How to use the Phimaipu genie walk behind floor scrubber

Method Steps:

1.Check the water tank, and remove the sewage in the sewage tank first. Add clean water and a certain percentage of detergent to the clean water tank. Observe the water level ,..

2.Check the control panel and familiarize yourself with the function introduction of each icon and button in advance.

3.Install the brush disk corresponding to the terrain.

4.Turn on the power switch, check the power level, and put down the brush and squeegee.

5.Adjust the working mode and speed to get started.

Regarding the problem of how to reduce the residual sewage on the ground after scrubbing, although many hand-pushed sweepers are provided with a delay of a period of time after turning off the suction motor switch, but because the user does not push the machine forward a little more distance, the sewage between the brush plate and the suction pavement is not sucked dry, which will also lead to residual sewage on the ground, in addition, lifting the suction paddle before turning off the suction motor is also a very good way to reduce the residual sewage on the ground;

Tips to reduce ground wear, we usually find that there are two white circles left on the washed ground when we use the machine, in fact, this is caused by the slight wear and tear of the ground surface caused by the long-term rotation of the floor scrubber, if the machine stops walking when we use the floor scrubber, we must immediately turn off the brush switch to avoid abrasion of the ground, especially for the floor of epoxy resin floor. You can also read the manual carefully.

Just click all three buttons, first click the red power button.

The floor scrubber is a kind of cleaning machinery suitable for cleaning hard floors while sucking up sewage and taking the sewage away from the site, which has the advantages of environmental protection, energy saving and high efficiency. The floor scrubbers are semi-automatic floor scrubbers, automatic floor scrubbers, hand-pushed floor scrubbers, and ride-on floor scrubbers.

The use of floor scrubbers in China is not long, and the use of various fields of society in developed countries has been very common, especially in some stations, docks, airports, workshops, warehouses, schools, hospitals, restaurants, stores and other places with a vast hard floor, the cleaning concept of replacing manpower with machinery has been deeply rooted in the hearts of the people.

Don't you have an instruction manual? The red one should be switched on. As for the rest, I can't understand it.

It's okay, it's okay, it's okay.

This is simple, read more of the manual, and it will be.

It is generally called a walk-behind floor scrubber, which is mainly opened by a key, and generally has a start button and an operating handle. Generally, the drive motor drives the disc brush forward. It is safer to use a maintenance-free battery.

It is best to use a machine with automatic brush removal function, which saves time and effort in maintenance. There are also water-saving systems that save water and detergents.

It is recommended that the hand-pushed floor scrubber of Hagao in Germany have the above functions, and it is very convenient to use.

Precautions for the first use of the international Kuaiba hand-pushed automatic floor scrubber:

First, read the manual of the floor scrubber carefully before use, and use it safely after training. Generally, when the machine is delivered, there will be special after-sales service personnel on-site training for personnel who will use the floor scrubber in the future, precautions and how to use.

2. Please do not operate the machine before it is fully assembled. Before operating the machine, the user should carefully check the integrity of the machine.

3. In the area that needs to be cleaned, first carry out preliminary cleaning, mainly for some non-water-soluble large particles, such as small stones, etc., and other garbage that will affect the work of the suction squeeze, the reason is that the suction squeegee should form a closed space with the ground, so that the sewage can be struck, otherwise it will not work normally if it is not closed. This is a great benefit for you to increase your productivity and protect your machines.

Fourth, the particularly dirty ground can choose to first do not absorb water and repeat the scrubbing many times alone, and then absorb water separately; Or choose a different cleaner to improve the cleaning effect of floor scrubbing.

5. Due to the unevenness of the ground, sometimes although it has been cleaned, if there is still stagnant water, the brush plate can be raised, the water absorption switch can be started, and the floor scrubber can be pushed to absorb repeatedly and repeatedly in the waterlogged area.

6. There is a deep trench on the ground, which will affect the water absorption efficiency of the machine, please deal with it according to the situation at that time.

7. Usually when the brush plate is in the rising position, do not start the brush plate motor at will, otherwise the brush plate will be automatically removed.

1. Clean up the garbage.

Sweeping the epoxy floor, especially the larger garbage, will affect the effect of floor scrubbing, and it needs to be cleaned in time.

2. Pour in clean water.

According to the cleaning area, inject an appropriate amount of clean water into the clean water tank of the floor scrubber, and add an appropriate amount of industrial low-foam cleaning agent according to the degree of oil stain on the ground, and add an appropriate amount of defoamer if necessary.

3. Turn on the switch.

Put down the brush plate, unscrew the key, open the brush plate and water absorption switch, and adjust the amount of water appropriately.

4. Clean at a uniform speed.

At this time, the floor scrubber can be pushed to clean the epoxy floor floor at a uniform speed.

5. Turn off the switch.

When the job is done, turn off the brush switch, lift it up, then turn off the suction switch, and then turn off the key switch.

6. Rinse with water.

Push the floor scrubber to safety, drain the sewage, drain the clean water and rinse.

7. Dry and place.

Leave the scrubber dry and place in a safe and dry place.

1. Using a walk-behind scrubber to clean can effectively protect the floor, and the brush disc of the scrubber is very suitable for cleaning the epoxy floor, and will not cause wear and tear to the floor;

2. The walk-behind floor scrubber is much better than manual cleaning efficiency and effect, it can complete the work of washing, mopping and drying at one time, which can effectively extend the service life of epoxy flooring;

3. When there is oil on the epoxy floor, it is necessary to use detergent to assist the floor scrubber to clean, but when cleaning, it is necessary to pay attention to appropriately adjust the pressure of the brush to protect the ground, use fine and soft brush discs and cleaning pads, and do not use excessive strength and excessive cleaning; Avoid scratching the floor.

The following is the on-site use of Tamon walk-behind floor scrubber to clean epoxy flooring.

1. The water volume of the clean water tank is insufficient. Tuocheng floor scrubber said that when the automatic floor scrubber does not go into the water in the working state, it is necessary to check the clean water tank and inject clean water.

2. The water volume adjustment switch is not turned on. Tuocheng floor scrubber said that if the clean water tank is full, if you don't go into the water, you should check the water volume adjustment switch to see if the water volume adjustment switch is open, if it is not opened, just open it directly.

3. Check the filter. Tuocheng floor scrubber said that if it is not the first two problems, it depends on this. All floor scrubbers have a clean water filter, and the reason why the general floor scrubber does not go into the water is basically that the clean water filter is blocked, and there are sundries in the clean water, so the clean water filter can be removed directly for cleaning, which is an effective method.

4. The outlet pipe is blocked. Tuocheng washing machine said, clean the water pipe, this is also a more common problem, after cleaning the filter screen, or not into the water is also a situation, that is, the clean water pipe is blocked, if there is an air pump, blow it directly, if not, you can remove the water pipe, clean up.

5. The ball valve of the clean water tank is damaged. Tuocheng floor scrubber said that this is the solenoid valve, which is also the switch that controls the clean water.

The above points are the simple reasons why the floor scrubber does not produce water, and when there is a problem, you can judge it yourself!

The 5th episode of the dream of opening the face and acting in the dream of the Dream of Red Mansions, the new scene of the love of the illusion The 6th episode Jia Baoyu tried the cloud and rain for the first time, and Grandma Liu entered the Rongguo Mansion.

The reason why the hand-pushed floor scrubber brush does not produce water:

1. The ball valve of the clean water tank is damaged and needs to be replaced.

2. The water switch is not turned on, it needs to be opened.

3. The water volume of the clean water tank is insufficient, and clean water needs to be injected.

4. The outlet pipe is blocked, the outlet pipe is cleaned, the outlet filter is blocked, and the outlet filter is cleaned or replaced.

The daily maintenance of the floor scrubber can prolong the life of the entire machine, save the cost of use, and improve the efficiency in a short time.

1: Empty and clean the sewage tank.

During the work of the floor scrubber, it is important to remove all the mud and water mixtures inside, as these may emit some unpleasant odors.

2: Empty the clean water tank.

If the floor scrubber itself is not cleaned every day, then there will definitely not be some flowing water, so there can be no impurities, so it is very important to empty the clean water tank.

3: Check the needle disc and cleaning pad.

In the process of using the cleaning pad and the real brand in the floor scrubber, there will be a series of wear and tear, so every time after the use is completed, we must check it, and clean up some of the pollutants on it, and if the wear is left 1 3, then we must replace the cleaning pad in time to prevent wear and tear of the needle disc, so as to reduce maintenance costs.

Peel off the entire strip, and wait until the cleaning is completed, and then use the components of the absorbent strip to put all the raised positions, so as to prevent the damage of the entire strip, and in the process of cleaning, be sure to look at their actual situation.

The problem of the pressure of the brush disc on the ground. There is an adjustment switch at the brush position

The good thing about wiping is that it doesn't absorb water.

**It's all good, but it doesn't absorb water.

What's the deal with mopping machines that don't absorb water.

Three points of personal summary.

1. If the suction motor is broken, you can check the suction power of the suction pipe first, and if not, you must find the manufacturer to sell it and let the professional maintenance personnel repair it.

Second, the angle of the absorbent rubber strip is wrong, in this case, adjust the screw of the absorbent scraper to slowly correct the weight of the absorbent strip, so that the absorbent strip is at a suitable angle.

Third, the last one is to check whether the suction pipe is connected to the suction squeeze, which is the easiest and easiest mistake to make.

- Liang Yuxi.

1. Empty and clean the sewage tank after the use is completed. During the operation of the machine, a large amount of water mixture containing sludge is sucked up, which is very easy to accumulate in the tank and emit an unpleasant odor. If not cleaned in time, the sludge will enter the drain pipe and block the valve pipe, which will affect the next use, so it is necessary to clean the tank with running water.

Second, the water tank of the automatic washing machine must be poured clean after use, especially the automatic cleaning machine is not used every day, otherwise the water that does not flow will become bacteria. It can also cause water leakage due to incorrect operation, causing unnecessary losses (such as burning out the motor).

3. Check whether the suction squeegee of the battery scrubber is clean and clean the absorbent filter, one of the blockages of the suction squeegee and the suction filter will weaken the suction effect, and it is necessary to clean the rubber strip and the filter screen through flowing water.

Fourth, once a week to check the wear of the automatic walk-behind scrubber brush plate and absorbent squeegee, if the ground is relatively frictional, the strong pressure on the ground will damage these accessories or make them wear faster. Under normal circumstances, the brush disc can be replaced after 50 hours of use, on the contrary, the absorbent adhesive strip should be replaced or flipped up and down after 30 hours of use, and the four sides of the adhesive strip are still available.

Shanghai Meimiao Technology Cleaning Equipment is determined to create a professional warehouse-type cleaning products such as floor scrubbers, sweepers, vacuum cleaners and professional detergents for cleaning, and continues to strive to provide one-stop, professional and suitable cleaning equipment and cleaning product solutions for commercial, industrial and service customers.

Regularly inspect the scrubber's brush discs and squeegee for wear and tear, as the strong pressure on the floor can damage these attachments or speed up their wear if the floor is extremely abrasive.

Regularly check the water absorption filter of the floor scrubber, sometimes, the filter will be blocked due to small water impurities, which will affect the outflow of water during the process of cleaning the floor, it is worth noting that it is better to clean with running water.

Clean the drain pipe regularly with clean water to prevent residual detergent from corroding the inner wall of the drain pipe of the floor scrubber and prevent bacteria from growing inside.

When the floor scrubber is not in use, wipe the power cord with a dry cloth after cleaning, and wipe the body and tray (outside and bottom) with a dry cloth.

When the floor scrubber is not in use, wrap the power cord around and hang it on the machine after the battery is fully charged, and also place the machine in a dry and ventilated place to avoid the wet environment affecting the motor and shortening the service life.