There is a wireless router at home, how can Konka LED32IS97N connect to the network?

Dear Konka users:

Hello, LED32IS97N, if you use wireless connection, please set it as follows:

1. For wireless connection, please operate as follows:

1. Wireless connection needs to be matched: wireless network card (it is recommended to use RTL8191SU, RTL3070, RTL8712 as the main chip wireless network card, drive-free, plug and play), wireless router, computer, network TV;

2. After the wireless router and the computer can be connected to the network normally, please connect the wireless network card to the TV;

3. TV menu-Network Settings-Wireless Settings-SSID(Search for router devices)、Encryption type(Same as set on the computer)、IP typeSelect automatic getting,Finally, click Settings。

2. Note when the wireless connection cannot be connected:

1. Please make sure that the wireless router and wireless network card used are normal and can be used;

2. The signal strength of the wireless network is too low (when the strength of the wireless network you use is less than 35%, although our machine can detect the network, it cannot be successfully connected.) In order to ensure the normal use of the wireless network, the signal strength is required to be stable at more than 70% or more than two bars. ）

3. When there is a wireless connection, you can search for the signal, but the connection fails, you need to check: encryption type, WEP length, and whether the WEP mode settings are correct. Please confirm the parameters set by the encryption method,Our TV can be recognized normally:

a) Use WEP encryption mode, set as follows: open for authentication mode, 64bit for wep encryption, ASCII for key mode, any one key can be set, and the password needs to be set to 5 digits. (b) WPA encryption is adopted, and the settings are as follows:

Set the password type to TKIP, select psk for PSK EAP, and set 8 digits for the password. (Note: The password is recommended to use the numbers 0-9 for easy identification of TV).

Connect the external network cable to the WAN port of the router, and connect the computer to the LAN port of the router (there are four, any one is acceptable), and connect the power to the router.

Open the IE browser, enter in the IE address bar, and the gateway address that different brands of routers may log in will be different, such as some gateways, which are generally indicated on the sticker on the bottom of the router, including username and password). , and then press enter, a small login page with username and password comes out, the initial username and password are admin, after entering, click "OK" to enter the router settings interface.

There is a "Quick Settings" option in the menu bar on the left side of the router settings interface, click on it, and then a page will come out to let you choose the Internet access method (if China Unicom or China Telecom, choose the PPPOE method if you give the password, if you give a group of IP addresses, select the static IP mode, and remember to fill in the local DNS when filling in the Internet broadband information).

Then click Next, save the broadband information (password, or fixed IP address) to the router, and then restart the router (method router menu bar at the bottom of the "System Tools" - "Restart Router"), you can surf the Internet.

You haven't even figured out the question, is it a wireless connection or a wired connection? It's a good idea to see if the settings of your router and your TV's settings match.

Dear users: Hello, thank you for your support to Konka. If the TV needs wired networking, you need to equip a router and network cable, connect the network cable to the TV through the router, router setup steps:

1. The computer IP is automatically obtained, please check the computer manual or verify with the computer after-sales call. 2. Restore the router to factory settings and reset the router parameters. TV Setup Steps:

1、The TV is cut off and the power is restarted,2、Menu-Settings-Network-Wired Segment-IP Type from the World to Obtain - Settings - Network Detection。

If the TV needs wireless Internet access, you need to connect to the external wireless network to search for the vertical card to use, there are requirements for the chip model of the wireless network card, and the chip models that can support the wireless network card are RTL8191SU, RTL3070, RTL8712. What our TV can identify is the wireless encryption method:(1)Adopt WEP encryption,Set as follows:

Select Open for authentication mode, 64bit for WEP encryption, ASCII for key mode, set any one key, and set 5 digits for password. (2) WPA encryption mode is used, and the settings are as follows: the password type is TKIP, PSK EAP is PSK, and the password needs to be set to 8 digits.

Dear Konka users:

1. Select the IP address in the computer to be obtained automatically.

2. Restore the router to factory settings and reset the router parameters. (Enter the ** of the router, log in to the relevant settings interface, and enter the broadband account: username and password) to confirm the save.

The steps to set up the TV are:

1、The TV is cut off and the power is restarted,2、Click the menu on the remote control--Settings--Network--Wired--IP type automatic acquisition--Settings--Network detection,The detection is successful;

If you are connected wirelessly, please do the following:

1. Wireless connection requires Spike limb matching: Wireless network card (it is recommended to use RTL8191SU, RTL3070, RTL8712 as the main chip wireless network card, drive-free, plug and play; If the TV has a built-in wifi function, it is no longer necessary to configure a wireless network card), a wireless travel device, a computer, and an IP TV.

2. After the wireless router and the computer can be connected to the network normally, please connect the wireless network card to the TV;

3. The router adopts WPA encryption mode, and the settings are as follows: the password type is TKIP, the PSK EAP is PSK, and the password needs to be set to 8 digits. (It is recommended to use pure numbers for passwords to be easy to identify).

4. TV: Settings - Network - Wireless Settings - SSID (search for router devices), encryption type (the same as set on the computer), IP type Select automatic acquisition, and finally click Settings.

5. If it is a built-in wifi function, settings - network - wireless settings, turn on wifi, select the name of your router, a dialog box will pop up, prompting you to fill in the password, please use Konka remote control keyboard and mouse to enter the input. After entering, click the Nian family stool to connect, and then click the network detection. If the TV prompts that the network has been restored and the network is connected, it means that the TV has been successfully connected to the Internet!

Dear users:

Hello, sorry for the inconvenience caused by the product! Based on your description, it is recommended that you follow the steps below for wireless network connection:

1. No noisy sliding wire connection needs to be matched: wireless network card (wireless network card needs to be purchased and matched by the user, if the built-in wifi does not need a wireless network card), wireless router, computer, network TV.

2. Set the encryption parameters of the router. It is recommended that you use the WEP encryption method, and set the following settings: open for authentication mode, 64bit for wep encryption, ASCII for key mode, any one key for one, and 5 digits for password.

Alternatively, use WPA encryption and set the password type to TKIP, PSK EAP to PSK, and set the password to 8 digits. Passwords are recommended to be purely numeric.

3、Turn on the TV and enter Settings-Network-Wireless Settings-SSID Select the name of your router,There will be a dialog box popping up,Prompt you to fill in the password,After entering, click on the settings first,Then click on the network detection。 If the TV indicates that the network has been restored and the network is connected, it means that the TV has been successfully connected.

The default effective wifi terminal of the telecom cat is 4,The fifth connected one can't go online,It can only show that it is connected,You need to crack it。

If you want to connect to wifi, you must first set up your router, then turn on your TV settings - wireless settings function, search for the wifi signal that was set before, and enter the password to connect.

If it is wired, you only need to plug the network cable into the TV network cable interface.

This doesn't use WLAN, you can only plug in the network cable. It's good to split the root line to the top.

This requires buying a wireless network card that the TV can support.

I'll tell you I don't know.

The IP address should also be set on the TV.