What to do if there is such an interface on your Dell computer

Your system looks like it's having trouble booting.

It is recommended that you turn off the power and turn it on again, press F12 to enter the boot option, click on the word: diagnostics, enter the self-test mode, and see if there is any hardware failure.

The Dell icon keeps showing that the Dell icon cannot enter the system when the computer is turned on, indicating that the computer has failed to pass the power-on self-test. You can do the following to troubleshoot the problem.

1. If you can't enter the system when the motherboard logo is displayed at boot, you need to restart and press the Tab button to skip the logo screen or press the F2 key when booting up (the notebook is generally F2 or other designated hotkeys) to enter the CMOS setting interface, in Advanced BIOS

In the Features tab, turn off the Full Screen Logo Show to see if the POST information can be displayed, and then follow the relevant prompts to determine the problem.

2. Under normal circumstances, if there is a prompt message with white characters on a black background on the screen, you can press the F1 key to skip the non-fatal error and start the computer directly, or press the F2 key to enter the CMOS, and then press F9 to load the predefined parameters or select Load optimized

defaults (load high-performance defaults) or load fail-safe defaults, and press F10 to save and exit the restart.

3. If the above operation is invalid, it means that there is a problem with the hardware, generally the memory and the hard disk may be in poor contact or the hard disk boot sector is damaged, and it is necessary to reinsert or repair the boot sector or reinstall the system or replace the hard disk.

The Dell laptop can't be turned on, it keeps stopping at the boot interface, and the fan keeps running at high speed, which may be a serious heat, and if you solve the heating problem, you can solve the fan problem.

There are several causes of fever:

1.If the heat dissipation port is blocked, you need to open the back case of the notebook, get the blocked heat dissipation port through, and use a cotton swab leather to remove the dust on the fan.

2.It is also possible that the laptop has been in contact with the desktop for too long, if it is not an office, you can buy a desktop cooling fan, remove the fan, and put the heat sink on the laptop where the heat is very hot, which can also help heat dissipation.

3.Sometimes the computer running the program configuration is too high, which will also cause the laptop to heat up, you can press the Ctrl Alt del key to enter the Windows Task Manager, and check if there are any programs that are consuming computer resources.

This tip is to tell you that the boot partition was not found, there may be the following reasons:

If the hard disk is not found (if you can't find the hard disk after restoring the BIOS settings, open the case and plug in the data cable and power cable of the hard disk again after power off to prevent poor contact).

The system partition is not activated due to an accident (the computer relies on the activation flag to determine which partition to boot the system, boots to PE with a USB flash drive or CD-ROM, and reactivates the partition with the tools in PE).

What you pop up is actually the browser.,Your browser should have started this boot self-start.,That's why it will pop up when it starts.,You need to turn off the boot of this browser and it won't pop up.。

This page pops up on your Dell computer, you can repair the operating system, or reinstall the operating system. A reloading system solves this problem.

The last correct configuration: Before booting the boot and not entering the operating system, we press the F8 key, select "Last correct configuration" and press enter. This method can only solve the situation that the system can not be entered due to configuration problems, because this method is simple to operate, so this method should be taken first when there is no way to enter the system, if it cannot be solved, replace other methods.

This is what you've been doing recently.,Is there any software installed that causes the browser to open the interface? What kind of junk software pop-up window is this? It is recommended that you use an antivirus software to see if there is any rogue software.

Otherwise, the browser will not pop up as soon as the computer is turned on, and only a neat desktop will be displayed, unless you have recently installed some junk software, or some junk software that comes with it again.

Manage with PC ManagerPop-up programwithBoot up the itemto view and close the Internet Explorer.

1) The motherboard BIOS is out of power, and you can't remember the hard disk information, if your system date is incorrect, it is likely to be the reason. Solution: Replace the BIOS battery and re-enter the BIOS to detect the hard disk.

2) The IDE cable is of poor quality or is not well plugged in. Solution: Change an IDE cable or plug the IDE cable into another IDE slot on the motherboard, do not connect the hard disk cable with other IDE devices, such as optical drives, separate the two IDE cables, and set the master and slave disks correctly.

3) The hard drive is faulty and may need to be replaced.

4) If your computer can detect the hard disk every time and cannot enter the system, reformat the hard disk completely, and then reinstall the system (if you can enter the safe mode to restore the system, try it).

5) Also set the hard disk to boot to try (is it wrong).

6) There is also a situation where replugging and unplugging the memory and cleaning the gray can also solve the problem (sometimes caused by it).

7) If you can't solve it yourself, it is recommended to overhaul it.

This is a browser that enables the computer boot startup,Use 360 or security manager to disable boot and start the software,Prohibit it from appearing next time you boot it。

Summary. Hello, what interface appears when you boot up?

Dell computer boot appears this interface is what's going on, Dell's machine w10 system.

Hello, what interface appears when you boot up?

Wait a little longer for it.

Fully loaded. Wait a little longer.

Yesterday I waited for more than 1 hour, and then something happened, and it was forced to shut down.

There is a problem with the system, so if you want to be more direct, you can redo the system.

Can you guide no.

Yes, but a system USB flash drive is required.

I didn't. You turn on the computer and press F2, restart it a few more times to try.

Take a look at the forced skip over.

The Dell laptop can't enter the system when it is turned on, and this screen appears, what's going on? What to do?

Boot press f8 to do not move to the advanced option appears in the let go, select "the latest correct configuration" enter to repair, it is not possible to press f8 to enter the safe mode to restore the system or reinstall the system. If it is caused by hardware problems, discharge the BIOS battery (restore the BIOS factory default) It is recommended to plug and unplug the graphics card and memory, clean up the hygiene, and polish the gold finger of the graphics card and memory (there is also whether there is a problem with the hard disk, ** software repairs the bad sectors of the hard disk, and you can also format the hard disk to repartition and reinstall the operating system, if it always doesn't work, it is recommended to overhaul it). Use the system that comes with the system restore method:

The system comes with the system restore: "Start" "Programs" "Accessories" "System Tools" "System Restore", click "Restore my computer to an earlier time", press Next, you will see that the date page has a dark date, that is the restore point, after you select, click Next to restore (win7 restore the system, in the control panel then the device and security sub-option and then the backup and restore sub-option).

1. It is recommended to power off directly after booting the system, and after repeating the three changes, you can enter the safe mode, select troubleshooting, advanced options, and enable the safe mode. 2. Then after entering the safe mode, insert the Windows installation disk, press the Win+R key combination to trap high, enter SFC ScanNow in the run box, and click OK to repair the system.

3. If after the repair, restarting Wang Jianqi still doesn't work, directly use the windows installation disk to boot and install the operating system new. 4. If the original version is the same after installation, there may be a problem with the hardware, try to replace the memory, hard disk and other hardware, find the problematic hardware, repair or replace it.

<> time of day not set, the date and time are not set.

Probably the motherboard battery is dead, and the BIOS settings information cannot be saved.

Go into the BIOS and set it up, and it should work normally.

However, it should still be like this when the phone is turned off and turned on again, which requires a change of button battery.