Pool seepage prevention and plugging company, pool leakage plugging

You need this information about this company.

Pool leakage quick repair method:1. Surface repair method.

Due to the fact that the muddy water is not poured tightly during the construction of the pool, the whole is a little deviated from the pockmarked hole, and the water leakage will be formed after long-term water erosion and the waterstop is not fixed. At this time, we can use film materials (such as epoxy resin or resin-impregnated glass cloth) to lay along the surface of the cracks, especially for the vegetable washing basin, we must use non-toxic, non-polluting environmentally friendly materials.

2. Filling method.

If there is a large area of water seepage on the bottom plate of the pool, this should be a crack around the pool, such as a V-shaped or U-shaped groove on the surface, assuming that the crack is too wide, it is recommended to use resin mortar material for filling, or use impermeable mortar or asphalt and other materials to reinforce. After treatment, you need to wait for 7 hours before use, otherwise the filler material will fail.

3. Injection method.

Now people are accustomed to divide the whole porcelain plate into many pieces for bonding into a pool, and it is necessary to construct several blocks during construction, rather than the overall construction, so it is easy to form gaps. If the crack is small, an injection pipe can be set at the crack first, and then the repair material can be injected into the concrete, and then sealed with surface treatment.

The contents of the pool leakage plugging are as follows:

There are two main methods.

Method 1: Adopt the internal and external local non-leakage treatment, and then make the waterproof cement mortar of the bottom plate, roof and side wall of the pool 20mm thick.

Method 2: In the case that the water seepage problem is not serious, you can buy Ansai waterproofing agent, and then configure the mortar according to the proportion for use, this method can form a waterproof membrane, and the operation is very simple, and the waterproof performance is also very good.

Pool wall leakage plugging method:

1. When the pool is poured with waterproof concrete, due to the concrete consistency does not meet the requirements and the vibration is not sufficient, there will be problems such as small areas of honeycomb and rotten roots after the mold is removed, and only the surface layer is treated.

After adding water to the pool, due to the increase of water pressure, the weak part of the concrete leakage, the internal and external non-leakage treatment is adopted, and then the bottom plate, roof and side wall of the pool waterproof cement mortar plastering surface 20mm thick.

2. Generally, the plugging of the pool is caused by the leakage of the construction joints, if the construction joints are not cleaned up during the construction process, and the strength of the concrete does not meet the standard, the Ansai waterproofing agent can be purchased in the case that the water seepage problem is not serious.

Then according to the proportion of the mortar to use, this method can form a waterproof membrane, and the operation is very simple, waterproof performance is also very good.

The company's waterproof leakage repair refers to the waterproof leakage repair service provided by a professional waterproof company for buildings, roofs, basements and other places. Waterproof leakage repair is a very important work in building maintenance, which can effectively prevent the occurrence of problems such as water leakage, wall cracking, and ground deformation in the code brigade, and ensure the safety and stability of the building.

The company's waterproof leak repair service usually includes the following aspects:

1.Waterproof material selection: According to different places and needs, choose suitable waterproof materials, such as polyurethane, acrylic, asphalt, etc.

2.Waterproof process: According to different waterproof materials and places, different waterproof processes are adopted, such as brushing, spraying, membrane, etc.

3.Waterproof testing: After the waterproof construction is completed, the waterproof test is carried out to ensure that the waterproof effect meets the requirements.

4.Waterproof maintenance: Regularly inspect and maintain the waterproof layer of the town, find and deal with problems in time, and ensure the long-term effect of the waterproof layer.

In short, the company's waterproof leakage repair service is a very important job in building maintenance, which requires a professional waterproof company to provide professional services to ensure the safety and stability of the building.

Hello dear I am glad to answer for you: The following are some common leak repair waterproof manufacturers:1

Fujian Leidun Group ****2Guangdong Jiameili Building Materials Technology ****3Shenzhen Fengsheng Building Materials****4

Shanghai Jiayi environmental protection building materials ****5Hebei Huarui waterproof material ****6Guangzhou Xinhongda bent building materials ****7

Shandong Dingfeng polymer materials **** old 8Taixing Hongtai waterproof material **** extended information: leakage waterproofing refers to the use of special means to repair and strengthen the waterproof layer of buildings or other facilities when the waterproof layer leaks or is damaged, so as to achieve the effect of waterproofing.

The specific method and material selection of leak filling and waterproofing works depend on the location and condition of the leakage damage. The waterproof materials usually used include polymer, asphalt, polyurethane, etc., and the leakage filling waterproof project is mainly divided into two forms: cast-in-place structure and on-site rubber treatment.

For the basement waterproof plugging project, the high-pressure chemical grouting plugging construction should be carried out by the construction team with professionally trained personnel and professional construction equipment.

1. Cleaning: Inspect and analyze the leakage in detail, and determine the location and spacing of the grouting holes. Clean up the area that needs to be constructed, chisel out the precipitate on the concrete surface, and ensure that the surface is clean.

2 drilling: Use drilling tools to drill pressure relief holes around the hole, the diameter of the drill bit is 14mm, the drilling angle should be 45 °, the drilling depth of the structure thickness of 2 3, the drilling hole must be obliquely through the main leakage hole. However, the structure should not be penetrated, because the dust in the holes with large moving water will be washed away by itself.

The slow infiltration of the wall is to drill plum blossom holes on the seepage surface respectively. Rinse the grouting hole with a cleaning machine until the water from the grouting hole is clear, and then proceed to the next step.

3. Buried mouth: Observe the pressure of the main leakage hole, when the water flow is not urgent, the pressure is not large, you can use the quick-drying plugging agent to bury the grouting water-stopping needle, (according to the construction situation, you can also drive into the wooden wedge and then use the quick-drying plugging agent to plug it, and then re-drill the wooden wedge and install the expansion water-stopping needle after the structure is stable). When the structure reaches a certain strength and there is no leakage, the expansion water-stopping needle is installed in other drain holes, and tightened with a special hexagon wrench, so that there is no gap between the grouting nozzle and the borehole, and there is no water leakage.

The wall surface is slow to seep and is also installed with expansion water-stopping needles in turn. 25cm, 10cm and 8cm water-stop needles are installed at the leakage point according to the dislocation of the layer, so that the grouting can be completely dense from the deep layer to the surface layer. Plug all holes, crevices.

4 Grouting : Use a high-pressure grouting machine to test the pressure, which shall not exceed the pressure range of the concrete structure. Chemical grout material is poured into the grouting holes.

The single wells are performed one by one continuously. When the adjacent hole begins to be grouted, the pressure can be maintained for 3 5 minutes, and the grouting of the hole can be stopped and the adjacent grouting hole can be reinjected. Once all the holes have been filled, go back to the first grouting hole and grout again to ensure maximum pressure.

The grouting sequence of the wall is from bottom to top; After all the holes are filled, it is also necessary to return to the previous first grouting hole and recharge once.

5. Split the nozzle: 24 hours after the grouting is completed, you can remove or knock off the exposed grouting nozzle after confirming that there is no leakage. Clean up the spilled grout that has been cured.

Scope of application: water pressure plugging, subway, tunnel, pump room, reservoir, sewage pool, underground civil air defense cavern, basement garage plugging, cable trench, culvert, dam, power plant dam, acid (alkali) pool plugging, cooling tower plugging, mine, elevator shaft, tunnel rock foundation seepage, leakage, leakage, concrete engineering cracks, expansion joints, construction joints, structural joints of grouting sealing plugging, exterior wall waterproof plugging.

Hefei double waterproofGlad to answer for you :

Hefei double-entry waterproofing is relatively good. The degree of professionalism in the field of basement waterproofing and plugging is the most significant, with a young and high-quality construction team, scientific and technological waterproof instruments, and insisting on the use of green waterproof materials. The reputation of Shuangjin in Hefei is okay.

The main engineering areas are: building roof waterproofing; Basement waterproofing and plugging; The factory warehouse is waterproof and moisture-proof; Waterproofing works such as grouting and plugging.

Guidelines for basement waterproofing and plugging construction:

1. Surface layer method: suitable for large-area waterproof leakage, first select the concentrated location of the water flow to open the hole, drain the water inside the wall through the hole, and after it is completely dry, use cement mortar for smoothing treatment, and use polyurethane waterproof material for construction. The surface treatment of the base layer is smooth and smooth, and the uneven places are filled with cement mortar, and the surface impurities are removed at the same time, so as to facilitate the solid bonding of the waterproof layer.

2. High-pressure grouting method.

1) Use polymer nano plugging agent to plug the foundation leakage and carry out bottom waterproof construction.

2) The machine punches and arranges the grouting holes, which can be arranged into plum blossom shapes, triangles and slotted shapes. Grouting needles are buried every 50cm or so, and the pressure is controlled between them during construction. It can not only make the grouting material enter the concrete wall, but also will not damage the concrete structure due to pressure.

3) Select the grouting material according to the construction area. After the construction is completed, the grouting needle is removed.