How noisy is the Qianfeng gas water heater after maintenance?

Today, we will introduce to you in detail the handling of the flameout problem:

The maintenance method of the forward water heater service personnel: after turning on the faucet, use your fingers to pull on the micro switch, and the angle is larger, which is equivalent to holding the water diaphragm hard and opening the air valve, so as to hold on to see if the fire can be played. If the fire can be played and not extinguished, then the water diaphragm is not good, and the water diaphragm in the water-gas linkage valve is hardened, and the fire can be ignited when the water is just boiling, but it will be extinguished immediately.

This is not a big problem, just change one piece, in addition to this reason, there are the following points that will also cause the water heater to go out.

The solenoid valve is broken, can not work normally, can not be sucked, and the air is not ventilated.

The ignition's induction needle is too dirty and the induction is not good. You wipe the sensor needle clean and try again. Otherwise, there is a problem with the ignition control.

3. It is likely that the water pressure is not enough, you can try to reduce the flow of the water, so that the water pressure rises. When the water temperature is high, you can adjust the air volume appropriately.

4. The extinguishing after ignition is because the air pipe is too small or you let the exhaust pipe expel the exhaust as soon as possible.

Mianyang Qianfeng Water Heater Maintenance Center recommends you: If you don't understand more maintenance knowledge at all, the center recommends that you still don't move by yourself. Please call Mianyang Qianfeng water heater maintenance in time**Gas water heater involves both water and gas paths, and it is not possible without professional tools.

If you are not careful, it will be charged by high-voltage electricity, and there may be serious accidents such as air leakage. For the safety of yourself and your family, please do not disassemble the gas water heater without permission. If the water heater fails, please call our 24-hour free ** consultation and repair in time.

<> gas water heater during the maintenance process, some problems may occur that cause noise. Here are a few causes that may cause noise after gas water heater repair and the corresponding solutions::

The installation of the gas water heater is not firm or the pipe is loose: check whether the gas water heater is installed on a stable surface, and at the same time check whether the gas pipe and hot water pipe are firmly fixed, and adjust the loose parts in time.

Insufficient gas combustion or improper adjustment of the valve: Check whether the gas valve is properly adjusted and whether the gas combustion is sufficient, if it is not sufficient, clean the combustion chamber or adjust the gas valve.

Loose or worn internal components: Check for loose or worn internal components, if a problem is found, it needs to be disassembled for repair or replacement.

Blocked pipes or stagnant water: Check the pipes for blockages or stagnant water, and remove debris from the pipes.

If the above methods cannot solve the problem, it is recommended to contact the manufacturer or professional maintenance personnel for inspection and repair. At the same time, please pay attention to the safe operation specifications when using gas water heaters to ensure the normal operation of gas water heaters.

There are several reasons: 1. The problem of the fire power of the water heater. 2. Water pressure problem of water heater.

3. Sometimes it is because of the problem of the fan. In addition, some gas water heaters have a cleaning safety function, which will remove the leaking gas to avoid deflagration, you can turn off the water heater first, and if there is still a noise, you should pay attention to it to prevent accidents. Suggested Treatment:

1. Adjust the firepower. First of all, you can turn down the heat a little first, generally there will be a rotating lid on the gas meter, counterclockwise rotation can make the fire smaller, and then check if there is a buzzing sound, if there is, it means that it is a fire problem, and when using a water heater, it is not recommended to turn the fire too large. 2. Reduce the water pressure.

You can close the water valve first, and then see if the water heater is still ringing, under normal circumstances, after the water pressure reaches balance, the water heater will not make a sound, and when the water pressure is relatively large, the water heater will not be balanced, and there will be a trembling situation, at this time there will be a buzzing sound, so it is best to install a one-way valve at the position of the water inlet of the water heater. 3. Check the fan. The last thing you need to do is to check if there is a problem with the fan, but this often requires opening the water heater to see its internal structure, so it is not recommended to check it alone at home, and you should ask a professional to check it.

And when buying a gas water heater, be sure to choose a good brand and have a professional install it.

1. Check the contact object of the smoke exhaust pipe of the water heater to see if there is looseness or air leakage. Generally, if there is, or if it comes into contact with pine animals, it will cause resonance. 2. Check the heating rod inside the water heater, it may be caused by too much scale on the heating rod.

3. It is also possible that during installation, the master did not stick the water heater to the wall, which easily caused a gap behind the water heater, resulting in resonance caused by the operation of the water heater. 4. The sound produced by the smoke exhaust pipe gasping into the air. 5. Caused by excessive scale in hydrostatic felling.

Suggested workaround:

1. If the smoke exhaust pipe is loose, you can replace it with a new pipe.

2. Replace it with a new heating rod bridge.

3. If the town is not installed properly, then you need to find a master to reinstall it.

4. Find a rubber pad and stuff it into the royal regret, or re-tighten it with screws. 5. The smoke exhaust pipe is generally installed outward, if the mouth of the smoke exhaust pipe is warped outward, then it is easy to pour air into it, causing noise. Just pull the jar low.

6. The water heater is always chirping, which is the sound of water flowing, because there is a water pressure in it, and after the leather bowl is used for a long time, it produces scale, so this sound is produced. Generally, there will be no danger, for safety, it is recommended to contact professional after-sales personnel for replacement.

1. If the water heater keeps making sounds, it should be the sound of water flowing, because there is a pressure valve inside. After a long period of use, limescale will form, so this roaring sound will occur. 2. Generally, there will be no danger in this situation, for the sake of safety, it is recommended to contact the relevant after-sales service personnel for door-to-door replacement.

Suggested solutions: 1. Check whether the smoke exhaust pipe of the Qianfeng water heater is in contact with the Soho object to see if it is loose or broken, and if the air leaks, it will resonate with other objects and make a sound. 2. Check the heating rod inside the water heater, if the heating rod is used for too long and there is no regular warranty, too much scale will cause the water heater to make a roaring sound, you should find a professional to clean the water heater.

3. It is possible that when the water heater is installed, the installer does not stick the water heater to the wall, and a large gap will be created in the middle, which will cause the water heater to resonate with the wall when it is working. You can find a rubber pad to plug in it or use screws.

Tighten it on. 4. The smoke exhaust pipe is generally installed outward, and if there is a nozzle of the smoke exhaust pipe, Shizhi Laozi faces outward. And if it collapses and warped, it is easy to pour air into it. If there is a strong windy weather, it will produce a very strong sound, and it is enough to pull the tube down a little.

Summary. Dear, I changed the water heater and the gas soared loudly as follows:1

First of all, no matter which situation makes a sound, you must contact the official after-sales service of the water heater, and do not repair it by yourself, so as not to cause more serious damage to the electric water heater, etc., and the damage caused by self-repair is not covered by the warranty. 2.If the sound is caused by excessive water pressure, simply install a pressure reducing valve on the outlet pipe.

If the water is blocked due to limescale problems, do not systematically drain the water pipes, and clean the water tank to ensure that the water quality is clean in turn.

Dear, I changed the water heater and the gas soared loudly as follows:1First of all, no matter what kind of situation makes a sound, you must contact the official after-sales service of the water heater, do not repair it by yourself, so as not to cause thrilling accidents, and the damage caused by self-repair is not covered by the warranty.

2.If the sound is caused by excessive water pressure, simply install a pressure reducing valve on the outlet pipe. If the water is blocked due to limescale problems, do not systematically drain the water pipe, but also clean the water tank to ensure that the water quality is clean and vibrating in turn.

The reason is that the smoke exhaust is not smooth, which is easy to lead to the resonance of the machine, and the grip can dredge the smoke exhaust pipe to solve this fault. If the screws are loose, try to strengthen the leak with a tool. It is in disrepair, there is no maintenance for a long time, and the work efficiency is reduced.

Regular maintenance is the only way to make your water heater last longer. The occurrence of backfire will also make the gas water heater noisy. If the motor is used for a long time, the deformation or rust of the fan blades will make the noise of the gas hot water heater become particularly loud, and the damaged parts need to be replaced in time.

Among them, air supply, combustion and exhaust air are the three most noisy causes. It can be seen that the gas water heater is a machine that burns in a sealed pipe, and in order to ensure that the flame can be continuously generated, the fan needs to be forced to supply air, and the exhaust gas after combustion must be discharged. In this process of entering and exiting, the mixture has complex eddy currents and pressure fluctuations, which are the source of noise.

The main reasons for the noise: 1. The smoke exhaust is not smooth, which is easy to lead to the resonance of the machine, and the smoke exhaust pipe can be dredged to solve the fault. 2. If the screws are loose, try to strengthen them with your own tools.

3. It is in disrepair, there is no maintenance for a long time, and the work efficiency is reduced. Regular maintenance is the only way to make your water heater last longer. 4. The phenomenon of backfire will also make the gas water heater noisy.

5. If the motor is used for a long time, the deformation or rust of the fan blades will make the noise of the gas water heater very loud, and the damaged parts need to be replaced in time. 6. If there is too much air, adjust the air intake switch appropriately. 7. The gas joins hands with the controller of the water heater, and there is a problem with his ignition system, so that the frequency of the electric shock is not fast enough, and the electric shock is not enough to reach the normal situation, so that the gas gathers inside and deflagrates when encountering an open flame.