What is the reason for the abnormal noise of solid wood flooring? How to solve it?

Wooden floors are prone to some problems after being used for a long time, such as making noises. So, how to deal with the squeak of the wooden floor when you step on it? What should I pay attention to when using wood flooring?

Why does the wooden floor squeak when stepped on, how to deal with it.

1. The weather is dry.

In drier weather, the adhesion between the wood floor and the wood floor will decrease, and the joints will start to loosen, and we will squeak when we step on it.

In this case, when the weather returns to normal, the floor will no longer rattle. However, if the noise persists, the loose wooden floor needs to be re-paved to ensure that it is tight.

2. Loosening between wooden floors.

If there is a sound and there is no sound, it is basically caused by the loosening between the wooden floor and the wooden floor, such as a gap in the groove. If the sound is continuous when stepping on it, it is caused by the floor and the wooden tenon not being firmly connected. If you want to solve the problem, you need to ask a professional to remove the loose wooden floor, and then re-pave it again as required, and firmly connect the floor with the wooden tenon.

3. The ground is uneven.

If the floor is not leveled, the wooden floor will also make a creaking sound when stepped on after installation. It is necessary to remove and clean the noisy part of the wooden floor, level the ground in this part, and finally install the wooden floor.

Precautions for the use of wooden flooring.

1. Cleaning the wooden floor must not be sprinkled directly on it, be sure to use a squeezed wet rag or wet mop to wipe and clean, directly sprinkled on the wooden floor will affect the service life of the wooden floor, and there will also be the problem of warping the wooden floor.

2. If you want to continue to use the wooden floor after warping, then you need to pry the wooden floor open and put it in the sun for drying before it can be reinstalled and used, but in this case, the surface of the wooden floor has been damaged, and the possibility of deformation is also very large, and its service life after it will not be particularly long.

Disclaimer: This article is for the purpose of conveying more information. Do not bear any legal responsibility, if there is any infringement, please contact us, we will delete it as soon as possible.

The pavement floor is uneven The ground of the stage wooden floor is not leveled before paving, resulting in the phenomenon of cracks on the floor, and the squeak of floor friction will be heard when stepping on it. Solution: Before the stage wooden floor is paved, the ground must be leveled, usually with self-leveling and leveling.

The abnormal noise of the solid wood floor may be caused by poor quality, and in this case, you can go to the merchant.

The reason for the abnormal noise on the solid wood floor is that there may be a gap under the ground, and we should check that there is a sound to solve it as soon as possible.

The home decoration made by the floor is indeed welcomed by everyone, but the sound of the solid wood floor makes many consumers worry, which may occur just after the decoration, or it may occur after a period of time. The following is an introduction to a new process of laying flooring, which can effectively solve such problems.

Tools: Raw Materials, Elastic Wire, Keel, Hand Drill, Hammer, Expansion Spike.

Method Step 1: Floor laying, keel is key. The initial ground is uneven.

Therefore, the thickness of the keel will be adjusted accordingly. Tongji decoration construction personnel will mark a keel elevation line close to the ground, which is also the horizontal line of the finished surface of the keel, and control the thickness of the keel according to this elevation line. 2：

The thickness of the keel will generally be more than the horizontal line of the finished surface. After the ground keel is laid. The construction personnel will play the line according to the actual level of the finished surface.

The elastic line is to determine the actual joint surface of the keel and the ground, in order to make the two more closely combined, the carpenter will do the corresponding processing according to the elastic line, and the keel can be finally formed. 3: The upper limit of the length of each keel is 4 meters, if the room is longer, beyond the upper limit of 4 meters, the construction personnel will use the method of splicing, and the splicing will be spliced with oblique seams.

4: The construction personnel will first drill holes in the keel with their hands. When making a hole, you should first make a hole in the joint of the two keels and fix it.

After the hole is drilled, a hammer is used to hammer the nylon expansion nail into the hole and finally fix. The toughness of the expansion nail used by Tongji is good, and the length is generally 8-10 cm 5: When the keel is laid, it must be seamlessly connected with the ground, and the construction personnel will fix it with a supporting keel to ensure that the keel is densely combined with the ground.

1.The most direct and effective method, many netizens have tried, sprinkle talcum powder in the cracks of the floor, which can help lubricate and have a certain effect. In addition, some people will use laundry detergent, soak it in water, and then inject it into the seams of the floor, which can have a certain effect.

However, these two methods can solve the problem of relatively small sound.

2.The most fundamental solution is to solve the keel problem under the wooden floor, for example, if the keel is loose, we need to re-nail the nails to strengthen the nail grip force, and at the same time the tenon and groove of the wooden floor should be tightened to avoid the expansion problem caused by the humid air.

3.At the same time, when relaying the wooden floor, it is also necessary to pay attention to the gap between the wooden board and the wooden board to leave a little larger to prevent the problem of thermal expansion and cold contraction of the arch.

1. The sound caused by the uneven ground of the solid wood floor installation is very common, mainly because there is no leveling when installing the solid wood floor, and the suspension is generated between the floor and the keel or the wooden keel is not cushioned to produce suspension, which is the reason why the sound will appear when walking on the solid wood floor after the installation is completed.

Solution: The solution to this situation is that if it is a small part, you can carry out essential oil penetration treatment on the part of the floor to improve, and if it is a large area, it is recommended to disassemble and reinstall.

2. The difference in dryness is large, and the keel produced by some manufacturers is stacked casually before drying, resulting in a large difference in the moisture content of the wooden keel, so that even in the process of floor installation, the installer leveled the wooden keel, and there is no problem of floor sound after the floor installation is completed, but after a period of use, the wooden keel will still lose its balance again because of the change in moisture content, resulting in the appearance of floor sound.

Solution: To avoid this situation, the main thing is to let the wooden keel sit indoors for a week before the floor is installed, so as to effectively reduce the occurrence of this situation.

1. The sports wooden floor is empty.

If the sports wood floor is empty, there are many reasons, one is that the sports wood floor is not fixed when it is laid, the main reason is that the number of nails used is not enough, or it may be that the nails are not firmly nailed. The sports wood floor sports system is fixed with glue liquid, and the gluing does not meet the requirements will also cause the sports wood floor to be empty.

The reason for the abnormal noise of the sports wood floor is that the moisture content of the sports wood floor used by Sakura can be changed.

2. Prevention of air wages on sports wood floors.

In view of the common causes of sports wood floor empty salary, one by one elimination and prevention, can effectively prevent sports wood floor empty salary.

When laying sports wood flooring, nails can not be used too little, laying process, each completed piece, to step on a foot to inspect the mess, if there is a sound to rework and then paving.

When purchasing and paving sports wood flooring, it is necessary to strictly check its moisture content, and the quality of the adhesive must also be strictly reviewed.

Many people have installed solid wood flooring at home, but sometimes solid wood flooring will make abnormal noise, today PCHOUSE will introduce to you the solution to the sound of solid wood flooring.

Measures to prevent noise before and during paving:

1) Check the quality of the floor.

2) Check if the ground is level.

3) Measure the moisture content of the keel.

4) Reserve enough gaps when paving, and remember to add gaskets when installing the keel.

The solution to the noise after paving:

1) Silencer can be used for local noise.

2) The muffler liquid cannot be solved, and the noise is too loud, but there are few places where the noise appears, and local repaving can be carried out.

The installation of solid wood flooring is the preferred choice for the installation of floor in many homes, but some owners have reported that there is a sound after the installation of solid wood flooring

Causes and solutions of solid wood flooring:

1. The ground is uneven

The sound caused by the uneven installation of the solid wood floor is very common, mainly because there is no leveling when installing the solid wood floor, the floor and the keel are suspended or the wooden keel is not cushioned to produce the suspension, these are the reasons for the sound of walking around on the solid wood floor after the installation of the solid wood floor, the solution to this situation is that if it is a small part, the essential oil penetration treatment can be carried out on the part of the floor sound to improve, if it is a large area, it is recommended to disassemble and reload.

2. There is a big difference in the dryness of the keel

The keel produced by some manufacturers is stacked casually before drying, resulting in the moisture content of the wooden keel is too different, so that even in the process of floor installation, the installer leveled the wooden keel, and there is no problem of floor sound after the floor installation is completed, but after a period of use, the wooden keel will still lose its balance again because of the change of moisture content, resulting in the appearance of floor noise. To avoid this situation, the main thing is to let the wooden keel sit indoors for a week before the floor is installed, so as to effectively reduce the occurrence of this situation.

3. Keel looseness

Some workers use the fixing method of beating the wooden wedge and adding iron nails in the installation and construction of solid wood flooring, which will cause the nail holding force to be insufficient because the contact surface between the wooden wedge and the iron nail is too small, and it is easy to cause the wooden keel to loosen, and there will be a sound when stepping on the floor. This needs to be discussed with the construction master before installing the solid wood floor, and choose a better keel fixing method.

4. Insufficient gaps in the floor

We all know that there must be enough reserved gaps for the installation of wood flooring, otherwise the expansion process of solid wood floor will produce a slight arch that is difficult to observe with the naked eye, so that there is a gap between the solid wood floor and the keel, so that when walking around, the solid wood floor will rub up and down to produce a sound. This kind of noise is also very common, so in the installation of enough gap reservation, if this really happens, do not hesitate to renovate and reinstall the treatment, generally you can first look at the effect of the solid wood floor after moisture, if the solid wood floor is damp after serious deformation, the solid wood floor squeezed particularly tight state will not make a sound.

5. The moisture-proof film is not cushioned

When installing the solid wood floor, the moisture-proof film is not supported by the cushion, the moisture of the ground will penetrate into the back of the solid wood floor, and the solid wood floor produces a slight tile change and distortion, on the keel, the solid wood floor is like a seesaw, and there will be a sound when people walk, and it is difficult to maintain this noise, and the best way is to reinstall it.

It is a very common problem to make noise when walking around after the installation of solid wood flooring, and the most important thing is that we should prepare for the installation of solid wood flooring, so that there will not be too many problems after installation, which will affect the use of wood flooring.

You can get it for free

Hello dear! Glad for your question! There is an abnormal noise on the floor:

Phenomenon 1: The climate is dry or wet, and the reason for the sound: the excessive drying of the climate weakens the nail holding force of the floor and keel, and the connection between the floor tenon and groove is loosened; Excessive humidity causes the floor to expand laterally, resulting in expansion that slightly squeezes the arch and loosens the keel fixation.

Solution: If the climate is too humid or dry, you can wait until the climate is normal to observe. If there is no obvious sound, there is no need to trim it.

Phenomenon 2: The sound comes and goes for no reason: if you step on it somewhere, sometimes there is a sound, sometimes there is no sound, this situation is mostly caused by the floor nail is smaller than the drill hole of the solid wood floor, and there is a loose gap between the male and female floor.

Solution: When installing solid wood floor drilling, the hole diameter must be smaller than the floor nail, so that the floor can eat nails. Phenomenon 3:

Step on a foot and ring the reason: If you step on a foot and sound again, and then step on it again, and it is like this continuously, it must be that there is no fixed between the wooden dragon and the wooden tenon on the ground, or the wooden tenon material is too soft and not difficult, and it is pulled up by the ground dragon. How to deal with it:

The material of the wooden tenon of the rammed ground is harder than the material of the earth dragon, and the hard shrinkage force of the wood is small, and the earth dragon is not easy to pull up the wooden tenon elastic to maintain stability.

Summary. Solid wood floor creak squeak solution tricks: pro solid wood floor creak squeak solution tricks are as follows: if because the floor is pressed with heavy objects, because it cannot expand freely, resulting in the ground arching, at this time people walk, it will make a sound, this situation can be alleviated by directly moving the heavy objects away.

If the floor is damp and the floor is arched, if the situation is not serious, the damp floor can be removed to dry, or the dehumidification function can be turned on regularly every day to keep the floor dry. If the floor has been used for a long time, you can apply wax to the gaps in the floor, and then melt the wax at high temperature and penetrate into the gaps.

Solid wood floor creaking squeak solution tricks: Liang Mo pro solid wood floor creaking squeak solution tricks are as follows: If the floor is pressed with heavy objects, because it cannot expand freely, resulting in the ground arching, people will make a sound when they walk, and this situation can be alleviated by directly moving the heavy objects away. If the floor is damp and the floor is arched, if the situation is not serious, the damp floor can be removed to dry, or the dehumidification function can be turned on regularly every day to keep the floor dry.

If the floor has been used for a long time due to the macro slag posture, you can apply wax to the gaps of the floor, and then melt the wax at high temperature, and penetrate into the gaps to cover it.

The floor has just been laid, and there is a large area of noise, and what is the reason for it?

1.The ground is uneven due to the uneven ground, after the floor is paved, there is a gap between the floor and the ground in individual places, and the floor moves up and down in the process of people walking, producing a sound. It is characterized by the fact that after the floor is paved, there is a sound immediately when people move around, and the digging wheel is local.

The measures taken are to measure the flatness of the ground before the floor paving, and its flatness should be less than 3mm 2000mm. 2.When the floor is paved, the surrounding reserved gap is insufficient, and the floor is not enough when the floor is paved, resulting in a slight arching of the floor.

There is a gap between the floor and the ground, and there is a noise when people walk around. It is characterized by the fact that it does not make a sound after just laying the pile, and after a period of time, it sounds in a large area, and the wall and the floor have been tightly roofed. The measure is to leave enough gaps around the floor, especially in the doorway, wall kitchen, balcony and other areas to ensure that the reserved gaps are even.

When the pavement length exceeds 8m, it should be treated with partition and bridge.

It is laid with a ground keel, and there are some places where the horizontal line error of the ground keel is within 2mm.

Okay pro.