Wireless routers. Networking issues. Wireless router internet access issues

There is no doubt that the problem should be approached in this way:

First, see if the router is faulty. Method: Disconnect the router and connect directly to the cat dial-up Internet, if it can be on, it means that there is no problem with the cat and the external line.

Second, reset the router again, and then connect it to the modem to reset the router settings. Third, the IP and setting method of the specific router can be seen at the bottom of the router, which is generally available. Not necessarily, it may also be 1+, depending on the specific brand.

Fourth, if this doesn't work, then the preliminary judgment may be that the router is broken! Just give it a try! ]

1.First, check whether the line is unblocked, such as whether the modem and the port are connected, and whether the connection between the modem and the router is correct.

2.Restart the route.

3.If that doesn't work, check with your carrier to see if the network has been disconnected.

But it's normal for this to happen, and it's usually connected again after a while.

Simple wiring problems are passed, after checking, if there are still problems, please use the desktop to log in to the wireless router settings to see, wireless router settings.

Enter http: Enter the user, password, admin, admin

In the dialog interface, Wireless Parameter Settings Basic Settings: Turn on the wireless function Try again.

Enter http: or press enter and enter the user and password admin, admin, and check whether the computer and the router are connected.

The computer is set to automatically get an IP address.

Enter the router management interface, and a "Setup Wizard" interface similar to the following figure will pop up, select the next step and follow the prompts.

3. Assuming that your broadband access mode is ADSL PPPoE, then select "WAN Port Connection Type" as "PPPoE", fill in "Internet access", "Internet Password", and then select the connection mode as: "Automatic Connection", and click "Save" to complete the configuration; After saving, the password filled in the "Internet password" box will have a few more digits, which is specially made by the router for security reasons, and the basic settings of the router are completed.

4. Set up the reboot to open the browser to access the Internet, the above are the most basic settings.

Ping your router's IP first to see if there is any data loss?? The time should be within five seconds, if it is normal, it is recommended that you look for the Netcom service to see if there is a problem with the switch you have.

1. Let Netcom's cable connect directly to your host to see if it is normal, if it is normal, it means that there is a problem with the router.

2. In general, this situation is unlikely to occur on the router, and you can restore the router to factory settings.

3. System reinstallation does not mean that there is no problem, whether other partitions are in the Trojan, etc., it is recommended that F8 enter the safe mode with network connection, and test the Internet!

There are account and password settings in the route Under normal circumstances, your computer has been able to surf the Internet normally As long as the account and password are set correctly, but you can use wireless Remember to set the IP and DNS in the wireless network settings Refer to the settings in the local connection I hope it will be useful to you.

Elegant little gathering Hanni Fang.

1. All your desktops need to buy a wireless network card, within 100 yuan**. It's best to buy the same brand as your router, and some different models have compatibility problems.

General wireless routers have a hub function, which can be directly connected to the network cable.

If you want to connect to a desktop computer wirelessly, you need a wireless network card. Once the driver is installed, you can use it to search the net. Search for your own home Wi-Fi and connect to it.

However, for the sake of security, it is necessary to encrypt the wireless router and set the access password. When the wireless network card is connected, you need to know this password.

Generally, it is necessary to set a password, because your home can be searched within a certain range near your home, and if it is not encrypted, it is easy for others to hook up to your home's network, not to mention the bandwidth, and security is also a hidden danger.

Further, setting a password is not enough. Now there is a wireless network card on the market that can easily crack the login password of your wireless network. For more security reasons, it's a good idea to also set up Mac filtering:

Only the network card of a specific Mac is allowed to log in. Of course, you have to know the mac of several computers in your home beforehand, add it to the allowlist of the wireless network, and prohibit the login of devices outside the list, which is basically OK.