Can the Redmi 1s mobile 3g version flash MIUI6

Hello. The current development version of MIUI 6 only supports Xiaomi Phone 4 and Xiaomi Phone 3, Unicom and Telecom and Mobile versions. On January 16, 15, Redmi 1S, the 4G version of the MIUI 6 development version also began public beta.

The Redmi Note 4G version is also adapted to the development version of MIUI 6!

The Mi Phone 2S and Mi Phone 2A have been adapted to the special edition of MIUI 6.

The stable version of MIUI 6 is temporarily adapted to the following models: Xiaomi Phone 3 series and Xiaomi Phone 4, Redmi Note 4G version series!

Redmi 1S mobile 3G version cannot be flashed MIUI6.

Since MIUI6 is based on Android for deep customization and optimization, the Redmi 1S mobile 3G version was launched relatively early, it is Android, so it cannot be adapted to MIUI6.

Xiaomi officially released its latest MIUI 6 system in Beijing's 798 art district on August 16, 2014, the interface adopts a colorful and flat design style, using color to set off the content, and the notification bar can change color with the application notification or application background; MIUI 6 simplifies the icon design, making the system icons highly recognizable. In addition, MIUI 6 also uses colors to set off the content, and the notification bar can change color with app notifications or app backgrounds, making the entire phone interface very harmonious. At the same time, MIUI 6 also adds a variety of new animation effects.

The Redmi 1s mobile 3G version cannot be brushed into the Unicom 3G version of the mobile phone, which is determined by the hardware of the mobile phone and cannot be changed.

The parameters of the mobile network of the Redmi 1S Mobile 3G version are as follows:

As can be seen from the figure above, the mobile phone supports mobile 3G 2G network, and at the same time supports China Unicom 2G network, and does not support China Unicom 3G network.

Therefore, if the mobile phone is inserted into the Unicom 3G mobile phone card, it can only use the Unicom 2G network.

Hello. Redmi 1s can only be swiped.

Redmi mobile phone card swiping method.

Place the flashing package in any folder.

Open System Update, select the installation package in the menu key, and update it now.

The second method of card swiping needs to enter the REC mode of the mobile phone, and there are two ways to enter the REC.

The first method, click System Update, click the Menu key to select Reboot to Recovery, click OK, and the phone will reboot into Recovery mode.

You can see a small green Android robot in Linghui Lead, press the power button to enter REC mode.

The second method, in the shutdown state (buckle the battery to turn off), press and hold the power button and the volume down ruler button at the same time, light up the screen and release the button.

Then you'll see three options.

Recovery mode means to enter REC mode.

fastboot mode means to enter the wire brush mode.

norma boot means reboot.

At this time, the volume down button is the selection key, the volume up button is the OK key, and the power button is useless.

Press the volume down button to move the cursor to recovery mode, then press the volume up button to confirm, and wait for a few moments for it to appear.

A green android robot lying on the ground, finally press the power button to enter.

At this time, the volume up button is the confirmation key, and the volume down button can be selected, 1, select apply update from sdcard, 2, and then you will enter your SD card directory, find your ** good flashing package and select OK, and then start flashing.

3. Wait for the end of the progress bar, press Back, select [Reboot System Now], and the phone will start to restart automatically.

Note,System upgradeAs long as you turn on the system update,Update it immediately,Downgrade must be cleared before booting,Otherwise, it will be stuck or the software will crash。

2 Tap MIUI at the top

3.Click to go to the forum.

5.Click on Redmi 1s

Hello. For more information about MIUI6 adaptation, see

Connect the computer to flash the package with one click.

You enter Xiaomi's official **, there is a tutorial in it.

Hello. The address of Xiaomi's official website.

Reason: Redmi 1S mobile 3G version does not support 4G network from the hardware.

The mobile phone can only be brushed with the flash package adapted to the model, otherwise there may be serious consequences (such as: bricks) Redmi 1s mobile 3G version:

Main screen size: inches.

Main screen resolution: 1280x720 pixels.

Rear camera: 8 million pixels.

Front camera: 1.6 million pixels.

Battery capacity: 2000mAh

Battery type: Removable battery.

CPU: Quad-core.

RAM: 1GB