What parts are related to the strength of the car

The vehicle is full of power, mainly related to the engine, gearbox, and various transmission parts, air intake and exhaust

Hello, the strength of the car engine has a lot to do with the engine, gasoline quality, and gearbox, not a problem on the one hand!

Hello the power of the car, comes from the engine, and the computer version, these things. and the speed at which the gearbox outputs.

The driving power of the car is mainly related to the engine displacement, power, torque and transmission tuning.

Engine, must it? The more powerful the engine, the better the technology, the greater the torque, so the vehicle has strength.

The maximum power determines the optimal speed of the car.

The maximum torque determines the car's ability to accelerate.

Of course, the maximum torque corresponds to the engine speed, which also has a relationship. In addition, the logic of the gearbox and the speed of shifting have a great impact on the driving experience.

Hello, whether the car is driving vigorously is related to the engine output, horsepower, car displacement, etc.

Hello, the power of the car mainly depends on the engine and gearbox, the engine power should be sufficient, and the gearbox should be well matched.

If there is, it also has a lot to do with the engine, and in general, you have to look at its horsepower and power.

Whether the motor vehicle has strength depends on the engine, the maximum power output, horsepower, and the same displacement also has a lot to do with the manufacturer's tuning.

Hello, if the car is driving vigorously or not, it mainly depends on the displacement of the car, and then whether there is carbon deposit in the engine.

Hello, this mainly depends on whether the engine combustion charge is 100 and the ignition oil supply and cylinder pressure are related.

Whether this motor vehicle engine is beneficial or not, the key still depends on your engine displacement, as well as the maximum power of the engine and the maximum horsepower of the engine, these parameters.

Whether this motor vehicle has a strong road, the key depends on the salary, maximum power, horsepower, and its displacement has a lot to do.

I think the car starting acceleration performance and the design details of the engine part is very related, the greater the speed of the engine twist, then the more powerful the car starting acceleration performance, and the clutch, automatic design details of these parts are particularly related, because the car is a very large power system, involving the whole body, can be used to describe the car starting acceleration performance.

I think it is related to the design details of the parts and components of the car that are suitable for the starting acceleration performance of the engine, because the power of your engine, if it is sufficient, then it has a very fast speed, so this time is to test the speed of your engine.

I think the thing that has to do with these parts and these details is the powertrain plus the driving structure and the driver. Although the structure of the car and the accessories are very important, I think the most important thing is the skill of the driver. Because no matter how good the car is, if it is handed over to a person who does not know how to drive, she is also a pile of scrap metal, and no matter how bad the car is, it can be handed over to a person with excellent driving skills, he can also give you the feeling of driving a sports car.

I think the starting acceleration performance is suitable, the total power bonus, and then it is related to the design details of some parts such as the driving mechanism, because such details affect what kind of compression resistance your car has, and what kind of starting speed your car can use.

Generally speaking, the greater the maximum torque of the engine at the same weight, the better the acceleration performance of the car. And with the same engine torque, the smaller the weight, the better the acceleration. The torque of the engine varies with the change in speed.

Therefore, the maximum torque of the car is often marked at the same time as the speed.

In fact, I think there is a certain relationship between the performance of the car's starting acceleration and the engine, because the larger the displacement of the engine, the faster it accelerates. In fact, in life, why are those cars with large displacement expensive? Because it consumes a lot of fuel, and the other is that it accelerates quickly and will be smoother on the road, so these details are related to the design of its engine.

The car starting acceleration performance is related to the design details of the powertrain and driving mechanism, and the acceleration performance of the car is a test to measure the effective acceleration of a car, and the size of some tires and the speed of gear change are inseparable from the starting acceleration performance of the car.

The acceleration performance of the car starts, first of all, the first is to the displacement of the car and its torque, the second is the quality of the car tires, of course, the size of the wheels is related to the size of the wheels, the larger the wheel, of course, it must be better, but its performance will be deeply affected, in addition, the size of the wheel hub and the matching of the tires also have a certain relationship, if it is said that because of the mismatch, it will still reduce its torque, and the acceleration performance is slower, such as a Mercedes-Benz A45 series car, after the modification of 01 can run to 2

It is related to horsepower, torque, drive mode, tires, vehicle weight, and transmission mechanism. Horsepower determines speed, torque determines acceleration, front-wheel drive is the slowest, four-wheel drive and rear-wheel drive are difficult to say, when too much horsepower, I feel that four-wheel drive starts better, tires determine grip, torque is enough to grip the start is better, the car is light and fast, and the transmission mechanism transmission efficiency is high.

The 05 years of Beverly are a bit old, and from the fault phenomenon you provided, you can see 3 possible problems, if you plan to change the nozzle and high-voltage wire, I can tell you clearly, there is no effect.

1. The standard idle speed of Beverly is 700 rpm plus or minus 50 rpm to normal idle speed (except for cold cars), the idle speed is too high and needs to be adjusted, and check for problems, such as idle motor hairpin, air intake manifold leakage, and water temperature sensor damage.

Second, the time of refueling is normal and sometimes abnormal; It is necessary to check whether the gasoline grid is dirty, and the fuel rail pressure is insufficient due to refueling, and it is also necessary to check whether the gasoline pressure is sufficient (gasoline pump), if the gasoline pump is seriously worn, the nozzle filter is dirty, and this fault will also occur.

3. Check whether there is leakage in the ignition system, such as leakage of high-voltage lines, poor contacts of distributors, insufficient high-voltage ignition energy, blocked inlet air filters, and blocked exhaust pipes will cause you to refuel poorly.

Fourth, check whether the cylinder pressure is sufficient.

These checks will solve the problem.

Changing the spark plug and high-voltage wire, of course, can't be improved.

I don't know if you're EFI. If it is EFI, one: it is recommended to adjust the ignition time of the distributor and clean the electronic injection head. Check the valve clearance.

If you are a carburetor, two: it is recommended to replace the carburetor (it is time to change it after a 6-year-old car), adjust the ignition time, and check the valve clearance!

The above must be established under the condition that the valve mechanism and crank connecting rod mechanism are normal!

It is advisable to find a repair shop on the side of the road and have them measure the cylinder pressure gauge. In the case of normal cylinder pressure, it is ruled out that there is a problem with the valve mechanism and the crank connecting rod mechanism, and check one or two of the above!

The spark plug depends on the situation, it is replaced when it is aged, and it doesn't matter if you use the momentum normally, you can try to clean the lower grease nipple and check the compression pressure of the engine. The clutch plate burned, changed the clutch three-piece set, and that's it!

There is one way you can try it, that is? By the way, the premise is that your handbrake should be easy to use, pull the handbrake, gear up, increase the throttle, and easily clutch to see if the car is not turning off, showing signs of skidding!

If! Then this clutch plate is a big problem!

By the way, have you ever tried all four tires that rotate flexibly! If not, you check it on the lift. If you have tried, then you can just use my previous method!

Let's take a look at the clutch!

By the way, you said that the idle speed after the hot car is 1000-1100, which is too high, and the normal idle speed of the hot car is 800 plus or minus 50 rpm without turning on the air conditioner!

1. The idle speed is too high, and the normal idle speed should be between 750 and 850 (per minute) 2. Do not blindly replace accessories. It is recommended that you check it out first. Check the pump pressure to see if you have refueled the ...... of inferior oil at a private gas stationThere are a lot of questions involved, so it is recommended that you go to a special place to check it out before making a plan.

3. The aging of the high-voltage line and the leakage will make the spark plug sometimes jump out of the fire is not a big problem, it is recommended to go to a 4S shop or a large repair shop to get it. It will take about an hour to find out the problem for you.

The idle speed of 1000-1100 is a bit high, and around 900 should be fine.

The high-voltage line should not change much, the spark plug you see the situation, the aging is replaced, it doesn't matter if the momentum is normal, you can try to clean the grease nozzle and the like, I also probably know a little, looking forward to the expert to point out...

You look to see if the intake pressure sensor is broken. Whether the exhaust pipe is a little blocked, whether the ESU is broken, whether the high-pressure bag jumps well, and whether the fuel pump pressure is enough. Is the cylinder pressure enough? . .

The idle speed should be in the 800-900 range

You have this fault, you need to check the fuel system.

Normal idle speed is 850rpm

Forget the important point, the inlet pressure sensor, this sensor has a vacuum tube connected to it, to carefully check for blockage.

The idle speed is normal at 800 rpm in the hot car, and the idle speed is high above 1000, and the power is insufficient; The high-voltage line can be judged, and it is estimated that it is not the main focus of the problem, and it is OK to check the spark plug for platinum.

Focus on checking the three-way catalysis to see if it is blocked.

Clean the throttle head of the intake tract.

Check the compression pressure of the engine, if it is not enough, the engine should be overhauled. Adjust the idle speed.

An idle speed of 750-800 is fine.

See if there's a problem with the throttle.

The maintenance of the car is often more important than the brand. No matter what it is, it is necessary to pay attention to the key to maintenance.

1. Whether refrigeration and air conditioning are used.

2. Driving conditions, the most fuel-efficient at constant speed and economic speed.

3. The heavier the car, the lighter the more fuel-efficient.

4. Electricity consumption, the more electricity consumption, the greater the magnetic resistance of the generator.

5. Driving habits, stepping on the brakes too much will definitely not save fuel.

6. The engine temperature is about 70 degrees Celsius, and the oil viscosity is high and the lubrication is not good when it is too low. When it is too high, the oil adhesion is poor, the lubrication is reduced, and the cooling fan is turned on and the power consumption is consumed.

7. Oil performance.

8. Tire resistance, wide tire resistance is large, and the resistance is also increased when there is air shortage 9. Aerodynamics of car body design.

10.Excessive carbon deposition will make the intake pipe wall rough, affecting the air intake effect and the quality of the mixture, and causing fuel consumption to rise dramatically.

Tires are the most direct, and only tires can be changed.

If the big changes, 1 turbo, normal driving slightly reduces fuel consumption and improves power. 2. Double overhead high-speed camshafts. 3 cast iron connecting rods. 4. Large-caliber intake and exhaust. 5 mushroom heads. ......And so on, a lot.

The engine and transmission also have axles.

The power of the car must be inseparable from the engine of your luck, and the engine is one of the power barriers of the whole car. With it, you can make it easy to make the transmission shift better, and then your speed will go up. All power** is inseparable from the engine.

Depends on the power of the car's engine. Maximum power: determines the maximum speed of the car, and the acceleration ability of the middle and rear sections; The higher the maximum power, the higher the speed, the more power that can be theoretically squeezed.

The greater the maximum power, the higher the theoretical top speed of the car, and the stronger the acceleration ability in the middle and rear sections. Maximum torque: determines the acceleration time of the car; The lower the speed of the peak torque, the earlier the peak torque output curve, and the larger the torque value, the greater the starting acceleration g value, and the better the theoretical climbing and starting performance. Hope.

Car displacement, engine power, body weight and other factors.

The driving force of a car, also known as the traction of a car, is the driving force that drives a pure car

1. The torque generated by the internal combustion engine of the automobile is transmitted to the driving wheel through the transmission mechanism, so that the driving wheel generates the circumferential force of the road surface as the rim of the car;

2. When the driving wheel has enough adhesion to the road surface, that is, the driving wheel does not slip on the road surface, the circumferential force of the wheel of the same length is generated, and the road surface in the opposite direction faces the reaction force of the driving wheel, and the car is driven in the opposite direction;

3. The torque generated by the engine of the liquid celery automobile is transmitted to the driving wheel by the driving system, at this time, the torque TT wheel acting on the driving wheel produces a circumferential force f0 on the ground, and the ground reaction force facing the wheel FT is the external force that drives the car, in addition, the force is called the driving force of the car.

It is directly related to the torque of the engine.

The main thing is the engine horsepower and body mass.

The small displacement has a lot of horsepower because of the addition of T, that is, turbocharging.

In general, in the traditional L-shaped engine, the combustion in the cylinder is pushed by normal air pressure. The turbocharger is like a pressure cooker, which increases the air pressure, so that the oil in the cylinder burns more fully and more fuel-efficient.

The car has a lot of horsepower, the power is strong, and there will be a lot of fun to drive, which is why many people are moving forward on the road of modification, if you feel that your car is not powered enough, and you want to increase the horsepower and torque, you can take a look at the ECU power upgrade of the HDP program, the effect is not bad, and it also provides brush insurance, which is more reliable.