How do I cancel F2F1 when I turn it on on my computer

BIOS to set it up.

This is a problem with the boot setting of the boot item, set it to hard disk boot, the operation steps are as follows:

1. Press "F2" or "Delete" to enter the BIOS interface of the computer, and find the first "Standard CMOS" press enter to enter.

2. Then enter the Standard CMOS interface, find "floppy A" and press enter to select the mode.

3. Select the first line "disabled", press enter on the keyboard to change the settings, and press "F10" to save the settings.

4. Press "Ctrl+Alt+Delete" to restart the computer to boot normally.

Every time the computer is turned on, it will prompt you to press F1 F2 How to cancel it?

Every time the computer is turned on, it will prompt you to press F1 F2 How to cancel it? Hello dear, 1. Set the hard disk to boot under the delete" to enter the BIOS interface of the computer and find the first one"standardcmos"Enter to enter. 2. Then enter the Standard CMOS interface, find "floppy A" and press enter to select the mode.

3. Select the first line "disabled", press enter on the keyboard to change the settings, and press "F10" to save the settings. 4. Press"ctrl+alt+delete"Restart your computer and it will turn on normally. I hope mine can help you.

If my answer is helpful to you, please give a thumbs up (in the lower left corner), I look forward to your like, your efforts are very important to me, and your support is also the motivation for my progress. Finally, I wish you good health and a good mood!

Pressing F1 will enter the BIOS settings, and pressing F2 will enter the system from the default settings. At this time, the system time will be the time when the BIOS was initially created, which does not correspond to the real-time time.

Due to the large number of BIOS versions, different settings can cause different ways of error, but there are a few basic cases:

1. Motherboard battery.

Failure, the battery can be replaced;

2. Turn on the floppy drive, you can turn it off in the BIOS;

3. If the power supply circuit of the motherboard fails, it can be sent to the after-sales service;

4. If the CMOS data is changed due to a virus attack on the CMOS, it can be checked and disinfected.

Of course, the latter two scenarios are very unlikely. If it's the first case, you can buy a simple coin cell battery.

to solve. In the second case, the procedure is as follows: (Take Dell computers as an example).

Power on"del"button to enter the CMOS settings.

main settings interface - > legacy

diskette

The value of item a is changed from [selection to none (some versions can be disable)—press f10 to save and exit—> restart your computer. (If the BIOS is a different version, you can find Legacy.)

diskette

a, just modify it directly! )

The reason for this phenomenon is because of the diskette

A reserves boot space for floppy drive startup, although there is a floppy drive mode in the startup item, but in fact, the current computer does not need to use the floppy drive, so this hardware setting does not correspond to cause the computer to detect errors.

It is estimated that the motherboard battery is dead, change it, and then go into the BIOS to update the date and time.

appears when the computer is turned on"f1"with"f2"The problem is because the motherboard has detected some configuration issues or setup errors. F1 and F2 refer to the "Major Default Settings" and "Chipset Default Settings" in the BIOS, respectively, and you can fix this by following these steps:

1.Press F1 or F2. When the computer is turned on, quickly press the F1 or F2 key to enter the BIOS settings.

2.Restore the default settings. Once you're in the BIOS settings, select "Load Optimized Defaults" or "Load Setup Defaults", then press Enter to restore the default settings, then save and restart your computer.

3.Check the hardware. If the problem still cannot be solved according to the above methods, it may be a hardware problem, such as memory, hard disk or motherboard, etc., it is recommended to go to a professional computer repair center for repair and maintenance.

These measures are relatively simple, but they need to be done with caution to avoid other problems or mistakes. If you are unsure of how to operate or if you have other problems, it is recommended to contact your computer manufacturer or after-sales service center for consultation and assistance.

If F1 or F2 occurs when the computer is turned on, it is usually caused by an error found during the computer boot self-test.

Generally, there are several situations: 1. The CPU fan is wrong (the cable is not plugged in or the fan is faulty). 2. Motherboard battery.

Insufficient voltage. (This is more common). and some other errors, which require the user's confirmation before proceeding.

Solution: Plug in the CPU fan power cable, or replace the fan, and then replace the motherboard battery.

If you don't find any problems after troubleshooting and don't want to press F1 or F2 every time you turn on the computer, you can turn off the function of pressing F2 for the error message in the BIOS.

You can refer to the specific operation method, thank you!