How to make a mop, how to make a hand mop?

Teach you how to make your own mop.

Here's how to use the mop:

1. The use of the mop is very simple, first soak the mop head with water, wring out the water, make the mop in a wet state, and then mop the floor.

2. There are often all kinds of stains on the floor, and after cleaning up the garbage with a broom, you need to mop the floor clean. Mops are a cleaning tool that needs to be used in every household, and with continuous development, the types of mops have also become diverse.

3. After mopping the floor, the stains on the floor will gather on the mop, if it is not cleaned, it is easy to breed microorganisms and bacteria, and when mopping the floor again, it will bring microorganisms and bacteria to the floor, affecting health, so the mop needs to be cleaned after each mopping.

Precautions for using a mop

1. In order to prolong the use time of the mop, it is best to sweep the hair and dust before mopping.

2. The direction of mopping the mop should follow the texture of the floor as much as possible, so that the dirt can be removed and the cleaning effect can be achieved.

3. It is best to wash the mop with running water to rinse it will be cleaner, if you have the habit of using floor cleaner, the dirty mop can be washed off under the faucet, and then put it into a bucket filled with detergent to soak it, and then wring out and mop the floor.

4. Pay attention to the use of various types of mops, and use the right method to improve the efficiency of mop use, for example, some rubber mops need to be soaked in water before use.

5. Use a mop to wipe the wooden floor, try not to use a mop with high water content, such as a rubber wool mop. Because the surface of the wooden floor has pores, it is easy to absorb water vapor, which causes the floor to be deformed and fragile, and shortens the life span.

Prepare tools: mop cloth, mop rod, wire, scissors.

1. First of all, prepare the required materials, as shown in the figure below

2. Take the mop cloth, as shown in the figure below

3. Wrap a strip of cloth in the middle, as shown in the figure below

4. Take the mop cloth close to the direction of the mop rod to the other side, as shown in the figure below

6. Take the wire and hold the head, and then twist it a few more times with pliers, as shown in the figure below

6. Finally, lift the tied mop vertically, as shown in the figure below

Prepare tools: mop rod, mop cloth, wire, pliers, scissors.

Steps. First, first of all, prepare the materials and supplies for tying a mop. As shown in the figure below:

Steps. 2. Take the mop cloth, measure it into a length of one meter and two and put it neatly. As shown in the figure below:

Steps. 3. Put the lower end of the mop rod in the middle of the mop cloth, and wrap it in the middle with a strip of cloth. Note that there is a round hole under the rod that can be fixed with a wire. As shown in the figure below:

Steps. 4. Take the mop cloth close to the direction of the mop rod to the other side, and spread it evenly around the edge of the mop rod, and then use a strip of cloth to wrap it at the upper end. As shown in the figure below:

Steps. 6. Hold your head with a wire, and then tighten it with pliers. As shown in the figure below:

Steps. 7. Finally, cut them together with scissors. As shown in the figure below:

Ingredients: old sheets, old clothes, old mop rods, wires, scissors, hammers, pliers.

Steps: 1. Use scissors to cut the old bed branch mold into strips with a height of about 80 cm and a width of about 5 cm.

2. Use a hammer to fix a nail at one end of the mop rod and tie one end of the wire.

3. The strips of cloth are doubled and strung one by one to the wire.

4. Finally, wrap it up like this, and wrap it tightly with two circles of wire.

Pay attention to the liquid: Finally, tie it a few more times with the wire, and the tie will not fall off.

How to make a simple mop at home.

Prepare tools: mop cloth, mop rod, wire, scissors.

1. First of all, prepare the materials and supplies for the mop. A mop rod, an appropriate amount of mop cloth, 20 cm of wire, a pair of pliers, and a pair of scissors.

6. Hold the head with a wire, and then twist it a few more times with pliers, the tighter the better. The previous tape is no longer useful and can be removed.

6. Finally, lift the tied mop vertically, and there are many uneven strips of cloth at the bottom, as long as you cut them with scissors.