What is the reason for the surface of the wooden floor

For example: the surface of the floor is wrapped. What should we do in this situation?

Here's why. 1. An oval bulge appears on the edge of the floor with a bulging edge, a single bag appears in the middle of the two floors, and a plurality of bags exists in the middle of the two floors; Some are connected in a piece, showing an irregular distribution in the room. Second, the board surface.

Oval bags appear on the bulging floor surface, and a single bag or multiple bags appear in the middle of the floor surface at the same time, showing an irregular distribution in the room. It is not difficult to find that the causes of the bulge are roughly as follows: 1. Before the installation of the uneven ground or the ground has sand grain wood floor, because the ground is not cleaned, there are some small sand particles on the ground or the ground is too rough, after the floor is installed, in the process of people's stepping, the moisture-proof film and the balance layer on the back of the floor are destroyed, and the moisture of the ground leads to the floor bulging.

2. Improper handling of moisture-proof measures: This kind of situation belongs to improper moisture-proof treatment during installation. On damp floors, if the moisture-proof membrane joints are not tightly glued with waterproof tape, even if the balance layer on the back of the floor is not damaged, the floor is in a humid environment for a long time, and the moisture may still enter the floor after the balance layer is eroded by moisture, causing damage to the floor. 3. Improper use of the bulging phenomenon caused by water ingress at the floor joints (such as:

Heating running water, large area of water ingress, etc.), belongs to the problem of improper use and maintenance of users.

1. On-site inspection.

Sports wood floor maintenance staff, or stadium staff, when they find that the sports wood floor is soaked in water after work, don't panic first, be calm. Inspect the soaking site at the first time to eliminate potential safety hazards, such as whether there are wires, electrical appliances, flammable and explosive materials on the soaking floor, etc.

Then according to the degree of water immersion of the sports wood floor, a solution is formulated.

2. Soak in water lightly.

If the sports wood floor is lightly soaked, the lightly soaked and damp floor can be wiped dry and ventilated. If necessary, disassemble the sports wood floor to observe whether there is water on the ground and observe whether the floor is obviously deformed. If so, it needs to be removed and dried, and reinstalled.

3. Heavy soaking.

Sports wood flooring that is seriously damp or soaked in water for 30 minutes will be deformed, expanded, and lost its luster. Such sports wood flooring is basically scrapped and should be replaced, and attention should be paid to removing the moisture under the floor and drying it.

4. Precautions.

After the sports wood floor is soaked in water, it is important to pay attention to the fact that it cannot be blown by hair dryer, exposed to sunlight, or dried, which will accelerate the serious deformation and damage to the surface of the sports wood floor of the basketball hall.

Disadvantages of wooden flooring: It is not easy to take care of, and it needs to be waxed frequently for maintenance. It is greatly affected by weather and humidity, and it is easy to deform and warp after flooding.

The surface is prone to scratches, which affects the appearance. In addition, good wood flooring** is relatively high. Many people find it more convenient to lay wooden floors at home, because the floor tiles are a little cold after being paved, and the elderly and children at home will easily fall.

<>Moreover, in winter, it is very inconvenient to run directly on it barefoot. In addition, if the floor tile is not paved if we use a slightly low-end floor, the biggest trouble is deformation, especially dampness, such as sprinkling water, or using wet cloth will cause deformation, deformation will appear back to the floor bulging, look ugly solid wood floor material is hard, meticulous wood fiber structure, low thermal conductivity, the effect of blocking sound and heat, with sound absorption, sound insulation, reduce sound pressure, shorten the residual reverberation time function, reduce noise pollution.

Therefore, the wooden floor is most afraid of water, and it is likely to be invalid by blisters, and if the neighbor's house leaks to our house, or their own water leaks, it is easy to damage the wooden floor. At the same time, it is also afraid of moisture, especially humid environment, not suitable for the use of wooden flooring. Of course, I'm afraid of dryness.

If the wood floor is really too old to repair, it is recommended to replace the wood floor. When the composite floor is bulging, the bulging wood block and the surrounding floor can be removed, so that through a period of ventilation and ventilation, the bulging phenomenon can be reduced, if the area is very large to pry up the floor, you need to wait for the ground and keel to be good before installing it back, when installing the floor, the floor treatment that causes a trace amount of tile shape should be immediately removed below the baseboard to cause convection, eliminate moisture, and the board surface slowly recovers the level with the evaporation of moisture. There are also bad ones, like wooden floors, we will always worry about whether the wooden floors will rot, whether they can come into contact with water, and so on.

Today, let's talk about how to deal with the bulging wooden floor? Then there is a bulge, under normal circumstances, it will not automatically return to its normal state immediately, because there is moisture in the middle, even after a summer, it may not return to a flat state, even if the moisture is dry, it will not return to the original flat state.

Improper handling of moisture-proof measures in daily life: if the wetter ground, the moisture-proof membrane connection is not tightly glued with waterproof tape, and the floor is in a humid environment for a long time, then the balance layer is eroded by moisture, and the moisture may enter the floor, causing damage to the floor and causing bulging. During the decoration process, make sure that the glue completely fills the seams.

If it is not filled, it is easy for water to enter through the joints with less glue when mopping, and the floor substrate will absorb water, resulting in local expansion and small blisters.

After the floor was installed, the moisture-proof membrane and the balance layer on the back of the floor were destroyed during the stepping process, and the moisture from the ground caused the floor to bulge.

2. If the ground moisture-proof measures are not properly handled, it will also cause the floor to bulge, in the humid ground, if the moisture-proof film connection is not glued with waterproof tape, although the balance layer on the back of the floor is not damaged, the floor has been in a humid environment for a long time, and the moisture may still enter the floor after the balance layer is eroded by moisture, causing damage to the floor.

3. In order to make the floor last longer, we should pay attention to the maintenance of the floor. If the bulging phenomenon caused by water ingress at the ground splicing place (such as: heating running water, large area of water ingress, etc.), it is a problem of improper use and maintenance by users.

The main reason is that the installation was not done well to prevent moisture, although the back of the wooden floor was not damaged, but due to the long-term humid environment, the wooden floor was damaged.

After the floor is installed, the moisture barrier and the balance layer on the back of the floor will be destroyed during the stepping process, and the moisture from the floor will escape and cause the floor to bulge.

In view of the bulging phenomenon, in addition to product quality factors, the indoor ground in daily life can not be flooded in a large area, and the windows should be closed at any time when the rainy season comes, so as to avoid being wet by rain; When cleaning, try to use a vacuum cleaner or semi-dry mop to take care of it, and do not use a dripping mop to mop the floor

The bulging wooden floor at home may be caused by running water at home, floor heating leakage, soaking the floor, and being damp.

Analysis of the causes of wood floor bulging: 1. The wood floor is mainly caused by uneven floors or sand particles on the flat ground, such as not cleaning the ground before installing the wooden floor, and the presence of some small sand particles will cause the floor to be packed. Or because people are stepping on it, the moisture-proof film and the back of the floor are damaged, and the moisture air can also cause the wooden floor to rise.

2. The wood floor bulge is directly related to the improper handling of moisture-proof measures, mainly because the moisture-proof work is not done during installation, although the back of the wood floor is not damaged, but due to the long-term humid environment, the wood floor is damaged.

3. Improper use will also lead to bulging of the wooden floor, such as water ingress in the joints of the floor, or because of the large area of water ingress will cause bulging.

The house is too damp, is it a wooden floor on the concrete floor?

1. When the wooden floor is bulging, the arching wooden floor and the surrounding wooden floor can be removed, and the arching phenomenon can be alleviated after a period of ventilation.

2. The gap between the bulges on the wooden floor is blocked, resulting in bubbles on the floor.

3. Clean up the contents of the expansion joints of the bulging wooden floor.

4. If the bubble area of the wood floor bulge is very small (the diameter is about less than 2cm).

5. You can directly polish and repair the position of the wood floor bulge (this method is more suitable for parquet).

6. If it is a laminate floor, the bulging wooden floor should be removed.

7. Then use cement to dry the ground, and then replace it with a new floor.

1. The moisture content is unqualified.

According to the requirements of the industry, the equalization rate of sports wood flooring should be between 6% and 14%. However, some sports wood flooring manufacturers are not strict, so that the sports wood flooring products that do not meet the standards leave the factory, and when they are paved to the stadiums, there will be deformation problems.

2. The installation conditions are not up to standard.

Before installing the sports wood flooring panels, the paved raw floors were not thoroughly cleaned, and there were sand or other small particles of debris that arched the panels. Before the installation of sports wood flooring, it is necessary to ensure that other construction projects of the venue are completed, and there will be no rain leakage and water running.

3. There are no moisture-proof measures for installation.

During the installation of sports wood flooring, there are no reserved expansion joints or ventilated baseboards. As a result, the air under the floor is not circulated, and the moisture on the ground is not volatilized in time, which is the increase in the moisture content of the wooden keel or the wool floor.

4. The maintenance is not waterproof.

In daily use, the stadium is not regularly ventilated, resulting in the increase of indoor air humidity, the increase of the moisture content of the wooden floor, and the swelling and bulging of the sports wooden floor.

Check whether the distance between the expansion joints around the wall of your floor is appropriate, and the composite board should leave left and right gaps around the wall, and if the room is large, the length and width should be more than one meter

How to deal with wood floor bulges:

According to the surface inspection specifications during the warranty period of wood flooring, if the diameter of the bulge is less than or equal to 2 cm, if it is laminate flooring, it should be replaced; If it is a parquet floor, it should be sanded and repaired on the original board to be as close as possible to the original flooring color.

If it is within the warranty period, the consumer can contact the supplier directly for a replacement. However, when it comes to replacement, many dealers may pry the bulging floor out and install the new board in the bulging area. Since it is difficult to bond well between the new board and the old board, this replacement method is generally not recommended.

If the bulging floor is in the middle of the house, the correct way to replace it should be to disassemble the floor from the opposite wall, replace the bulging floor, and then gradually pave it. However, it is advisable to place the old floor next to the wall to the bulging floor and the new board next to it. This prevents the new slab from arching.

Wooden flooring is a common problem, which can be caused by temperature changes, humidity changes, aging floors, foundation problems, etc. When it is found that the wooden floor is warped, we should take timely measures to deal with it, so as not to affect the appearance and use.

First of all, it is necessary to stop the hole in time to check the place where the package is cheating. If it is caused by gravity or a leaking sewer pipe, then the problem must be identified and fixed to prevent the problem from progressing.

Secondly, the following measures can be taken to deal with the problem of wood floor packing:

1.Reduce the load: According to the position of the wooden floor, remove the weight on it, reduce the weight of the wooden floor, and make the wooden floor recover naturally.

2.Cutting: If the warp is too large, you can solve the problem by cutting the concave part, of course, you need a professional to operate.

3.Clamp with a clamp: You can add clips at both ends of the bending place of the wooden board to bend the wooden board into a normal shape, and let it stand for 14-28 days to rent the weighing cover. This method can be used for small area wrapping.

4.Dismantling and resurging: For large areas of damp flooring, remove the plank, clean the floor, and then resurface the floor. Batch scraping can be used to form a moisture-repellent barrier before laying. Although this method is time-consuming and labor-intensive, it is the most effective and long-lasting.

5.Use professional repair tools: Professional floor repair tools can help repair warped wooden floors and prevent future problems. You can consult a professional floor repair company to choose the right method and use safe and reliable repair tools for repair.

Finally, it is necessary to maintain the wooden floor regularly to prevent the occurrence of wooden floor wrapping or other problems. The cleaning, maintenance and maintenance of the wooden floor have become an important link, and regular waxing and moisture-proof work can greatly prevent the problem of wooden flooring.

1.The base layer is not well treated, causing the wooden floor to bulge: the ground is uneven or there are sand particles on the ground, so that the wooden floor is not cleaned before installation, so that there are some small sand particles on the ground or the ground becomes relatively rough, after the floor is installed, people in the process of stepping on it, the moisture-proof film and the balance layer on the back of the floor will be destroyed, and the moisture of the ground will cause the floor to bulge.

2.Improper handling of moisture-proof measures in daily life causes the wooden floor to bulge: this kind of situation belongs to improper moisture-proof treatment during installation.

If the moisture-proof membrane joints of the damp floor are not tightly glued with waterproof tape, although the balance layer on the back of the floor is not damaged, the floor has been in a humid environment for a long time, and the moisture may still enter the floor after the balance layer is eroded by moisture, causing damage to the floor. Improper use, due to the bulging phenomenon caused by water ingress at the floor joint, belongs to the improper use and maintenance of the user.

3.When paving the floor, there is no reserved gap to cause bulging: the floor ignores the principle of thermal expansion and cold contraction in the process of paving, and expands after being exposed to moisture in the use of the floor, because there is no gap reserved in advance, which causes the surface of the floor to bulge.