How do I keep my meter from leaving? How to keep the meter from leaving

There are the following ways to keep the meter from leaving:

1. If you can move the meter, open the meter wiring cover, put the first foot of the meter and the second foot with a metal connecting piece, unscrew it, as long as it can't be touched, the meter will stop, if you want it to turn, tighten it.

2. In the first foot (live wire inlet) and the third foot (live wire out), connected with a copper wire, the meter will rotate slower, if it is a large meter, a month with 5-6 degrees, may only turn about 6 degrees.

Abstract Hello! There are the following ways to keep the meter from going: if you can move the meter, open the meter wiring cover, put the first foot of the meter and the second foot with a metal connecting piece, and loosen it, as long as it can't be touched, the meter will stop, and if you want it to turn, tighten it.

The second method, in the first pin (live wire incoming) and the third pin (live wire outgoing), connected with a copper wire, the meter will rotate slowly, if it is a large meter, a month with 5-600 degrees, may only turn about 60 degrees.

How do I keep my meter from leaving?

Hello! There are the following ways to keep the meter from going: if you can move the meter, open the meter wiring cover, put the first foot of the meter and the second foot with a metal connecting piece, and loosen it, as long as it can't be touched, the meter will stop, and if you want it to turn, tighten it.

The second method, in the first pin (live wire incoming) and the third pin (live wire outgoing), connected with a copper wire, the meter will rotate slowly, if it is a large meter, a month with 5-600 degrees, may only turn about 60 degrees.

It's so simple, one uses a magnet to put it on the meter, but look at the N pole and the S pole The other is that the two wires pass through the meter and output to the knife, and the other does not go through the meter to the knife, so it will go, but there are very few points. It will also be slow to use an induction cooker. Hope it helps.

You can't go by just plugging in one line. Only when the meter is connected to a live line and a neutral line can a protection mechanism be formed, and the meter can work on a journey; If you only connect one live wire, the meter will not work.

Energy Meter:The electric energy meter is a meter used to measure electrical energy, also known as the watt-hour meter, fire meter, and kilowatt-hour meter, which refers to the instrument for measuring various electrical quantities. When using an energy meter, it should be noted that in the case of low voltage (no more than 500 volts) and small current (tens of amps), the energy meter can be directly connected to the circuit for measurement.

In the case of high voltage or high current, the energy meter cannot be directly connected to the line, and needs to be used with a voltage transformer or a current transformer.

Answer: After the general meter is calibrated, the shell will be sealed by the calibration personnel, and labeled, indicating the verification date and validity period.

If you move the lead seal and remove the meter cover, even if it is out of good intentions, and then the relevant personnel suspect that you have manipulated the meter and caused it to not work properly, then you really have a hard time arguing.

Therefore, it is recommended that you report to the landlord or the electricity supply department and ask them to deal with it.

Pull off the switch, and don't use any electricity.

Is it electronic or analog?

Stealing electricity is an illegal act, and you can't ask about it, let alone do it. Now the city has basically replaced the electronic meter, the sensitivity is higher than the old mechanical meter, it is impossible to find a master who understands electricity like the old watch, you can pay less electricity.

The staff who charge are not stupid, and they will come to you to find out the reason for the sudden fluctuation of your electricity consumption. Remember not to do these things, if you want to use cheap electricity, you can go to the mountains where there are small power stations to build factories, small power stations are cheap electricity is not illegal.

Meter considerations.

The starting current of the meter is about the rated current when the power factor is 1, so a 10A meter will only start to rotate when the current passes through, and its power is equivalent to 12 24 watts on a 220V line.

Although the meter is a precision instrument, there is still unavoidable mechanical resistance when it is rotated. At the beginning of the rotation, the accuracy of the meter is not high because the prime mover torque is not much different from the mechanical resistance.

The meters are sealed and cannot be opened, but it would be easy if they could be opened. The easiest way to keep the meter from turning is to loosen one end of the transverse connector next to the meter inlet line, then break it to the side, and then tighten the screws.

The wiring does not move, but the electricity does not go to the meter. Another way, which is more complicated but more hidden, is to use a magnetic field to make the watch go slowly or not. If it's an electronic meter, you have to use a jammer, it's complicated, you won't.

Besides, why do you want the meter not to go? Just look at the title and you'll know what you're going to do. Don't do bad things!

I'll tell you if these are the "sin of teaching others how to sin"? Hey.

2.It doesn't matter if it's single-phase, two-phase or three-phase, the principle is the same, they flow through the meter like a stream of water, and the meter records the amount of flow like a counter. How to make the number less is to reduce the amount of electricity flowing through the meter.

3.The meter is actually an electrical appliance, as long as we short-circuit it with a wire, then the current flowing through the meter will be less or nothing, and this is our method. The meter will have a live wire connection inlet and a neutral wire connection inlet, as well as a live wire outlet and a neutral wire outlet, we only need to connect a copper wire between the two live wires, so that the meter will be.

How many ways are there?

1. Do not use the neutral line of the meter.

2 There is also an electricity meter is in... Go out? You can improve. Go out?

3. When the lid of the meter is opened, there is a small iron piece connected to remove it?

Answer pro! Hello, in fact, it can be done to slow it down, but it is illegal to steal electricity, technically speaking, you can use a coil and an adjustable frequency conversion high-power driver, use the coil to interfere with the meter, adjust the frequency and intensity of the driver under the same meter power load, and carefully observe the changes in the meter.

1. If you can move the meter, open the meter wiring cover, put the first foot of the meter and the second foot with a metal connecting piece, unscrew it, as long as it can't be touched, the meter will stop, and if you want it to turn, tighten it.

2 The second method, in the first foot (live wire incoming) and the third foot (live wire out), connected with a copper wire, the meter will rotate slowly, if it is a large meter, a month with 5-600 degrees, may only turn about 60 degrees.

Here's a reminder to stay safe!

The method of keeping the meter from going away and having electricity is as follows:

If you want to keep the meter from going, but can keep the electricity, you can reconnect the wires in the meter, there are yellow wires in the meter, and we can connect the yellow wires with the yellow wires, and connect the blue wires with the blue wires, so that the meter will not be electrified, but it can be used normally.

But in fact, this kind of behavior is definitely not good, because in essence, we are stealing electricity, and once we are caught by the relevant departments, we will be fined.

Rules for the use of ammeters:

The ammeter should be connected in series in the circuit (otherwise it will be short-circuited. ）；

The current to be from"+"The binding post enters, from"-"The binding post is out (otherwise the pointer is reversed.) ）；

The measured current should not exceed the range of the ammeter (you can use the method of test chain monitoring to see if the range is exceeded.) ）；

It is absolutely not allowed to connect the ammeter to the two poles of the power supply without passing through the electrical appliances (the internal resistance of the ammeter is very small, equivalent to a wire, if the ammeter is connected to the two poles of the power supply, the pointer will be crooked, and the ammeter, power supply, and wire will be burned out. ）。

In China, the voltage of the power supply line of the family house is 220V, the frequency is 50Hz, and the rated voltage and applicable frequency of the selected electric energy meter should be consistent with the voltage and frequency of this line, and it should also be 220V, 50Hz. <>