-
Repairs are required. Reason: 1. The inverter cabinet shows that P1 is too high or too low voltage protection.
2. The fixed-speed hang-up shows that P1 is the speed stall of the indoor fan.
3. The inverter hang-up shows that P1 is too high or too low voltage protection.
Solution: Turn off the air conditioner and wait for 5-10 minutes, let the air conditioner cool down, restart it, the P1 signal will be gone, and the air conditioner will operate normally.
Because with the continuous growth of the use time of the air conditioner, all parts of the air conditioner are prone to various problems, when the Midea air conditioner fails**P1, it means that the voltage of the air conditioner is too high or too low at this time, and the fault part of the air conditioner generally appears on the outdoor electronic control of the air conditioner and the PFC module.
Explain other faults according to the paper version of the manual**.
P0: At this time, the air conditioner has four current protections.
P2: The indoor version of the air conditioner does not communicate with the switch board of the air conditioner for up to two minutes.
P3: The temperature sensor of the indoor evaporator of the air conditioner has a short circuit or an open circuit.
P4: The temperature sensor in the indoor room has an open circuit or a short circuit.
P5: The air conditioner's indoor fan temperature fuse is disconnected.
P6: There is a fault in the zero-crossing inspection link of the air conditioner.
P7: There is a certain error in the model selection.
-
P1 is generally too high or too low voltage protection tips, it is recommended to see if the voltage of your home is stable, especially when multiple high-power electrical appliances are running, in addition to try to contact the after-sales service for professional maintenance.
-
Summary. p1"Error** usually refers to a malfunction or abnormality in the air conditioner's electrical control board, which usually requires a professional technician to repair or replace. If your aircon shows P1, it is recommended to turn off the aircon switch first, then wait a few minutes before turning on the aircon to see if the fault clears**.
If P1** persists, then you need to seek help from a service professional. <>
p1"Error**Usually the imitation of the finch refers to the failure or abnormality of the electronic control board of the air conditioner, which usually requires the maintenance or replacement of professional technicians. If your aircon shows P1, it is recommended to turn off the aircon switch in the morning, then wait a few minutes before turning on the aircon to see if the fault clears**. If P1** persists, then you need to seek help from a service professional.
Approximate how much.
Normally, the failure of the outdoor unit P1 may be due to the following reasons: Circuit fault: There may be a problem with the electrical noise circuit board of the outdoor unit, which needs to be repaired or replaced.
Sensor failure: The temperature sensor and humidity sensor of the outdoor unit may malfunction and need to be checked and replaced. Fan failure:
The outdoor unit fan may malfunction and needs to be inspected and repaired. Other hardware failures: e.g. compressors, circuit boards, etc., may fail and need to be repaired or replaced.
Dear, these are all possible reasons for bumping, but the specific situation may vary depending on the device family model and manufacturer.
Dear, are you asking how much it costs to fix this fault? <>
That's right. Probably between 400-700. <>
The cost of repairs is affected by a variety of factors, such as the number of parts that need to be replaced during the maintenance process, the cost of parts, the difficulty of the repair technique, the number of hours of repair, and so on. In addition, different service providers will also have different services in front of the cave and in the region.
It's so expensive.
Dear, if the warranty period has passed, the master needs to pay for door-to-door maintenance. It is recommended that you find a few local air conditioning maintenance service providers for consultation, ask about their service costs and maintenance details, compare the ** and reputation between different service providers, and then choose the right maintenance service provider to carry out repairs. <>
Each region is **different.,I'm telling you the general**.**, you can first consult Qi Fu with the local brother Xi Brother to consult the master of the maintenance of the opening boy, it may be cheaper. <>
-
Dear, does the air conditioner show P1 needs to be repaired? A: Repairs are required.
The power supply voltage is too high or too low, and the air conditioner reports a fault, and the maintenance check fault ** determines that the machine shows that P1 is too high or too low voltage protection. The door-to-door measurement of the user's power supply voltage, the standby state is 225V, Pi Xiangliang meets the requirements of air conditioning operation. The details are as follows:
1. The display of P1 is due to the air conditioner power supply voltage is too high or too low, resulting in the air conditioner reporting fault, and the fault is in the outdoor electronic control, PFC module, and frequency conversion module; It needs to be repaired, and it is not recommended to repair it yourself; 2. You can first check it by yourself to make sure that the P1 is too high or too low for protection. Measure the power supply voltage buried in the house, and the standby combustion width state is 225V, which meets the requirements of air conditioning operation;
-
The air conditioner shows P1 to indicate that the voltage is too high and too low protection, this situation needs to be repaired by professionals, and it is not recommended to repair it yourself.
Specific reasons: 1. The display of P1 is due to the air conditioner power supply voltage is too high or too low, resulting in the air conditioner reporting fault, and the fault is in the outdoor electronic control, PFC module, and frequency conversion module.
2. It may be that the ambient temperature is too low to cause protection, in this case, Bi Mingrang is set to set the local temperature and the indoor and outdoor ambient temperature is too low (generally lower than 22 degrees), and the air volume is too low, the air conditioner is normally protected, and the temperature can be lifted after the temperature rises.
3. It may be that the filter screen is dirty, the filter screen or the indoor heat exchanger is dirty, resulting in low air volume, and the system cannot exchange heat in time resulting in the indoor coil temperature is too low, in this case, it is recommended to clean the filter screen or indoor heat exchanger.
4. It may be the fault of the fan and related circuits, and the failure of the fan and related circuits will cause the air volume to be low, and the system cannot exchange heat in time, resulting in the temperature of the indoor coil unit being too low, in this case, it is recommended to send it to the after-sales service.
5. Connect the terminal of the main relay to the other end, the machine runs stably, the refrigeration effect is very good, when the relay terminal is restored to the normal installation state, the fault reappears, so the main relay on the external electrical control board is determined to be bad.
The above content reference: Encyclopedia - Gree air conditioner failure**.
-
Summary. Extended addendum: There can be a variety of reasons for the P1 error in the air conditioner**, such as a faulty water pump, a blockage, a blocked water connection, and so on.
If you do not repair it in time, it may cause the air conditioner to not work properly, affecting your experience. Therefore, once you find a P1 error**, it is best not to delay and contact a professional maintenance personnel in time to deal with it. At the same time, it is also necessary to pay attention to the maintenance of the air conditioner, and regular cleaning and replacement of the filter can effectively extend the service life of the air conditioner.
Hello, the error of P1** usually indicates that the air conditioner's water pump is out of order or missing and the water circuit is blocked. If your air conditioner shows a P1 error**, you need to repair the first draft in time. It is recommended that you contact a professional aircon repairer immediately to inspect and repair your aircon.
Do not attempt to repair it yourself to avoid causing more damage. Once the repair is complete, your aircon should be working properly.
Extended supplement: There may be a variety of reasons for the P1 error in the air conditioner, such as pump failure, blockage, water channel failure, etc. If you do not repair it in time, it may cause the air conditioner to not work properly, affecting your experience.
Therefore, once you find a P1 error**, it is best not to delay and contact a professional maintenance personnel in time to deal with it. At the same time, it is also necessary to pay attention to the maintenance and excavation section of the air conditioner, and regular cleaning and replacement of the filter can effectively extend the service life of the air conditioner.
Chigo inverter air conditioner shows P1, indicating that the evaporator temperature protection of the air conditioner is faulty, if there is a system failure, please contact a professional for repair, you need to clean the evaporator or replace the indoor unit of the air conditioner. >>>More
I think the analysis of the roof is basically in place, and the mobile phone really doesn't have to say. Power saving is really good,The picture is also very good,I also think that the foreign sound quality of Huawei mobile phones has always been really not outstanding,Mediocre! The same goes for headphones, a good horse is not a good saddle. >>>More
Huawei P10 is very good, the following are the specific parameters of the phone: >>>More
The Huawei P10 system is equipped with an octa-core Kirin 960 >>>More
The price of these two machines is about the same now.,If you want to play with the machine, choose S1,If you want to use it as a mobile phone.、If you like to shoot something with a mobile phone, you can choose P1.,To be honest, I feel that S1 is more feminine.。 P1I2200 or so,S1 is not recommended,If you want to buy it, you can buy itS1 Elite Edition,The price of water is almost 2500 below,If you are better to buy a machine,It is recommended that you go to see the O2 machine。 The configuration is much higher, and the price is also kind. >>>More