Jim Fern leaves are dry, why are there some hairs on Jim Fern leaves

Just cut off the dry branches and leaves. It is generally pruned in early spring to promote new growth, and some yellowing and wilted leaves should be cleaned up in time to promote the growth of new leaves. in the canopy.

At the bottom, you can see some rolled up, or cross-grown leaves, which should be cut off in time to avoid over-dense planting and affect ventilation and light transmission.

To ferns.

When pruning, be sure to use sharp scissors, it is best to disinfect in advance, which can reduce the breeding of pests and diseases, and the other is to raise it in a cool place for a few days after pruning, and then slowly see the light, pay attention to maintaining humidity and environmental ventilation.

Summary. Hello dear ! The hairiness on the leaves of the Jim fern is due to the fact that they have a lot of small hairs on their leaves, which help them resist changes in the environment, such as temperature changes, humidity changes, and prevent water loss.

In addition, these fluffs can also help them fight off pests and diseases, preventing them from being damaged. In addition, these villi also help them collect more sunlight, which increases their photosynthesis, which increases their growth rate. In conclusion, the hairs on the leaves of the Jim fern are there to protect them, increase their growth rate, and thus make them healthier.

Dear kiss, I hope mine can help you! (-

Hello dear ! The hairiness on the leaves of the Jim fern is due to the fact that they have a lot of small hairs on their leaves, which help them resist changes in the environment, such as temperature changes, humidity changes, and prevent water loss. In addition, these fluffs can also help them fight off pests and diseases, preventing them from being damaged.

In addition, these villi can also help them to collect more sunlight, which in turn increases their photosynthesis, which in turn increases their growth rate. In conclusion, the hairs on the leaves of the Jim fern are auspicious to protect them and increase their growth rate, thus making them healthier. Dear kiss, I hope mine can help you!

Excuse me, but please go into more detail?

Answer: Hello, it's a pleasure to have your question The hairs on the leaves of the Jim fern are due to the many small protrusions on their epidermal cells that absorb moisture from the air, thus protecting the leaves from drought. In addition, these hairs can also help protect the leaves from pests and diseases, as they can prevent the slippery invasion of pests and diseases, thus protecting the leaves from damage.

In addition, these hairs can also help protect the leaves from wind and rain, as they can reduce the impact of wind and rain, thus protecting the leaves from damage. In conclusion, the hairs on the leaves of the Jim fern can help protect the leaves from drought, pests and diseases, and wind and rain, thus protecting the leaves from damage. I hope I can help you (-.)

1. The most suitable growth temperature is between 18 and 26 degrees Celsius;

2. It is not resistant to high temperature or cold, and the temperature cannot be lower than 5 degrees Celsius when the shed collapses in winter;

3. Like loose soil, watering is based on the principle of not drying and not watering, and watering is watered thoroughly;

4. If you don't like fat, choose thin liquid hand fat.

Summary. There is no need to cut the roots when repotting the Jim fern, just cut the leaves and stems that are old and dead, not the roots.

There is no need to cut the roots when repotting the Jim fern, just cut the leaves and stems that are old and dead, not the roots.

Can you add, I don't quite understand it.

The Jim Fern is a popular foliage plant that is often used to decorate indoor environments. Hail repotting is very important for Jim ferns because they need enough space to flourish. Generally speaking, Jim ferns do not need to be pruned when repotting, but sometimes if the root system is too intertwined, it may be necessary to prune the dead roots to prevent the growth of pests and diseases.

However, it is prudent to cut the roots, scissors should be used, leaving healthy roots, and giving sufficient water after cutting to allow the Jim fern to return to growth. In general, it is not necessary to prune the roots for every repotting, and only in cases of necessary hailstorming.

Summary. No, GMO doesn't need to cut the roots, just dig up the soil from the roots and put it in a new pot.

No, GMO doesn't need to cut the roots, just dig up the soil from the roots and put it in a new pot.

Can you elaborate on that a little bit more?

Reasons for the problem:1The root system of the Jimmau plant may have been too large and has exceeded the capacity of the original pot, so it needs to be repotted.

2.The root system of the Jimmao plant may have grown too long and exceeded the capacity of the original pot, so it needs to be repotted. Workaround:

1.Before repotting, a part of the root system should be cut off so that the plant can better adapt to the new pot. 2.

Before repotting, the plant should be removed from the original pot and the root system should be cut short so that the plant can better adapt to the new pot. Personal Tips:1

Before repotting, the root system of the plant should be carefully inspected to determine if a part of the root system needs to be cut off. 2.Before repotting, the size of the new pot should be determined so that it is necessary to determine if a part of the root system needs to be cut.

1.The root system of the Jimmau plant needs plenty of space to grow, so you should choose a larger pot than the original pot when changing the pot. 2.

The root system of the Jimmau plant needs plenty of space to grow, so you should choose a larger pot than the original pot when repotting, and you should provide enough water and fertilizer for the plant.