not scratch the wall, you can also spray the toilet water first.

Then scrape with a spatula.

Please click Enter a description.

Apply toilet water: After feeling that it is almost scraped with a knife, spray on the toilet water and soak for 10-20 minutes.

Please click Enter a description.

Wipe with a rag: After soaking in the toilet water, wipe the glue marks with a rag to wipe off the glue marks, if it is on a wooden wall, you can repeatedly apply the toilet water 2-3 times in a row, and wipe with a rag.

Please click Enter a description.

Suggestion: In the process of cleaning, it is necessary to scrape, wipe lightly, and repeat many times to prevent excessive force from damaging the wall, and the gains outweigh the losses.

Please click Enter a description.

end precautions.

Flower water can also be used with white vinegar or wind oil essence. In lieu of.

Hello dear! Self-adhesive hook removal method 1The hair dryer is first plugged into the power supply of the hair dryer, then adjusted to hot air mode, and blow dry starting from the edge of the hook sticker to dry the glue on the hook sticker, and then pry it open with a knife.

2.Apply vinegar to drip the vinegar off the edges of the sticky hook sticker. The acids in the vinegar react with the glue, which reduces the stickiness of the sticky glue.

The hook tag can then be easily removed without leaving any marks on the wall. 3.The dishwashing liquid is first soaked completely by placing a damp towel on the hook sticker, then applying detergent to the hook sticker and scrubbing it with a discarded toothbrush.

Wait for the cleaner to easily infiltrate the hook tab, which will cause the hook tag to come off.

<>1. Remove the strong sticky hook with a hair dryer heating, first determine the position of the hook on the tile, then adjust the blowing chain branch fan to the maximum heat, blow it at the bottom of the hook for about 5 minutes, and finally scrape it off with a thin line of Douqing.

2. You can also spray some white vinegar around it, and you can take it off after a while.

3. There will be glue marks after the sticky hook is taken out of the air and held down. You can mix turpentine, soapy water and ammonia to wipe the glue marks and wipe them clean.

Sticky hooks are common gadgets in our lives, sticking hooks on the wall, bags, towels, and various small objects can be hung if you want, which is both space-saving and convenient. But when the hook is broken, old, and needs to be replaced with a new hook, it is really not easy to completely remove the sponge glue traces left by it, so how to remove the sticky hook?

1. Along the side closest to the wall on the back of the hook, peel off the main body of the hook from the wall with a small blade, and be careful not to hurt your hands.

2. Then soak the corner of the rag with boiling water to wipe the glue left on the wall. Because the glue will soften and be better removed when exposed to heat, it is recommended to use boiling water for better results.

3. Apply the wind oil essence to the rag, and then wipe the remaining gum. Because the wind oil essence is slightly corrosive, the effect of removing gum is obvious.

If you want to remove the hanging hook smoothly, then you can operate through the above methods, I hope it can help you.

The sticky hook must be as smooth and flat as possible to increase the contact area between the sticky substance and the wall as much as possible. Many people know this. But what many people don't know is that before sticking the hook, be sure to wipe the wall clean with a damp cloth to remove dust, and then wipe off the moisture with a dry cloth (or paper towel).

Dust on the wall will greatly destroy the stickiness of the hook and cause the hook to fail.

Once you're done, hold the hook with your hand for at least 1 minute (in theory, the longer the better, of course). Be sure to make sure that the sticky substance and the wall are adequately bonded, many people stick and then let go, which is not enough.

In general, after gluing the hook, you will leave the hook and the wall alone for at least 24 hours, and if you want to work well, 48 hours is better. Many people are in a hurry to hang things as soon as they are glued, and this time give the sticky hook a force, so that the sticky material leaves the wall and cannot be fully integrated. Therefore, giving the viscous substance at least 24 hours will give the effect better.

1. Wipe the adhered surface with a clean soft cloth and must be fully dried.

2. Do not touch the adhesive surface with your hands when uncovering the isolation paper.

3. Tighten tightly when bonding.

Take care when using.

1. When there is oil, dirt or wax on the adhesive surface, please wipe it with alcohol or organic solvent before bonding.

2. If the surface of the installation site is not clean, it will reduce the firmness of the sticky hook if it is not dry.

3. When the sticky hook is used, it should be hung vertically to avoid violent shaking of the side pull.

4. Please do not exceed the weight limit of the hanging object.

5. Please do not hang within 24 hours after installation.

6. When sticking in winter, please use a heater to heat the contact surface slightly.

7. If there are water droplets, water is easy to splash, please do not use electric stoves, stoves and other places.

You can use a hair dryer to blow after heating with a hair dryer, or use a knife to scrape, in fact, there are now that kind of hooks are sucked, you can buy that kind.

It is really convenient to blow it with a hair dryer, and then you can scrape it off little by little with a knife, preferably on the tile.

I usually use a hair dryer to blow it, and after a while of hot blowing, the glue will melt off, and then I can easily take it off.

The glue of the hook can be cleaned by buying wax on the surface plate or by buying a special cleaning agent for cleaning the glue.

When the hook starts to be hung up, it can be scalded with fire, so that it will be more bonded.

Another detergent that specializes in removing glue can also be better removed by covering it with hot water.

The viscose of the hook actually has a special cleaning agent, you can buy it to try, I forgot what it is called.

You can blow it with a hot air dryer and dry it, or use some of that kind of wax, I don't know exactly what wax is, but I've heard that it's very easy to use.