DiskGenius rebuilds the partition table showing unformatted, urgent

Under normal circumstances, the ghost file should be restored to the C drive, and you mistakenly restored the image to the entire hard disk this time. Loss of the original partition caused by a mistake. If your partition structure is special, simply using partition recovery software, to a large extent, may not be able to find the correct partition data, wrong reconstruction, will destroy the original partition information, causing recovery difficulties.

If it's a notebook partition, it's often special.

It is because you are not familiar with the use of the software, and then it may be caused by the special situation of your partition.

If you are familiar with data recovery, this situation can be easily recovered, now the computer can start the Internet normally, and the original disk can be directly restored to the original def through remote assistance

g. With the right operation, the system does not need to be reinstalled. Do not write a large amount of data to your current hard drive. So as not to corrupt the data that may be recovered.

Be sure not to repartition, format, or anything like that. In that case, the recovered data is incomplete. Maintain the status quo.

To a large extent, the original data can be completely restored with proper analysis and processing. Without the need for data recovery software to scan the recovery. If you simply use data recovery software to scan and recover, it will take time and the effect is difficult to say.

If you want to try the recovery yourself, refer to scanning the recovery with data recovery software, and remember not to write the found files to the hard drive where the problem occurred. Instead, you should restore the found data to a different hard drive first. Make sure that the partition is correct before processing the problematic partition.

What is the format of your original CFF partition, fat32 or ntfs, if it is ntfs.

The data is still very recoverable,Show that the file system is damaged if it is not formatted,At this time, you must not format,It's dangerous,Generally as long as the file system is repaired,The partition can be opened normally,You can hi me。

I'll take a look at it for you.

That's what I do for data recovery.

1. Open DiskGenius, select the unformatted partition, and right-click and select [Format Current Partition].

2. In the format partition pop-up window.

Allocate unused drives in .

number, select "L" here, and click [Format].

3. Click [Yes] in the pop-up prompt to complete the partition formatting.

4. Turn on the computer, you can see that the partition has been displayed normally, continue to format another partition.

This issue occurs due to a system issue.

The solution and detailed operation steps are as follows:

1. In the first step, double-click the partition you want to restore directly, then unzip it, then right-click on the software icon and select the "Run as administrator" option, see the image below, go to the steps below.

2. In the second step, after performing the above operations, the program runs, directly double-click the disk to be restored, see the figure below, and go to the steps below.

3. In the third step, after performing the above operations, the program will quickly find the files in the same directory as the volume name of the disk to be recovered, see the figure below, go to the steps below.

4. Step 4, after performing the above operations, select the files you want to restore, and click the "Save File" option in the upper right corner, see the image below, go to the steps below.

5. In the fifth step, after performing the above operations, wait for the software to recover the data and finish, see the figure below. In this way, the problem is solved.

1. Double-click the partition that needs to be recovered, then unzip and right-click the software icon to select the "Run as Administrator" software (if it is an XP system, you can directly double-click to open the software).

2. After the Royal Hand program is running, directly double-click the disk that needs to recover data.

3. The program will quickly dismantle the found files and put them in the same directory as the name of the disk to be recovered.

4. Tick the files that need to be recovered, and then click the Save and Save buttons in the upper right corner to copy the files on the check.

5. The last step is to wait for the software to copy the data.

If the partition is OK but the display is not formatted, there is no problem with the partition table, but the DBR (boot sector) of the partition is corrupted. It can be repaired automatically with software, such as Eawo partition table doctor, etc.

For details, please refer to my space article "About Opening Partition Prompts Need to Format Data Recovery".

If you get an error when formatting a hard drive partition using the Diskgenius Partition Tool, it is usually due to a problem with the current hard drive. In general, if this kind of problem occurs and cannot be resolved by attempting, it is recommended to consider replacing the hard drive with a new one.

DiskGenius can't format the hard disk Solution 1, some users are using it"diskgenius"While partitioning the tool, you may encounter the problem of software lag on the boot interface of the software rubber and may even lead to system stuck.

2. Open"diskgenius"Partition tool, select the Hard Drive menu and find it in the menu"View the information"。Here, you can clearly view the current hard drive's power-on time, as well as information such as whether there is skin and bad sectors.

In general, if the hard drive has been used for a particularly long time, it can basically be considered to replace it. An aging hard drive can slow down the read and write speeds, which can affect the ignition of Windows, such as the staring speed and response speed.

The detailed steps to fix DiskGenius not formatting hard drive are as follows:

First, confirm that the drive is properly connected and active. You can check whether the hard drive shows sullen in My Computer. Slip pants.

Confirm that you have permission to format the hard drive. You can try running the computer as an administrator and reformat it.

If there are important files on the hard drive, you need to back them up to another storage device first

Situation 1: You can directly see the files in the partition in the software.

Select the files you want to recover in the software, then right-click and select "Copy to Specified Files", then save the files to another normal partition.

Situation 2: You can't see the data in this partition in the software.

Select this "unformatted" partition and click on the "Recover Files" button;

Click the "Start" button on the pop-up window. The default setting on this window is "Full Recovery" and does not need to be changed.

Once the scan is complete, you will see the files, then select the file you want, right-click and select "Copy to Specified File", and then save the file to another normal partition.