How do I enter a lower horizontal bar in computer operation?

How to enter the lower horizontal bar in the computer operation You need to press shift+ (the key between 0 and + on the keyboard) in the English input state, and the input result is " ".

1. It is a fixed key on the computer keyboard, which can be typed without special operation.

2. The computer keyboard is a channel that inputs the control information of text information into the computer, which has evolved from the keyboard of the English typewriter. When it first appeared on computers, it was a component called a "teletypewriter".

Extended Materials. If you type it out in this way, it may be that the computer keyboard has the following malfunction:

1. The button cannot be bounced.

The main reason for this type of malfunction is poor keyboard quality.

Solution: Restore the stuck key to its original position, the best way is to remove the keycap and deal with it simply, such as replacing the spring.

2. Problems with the internal wiring of the keyboard.

The internal wiring problem of the keyboard is manifested as two or three letters appearing at the same time when pressing a key when entering text, or a certain row of keys cannot be output.

Cause of failure: The wiring inside the keyboard has a short circuit or open circuit.

Solution: Disassemble the keyboard to clean the inside of the keyboard, or find the circuit break point and weld it.

3. Interface problems.

This type of fault phenomenon is manifested as a prompt "eyboard error or no keyboard present" when the computer is turned on, or the system crashes directly after booting.

Cause of failure: The keyboard is not properly connected, the pins of the keyboard interface are bent, and the keyboard or motherboard interface is damaged.

Solution: Go to the repair point for warranty.

Are you asking how to enter "down the dash" in the computer start-run and then a character command box appears? Directly press and hold "shift" and the key next to the number key 0 in the upper row, which means that there are two horizontal bars on the top.

The detailed steps of "Computer Keyboard Input" are as follows:

1. First, press the shift key.

2. Switch the input method of the computer.

into English.

3. In English, press and hold the "Shift" key on the keyboard.

4. Keep the shift key unreleased, and then press the " " key on the keyboard to enter the lower horizontal bar.

5. Press the " button again to complete the input.

1. Switch the input method to English input.

2. Hold down the shift key.

3. Press the key.

In this way, a bar comes out of the run.

I don't understand what you mean! Is it typing or something else?

1. Under the English symbol, press the keyboard shift and add the "-" sign, such as: Chinese: ——

2. Select "Start" - "U" in the font and then enter, you can type the lower horizontal line.

3. The configuration of the computer is the standard to measure the performance of a computer. It is mainly determined by the CPU, graphics card, motherboard, memory, hard disk, monitor, chassis, optical drive, keyboard, mouse, and cooling system.

The specific steps for the computer's keyboard to type the lower dash symbol are as follows:

The materials we need to prepare are: computer, word document.

1. First of all, we open the word document and enter the page.

2. After the destruction, we press the "shift" button to switch the English mode to enter the waiter method.

3. Then we press the "shift+-" key combination on the keyboard, and we can enter the lower horizontal bar symbol.

Question 1: How to type out the horizontal line with a computer? Method:

1. Under the English symbol, press the keyboard shift plus "-sign Furu: Chinese:

2. Select "Start" - "U" in the font and then enter, you can type the lower horizontal line.

Question 2: How to enter the lower horizontal bar in the computer operation The method of entering the lower horizontal bar in the computer operation:

1. Click Start Run.

2. Click in the pop-up run dialog box to let the cursor be displayed in the run box.

3. Switch the input method to English input.

4. Hold down the shift key.

5. Press the button.

In this way, the running bar "" comes out of the run

Question 3: How to use the keyboard to make horizontal bars? The lower horizontal line can only be typed if it is supported by the typesetting software. Select the u with a dash above the software or web frame (as shown in the red circle in the figure below), and the characters typed, including spaces, will have a dash under the dash.

The underline is the horizontal line below the attack to emphasize the text and attract attention. Underlining can only be typed if it is supported by the typesetting software. Select the underlined u above the software or web frame, and the typed characters, including spaces, will have an underscore.

Combining software and input methods, as well as needed, there can be a variety of ways to hit the crossbar:

1. Enter the minus sign continuously;

2. Continuously enter underscores;

3. Select the soft keyboard Tabs in the input method (such as Sogou input method) to select the horizontal tab input;

4. In Word or WPS, on the far left side of the line, enter 3 minus signs and press enter, you can hit a horizontal bar of the column. Enter 3 , *, or you can try it yourself.

Question 4: How to type the lower dash symbol on the computer's keyboard? Are you talking about underlining? Under the English input method, or under the English punctuation, use shift+the key on the right side of the main keyboard area 0 to the right of the Chinese can not be typed.

Question 5: How to draw a horizontal line on the computer? Click on shift+-, which is 0 next door.

Question 6: How to play the lower horizontal bar of Lenovo laptop After converting to English input, shift+minus sign is pressed at the same time (it is the - sign on the left of the equal sign key in the upper row).

Question 7: How to make the horizontal line typed on the computer at the bottom right of the word You mean that there is an empty horizontal line on the right side of the word, right, then after typing, select the tool below the u in the above tool and follow the horizontal line, and press the space bar.

Question 8: How to hit the lower horizontal line? Is this what you're talking about?

Change your input format to a medium-sized slippery British and American keyboard format, then hold down Shift plus the keys indicated in the diagram.

Question 9: How to hit the short lower horizontal line ( Which one are you?) The first one, the second type of shift+minus key in Chinese layout, the third type of minus key in Chinese socks layout, and the shif+minus key of English plate format (become English input method) hope to help you.

Question 10: How to type the lower horizontal bar of the computer wifi account Switch to English typing mode, and then hold shift+-=

Short horizontal bar key. Notebook: The dash key is to the left of the "+" key.

Desktop: The horizontal bar is to the left of the "+" key.

1. Switch the input method to English input.

2. Hold down the Shift key of the Sparrow Brigade.

3. Press the button to stare at the stool.

In this way, a bar comes out of the run.

Summary. Hello.

Hello. Are you going to enter the vertical bar directly?

Is that what it is?

The computer enters a horizontal bar and it becomes a vertical bar.

Displays vertical bars. Did you enter this build?

Enter on the numeric keypad.

You see the one I drew in a circle, and that's the horizontal bar.

Click on this.

All right. It's just behind 0, see it.

Okay thank you. Good.