How can you make the meter go slowly? How can I make the meter go slower?

There is a screw on the left side of the shell of the table, which is 1cm in diameter, which is used to calibrate the watch, and can be turned clockwise with a flat mouth, it will go slowly, but the slowest can only be less than about one degree of electricity a day, if you want to only go ten kilowatt-hours a month or less, you have to use the second method to steal the beam and change the column, take a 600 rpm meter, that is, turn 600 times to one kilowatt-hour of electricity, the larger the number means that the same electricity will be turned more times, remove the gear combination inside, Change it with the gear combination of your big meter, your big meter must be the kind of 200 rpm, after replacing it, haha, your electricity bill is the original 1 3, rest assured, the parts in the meter are standard parts, it must be worthy of it, but it is to completely remove the meter when doing hands and feet, it is more troublesome, once it is replaced, it is the person from the meter factory who will not find the reason to check, unless he takes the meter back to the tester to measure the number of revolutions, the general electricity bureau does not have this equipment, haha.

The above method is a bit troublesome, the last plan, is to stop the table completely, this method is easier to implement, notice that there is a rectangular cover at the bottom of the table, remove the only screw on the top, there are a few screws on the left inside, two of them are connected with a small horizontal connecting strip, loosen the two screws, dial the connecting strip to the other side, cover the lid, okay, see if the meter is still gone, it is recommended to walk on ten kilowatt-hours of electricity every month and then do this, Otherwise, you can't use 0 kWh of electricity in a month.

According to your description, this is an act of electricity theft.

Electricity theft is illegal, and no individual or organization may use any means to commit electricity theft.

According to the relevant laws and regulations of China, the power supply enterprises will stop the electricity thieves and can stop the power supply on the spot. The person who steals electricity shall pay the electricity fee according to the amount stolen, and bear the default electricity fee of three times the electricity fee. If the power supply company refuses to bear the responsibility for electricity theft, it will report to the power management department to deal with it in accordance with the law.

If the amount of electricity stolen is relatively large or the circumstances are serious, the power supply enterprise will request the judicial authorities to investigate criminal responsibility in accordance with the law.

We hope you find ours helpful.

Turn off the lights and use less electricity or pull the brake directly.

Private individuals cannot slow down the meter.

Method 1: The professional instrument [electric energy meter effect inspection device] is used to calibrate the meter, so that the electronic meter can be slowed down.

Method 2: Modify the pulse constant in the metering program.

Method 3: After disassembling the meter, a copper wire is added to the sampling shunt. Steps: 1. Tilt the vertically installed meter by 15°.

2. Open the meter wiring cover, loosen one of the screws of the current wiring card at the top left of the terminal (horizontal clip), (note that there is electricity, please use an insulated screwdriver to operate), the meter at this time is counted when the electricity load is large, and the load hour is not counted. 3. If you are a little more professional, you can open the meter shell and loosen the top wire above or below the center of the rotating disk, which is the best way to use this method with the first method.

An electricity meter is a device manufactured in accordance with national regulations to measure electricity consumption. Under normal circumstances, the normal meter will fairly measure the amount of electricity consumption according to the set parameters. But in some cases, the meter will go faster than normal, is there any way to make the meter go a little slower?

Here's how to do it, but it's highly recommended that you don't try it!

Turn on step-by-step reading mode.

Tool materials: meters, magnets, wires.

How it works: The structure of the meter.

The watt-hour meter is mainly composed of two parts: the measuring mechanism and the driving element. The measuring mechanism is the core part of the electrical energy measurement, which consists of a turntable, a rotating shaft, a brake magnet, a gear and a meter. The drive element is composed of a voltage coil and a current coil, which is used to convert the alternating voltage and current into alternating magnetic flux.

How the meter works.

The watt-hour meter uses the principle of electromagnetic induction, which rotates the aluminum disk through the eddy current generated by the voltage and current coils on the aluminum disk; The alternating magnetic flux interaction generates an electromagnetic force as a braking torque, which makes the speed of the aluminum disc proportional to the load power, so that the meter calculates the amount of electricity.

According to the principle of the watt-hour meter, it can be known that changing the speed of the watt-hour meter, the gear conversion ratio, and changing the current, voltage, and phase of the input watt-hour meter can achieve the purpose of making the meter go slower.

The easiest way to do this is to place a large magnet with a strong magnetic force on the pointer of the meter, which can change its rotational speed and make the pointer go slower.

The most effective way is to connect the live wire at the input end of the meter to the live wire at the output end with a wire, so that the meter will be short-circuited, and the meter will basically not go. But this method is extremely dangerous, so don't try it!

Dear, this is an unrealistic question.

If you use less electricity, you will have less meters.

Just go slower.

Ask a question, then you solve that fart.

Tricked me out of three bucks.

You're kind of funny.

Is it OK to ask questions that a normal person can ask?

Questions**. And let the meter go slower Why don't you ask to make time go slower?

It's hilarious. Asking questions is to make it slow down, I can't communicate, but the speed specification of the meter is stipulated by the state How much you use is how much you go If you modify its speed without authorization It is illegal This is already called stealing electricity [tear run] [tear run] ask a question.

I don't think it's practical to make the meter go slower, because this meter has been tested by a regular country, and it has a metering range, so it can't be slow.

Let the meter go slower, then you can only reduce the electricity consumption, and try not to use those high-power appliances, so that it will be more energy-saving!

If you want the meter to go slower, then when you don't use electricity or you need to turn on two lights at home, and you only turn on one, then won't its meter go slowly?

How can you make the meter go slower? This is inherently wrong. The country's electricity meter will. Carry out the effect before installation. That is, to align the table to the level of standard. to be able to put it on.

The same room, thinking about things upstairs more than 100 degrees, we stood to more than 1600, always said, we use a clock, he is upstairs, I am downstairs.