I didn t know there was something wrong with my water heater

Poor contact with electronic ignition,!

You can check if there is any leakage in the water pipe** connected to the water heater.

It may be that the contact is not good.

Landlord, such a problem, it is better to explain that the brand and technology are similar.

For example, Wanjiale 8L2, we know at a glance that it is a strong row machine, which is conducive to judging the cause of failure.

If it is equipped with a battery, it belongs to the model that the state compulsorily eliminates, if you are reluctant to throw it away for a while, find a professional to maintain it and then use it. Saving money is important, but life is priceless. Every winter, it is always a time when gas accidents are frequent, and it hurts to think about it.

In your case, consider from two aspects, one is the oxidation of the ignition needle, hit a dozen with sandpaper, and the other is that the battery is insufficient, try a new battery.

Hello dear! There are several reasons and solutions for the hot water heater but not hot water for your reference! 1. Check the setting of your water heater, there are many such cases, many users adjust the temperature to the lowest when using the electric water heater, or do not adjust it, so that there will be no hot water at all.

2. Whether the power supply display of the electric water heater is bright, if not, it may be that there is a problem with the thermostat, or there is a problem with the heating of the Shishu Royal Rod, and the after-sales service is based on its own brand. 3. Dongqing also has the problem of the thermostat jumping rock gate, generally the good electric water heater has dual thermostats, that is, room temperature control and over-temperature temperature control, these two kinds of temperature control are a kind of control of the display and control of the water temperature of your water heater, and one is to avoid the problem of normal temperature temperature control, for you to trip. That is, double insurance, some of them will directly lead to the inability to boil hot water because of temperature control tripping.

Calling a professional to turn on the machine quickly got it done.

Summary. 1. It may be that the water heater adjustment setting is not good, if the water heater does not produce hot water, you can check the setting of the water heater first, this situation is more, many users in the use of electric water heaters in the temperature adjustment to the minimum, or no adjustment, so that there will be no hot water at all. Therefore, you need to adjust the setting before using it and set it at the appropriate temperature.

1. It may be that the water heater adjustment setting is not good, if the water heater does not produce hot water, you can check the setting of the water heater first. Therefore, you need to adjust the setting before using it and set it at the appropriate temperature.

2. It may be that there is a problem with the thermostat whether the power display of the electric water heater is bright, if not, it may be that there is a problem with the thermostat, generally good electric water heaters have dual thermostats, that is, room temperature control and over-temperature temperature control, these two kinds of temperature control are a kind of display and control of the water temperature of your water heater, and one is to avoid the problem of room temperature control when the poor shed is used, for you to trip. That is, double insurance, Qingzi has some trips due to temperature control, which will directly lead to the inability to boil hot water. Called a professional Wang Ze to start the machine and it was done quickly.

3. It may be that the hot water pipe is blocked, and the water stop will directly cause the water heater to be unusable, because the principle of the surplus of the electric water heater is that the cold water runs against the hot water, and see if the water inlet of the water heater is blocked by the old match. In this case, you only need to unblock the blocked hot water pipe and let the hot water flow out fully, and you will be fine.

Hello for you to inquire, there is something wrong with the water heater, 1The reasons and corresponding solutions for the electric water heater are as follows: the tap water is cut off, and the waterway is checked; If the water inlet valve is not opened, check the water valve; The inlet and outlet pipes are blocked, and they can be used after cleaning the inner tank scale; The water pressure is too low, and it can be used normally when the pressure is high; The valve core of the mixing valve is stuck, the adjustment fails, and the mixing valve needs to be replaced; The safety valve is stuck, and the pressure relief handle of the safety valve is opened, and there is no water to accompany the town Hu Ming to be replaced; If there is no water in the inner tank or the water is not full, it can be filled with water; When the shower gear is in the off position, turn on the shower head switch.

2.Analysis and solution of the low temperature of the water for sale of electric water heaters: The handle of the mixing valve is turned to low temperature and adjusted to the direction of high temperature; The water temperature set by the thermostat is too low, and the temperature control temperature is set to a maximum of 75; The thermostat is broken, and the shaft of the rotating thermostat has no switch, which proves that it is broken and needs to be replaced; The distance between the thermostat and the heating element is too close, and it will be disconnected when it is less than 75, and the heating tube needs to be replaced if it is not heated to the set temperature, and water should be used in advance.

Solution: Wait until the heating indicator is off or the heat insulation light is on before use. The valve core of the mixing valve is damaged, resulting in collusion between cold and hot water, and the mixing valve needs to be replaced; The temperature sensitive probe fails, and the detection water temperature is inaccurate and needs to be replaced; If the heating tube is broken, the resistance measured with a multimeter is infinity (normal is tens of ohms), which proves that it is broken and needs to be replaced; The over-temperature protector is disconnected, and the internal parts need to be checked before it can be reset; The end of the outlet pipe is broken, causing the cold water to come out directly from the outlet pipe, and the end of the outlet pipe of the water heater is replaced.

Hello! There are many reasons why there is no hot water in the water heater, if we do not open the hot water valve of the water heater, there will be no hot water coming out in front of the water heater. Therefore, we usually remember to check whether its hot water valve is open before using the water heater, and only when the hot water valve is opened can the hot water be used normally.

If the hot water valve is opened but there is still no hot water, it is possible that the hot water valve is damaged, and it is generally impossible to repair it yourself.