How do I remove the lampshade when repairing a vehicle?

When repairing the vehicle, the lampshade is removed by pulling the vertical side of the headlamp high beam twice with a utility knife and cleaning it slightly with a screwdriver. Start heating with a heat gun, first heating the sharp corners of the headlights. Stop heating when the gloves feel a little hot, and scratch hard with both hands on sharp corners.

Once the corners are slightly apart, continue to heat the entire gap of the headlights with a heat gun. After heating, quickly scrape the corners and scrape hard, and then the headlight cover of the car can be removed. The surface of the lampshade has a special coating, which is resistant to oxidation and sun and rain, and even ordinary sharp objects will not be scratched.

This coating process requires high-temperature baking.

1.The automobile lamp shade is connected with the headlight assembly. To disassemble the car lamp cover, the entire headlight assembly must be removed, and the car lamp cover cannot be replaced separately.

Remove the headlamp, then remove the upper and lower screws. If there are screws on the lampshade and then remove the screws, you can remove the car lampshade, if not, you can only replace the headlamp assembly.

2.The car lampshade is broken. The best and most effective way to do this is to replace the lampshade.

If it is not replaced, it is likely to cause water ingress, which will not only affect the brightness of the light, but also cause a short circuit in the light and damage to the circuit. It is estimated that some car owners will use tape or **sol to repair, but these methods will seriously affect the light of the car headlights, so try not to use such methods. Remove the headlight shade and clean the colloids and dust inside the grooves.

Fill the grooves with new sealant, press the new shade tightly, and wipe off the spilled sealant. It is best to test whether the lampshade is suitable before applying the sealant and make sure that the fluid in the glue tank is clean, otherwise the sealing performance may be affected after replacing the lampshade with a new one. After completing the above process, wipe the headlights dry, and then put them back in the car for normal use.

3.As the eyes of the car, once the car lights become weak or the bulb is damaged, and the car lampshade turns yellow, the car headlights should be repaired or replaced in time to avoid not being able to see the road clearly when driving at night, because driving at night itself has a bad line of sight, and if you add light problems, the danger of driving at night will increase. The above is the answer to the question of how to disassemble the lampshade when repairing the vehicle.

First of all, you must prepare a change cone, and also prepare a jack, and then use the change cone to remove all the screws, and then you can remove the lampshade, but you must pay attention to safety when dismantling, and do not let yourself be injured.

You can heat it first, use a utility knife, gently scrape it in the gap, and try to use some special tools, otherwise it is easy to damage the headlights.

This lamp and lampshade are integral, and it is more troublesome and complicated to disassemble the lampshade separately, and it is necessary to replace the whole lampshade together.

1. Round ceiling lampshade

Before disassembly, you need to cut off the power switch of the light. Only after the power is off can the disassembly safety be guaranteed.

Since round ceiling lamps are usually opened by rotating the shade, a screwdriver is required.

Slowly remove the small screws around the iron ring of the lampshade. When the lampshade is loose and can be turned, turn the lampshade again until it is unscrewed, and finally the lampshade can be removed. That's it.

2. Recessed ceiling lamp

Since this lamp is installed directly in the integrated suspended ceiling.

up, it seems that there is nowhere to start. In fact, it is not difficult to remove the lampshade of this lamp.

Recessed ceiling lights are stuck in the ceiling.

Above. Before removing the lampshade, you need to cut off the power supply first, then remove the ceiling gusset, and then look carefully, you will find that the embedded ceiling lamp is blocked by a spring clip. Yes, cut it off.

3. Aluminum gusset ceiling lamp

For this type of fixture, it is not possible to remove the lampshade by rotating it directly. The correct thing to do is to cut off the power supply first, and then use a small screwdriver or small blade to tilt a corner from the seam of the aluminum gusset, remove the gusset around the lamp, and you can see that there are two lights on the ceiling. Similar to downlights.

Buckle of snap buckle.

Then use two stiffer plastic cards, insert them along the corners of the gusset, move the card to the other end, pry it off with a little force, and finally pull out the gusset by hand and remove the lampshade.

4. Rectangular ceiling lamp

Compared to round lights, this type of light is more cumbersome to disassemble. First, you need to cut off the power and then locate the four corners around the light.

After that, you can borrow the dishwashing hook of the suction cup, suction the aluminum part on the side, and slowly pull down, pulling each corner until the lampshade is removed. In the process of pulling, the action should be slow and not too forceful, so as not to directly damage the lamp or re-work.

Different types of lamps and lanterns have different methods of disassembling lampshades.

1. Round ceiling lampshade

Before dismantling, the power switch of the lamp needs to be cut off, and only after the power supply is cut off, can the disassembly safety be guaranteed. Because the round ceiling lamp is usually opened by rotating the lampshade, it is necessary to slowly remove the small screws around the iron ring of the lampshade with the help of a screwdriver, and when the lampshade is loose and can be rotated, the lampshade can be rotated until it is unscrewed, and finally the lampshade can be removed.

2. Recessed ceiling lamp

Since these luminaires are mounted directly with the integrated ceiling and seem to have nowhere to start when dismantling, the lampshade of such luminaires is actually not difficult to remove. The recessed ceiling lamp is stuck in the ceiling, before taking the lampshade, the same needs to cut off the power supply first, and then remove the ceiling gusset, and then observe carefully, you will find that the recessed ceiling lamp has a spring clip to jam it, and it can be broken off.

3. Aluminum gusset ceiling lamp

For such luminaires, it is not possible to remove the lampshade if it is rotated directly. The correct way should be to cut off the power supply first, and then use a small screwdriver or a small thin blade to warp a corner from the seam edge of the aluminum gusset, and remove any gusset around the lamp, and you can see that there are two spring buckles similar to downlight buckles on the ceiling lamp. Then use two harder plastic cards, insert them into the corners of the extension plate, move the card to the other end, pry down a little bit of the gap with a little force, and finally pull out the gusset by hand and remove the lampshade.

4. Rectangular ceiling lamp

Compared to round luminaires, this type of luminaire will be more cumbersome to disassemble. First of all, you need to cut off the power supply, and then find the four corners around the lamp, you can borrow the washing hook of the suction glass disc, suck it on the aluminum alloy part on the side, and slowly pull down, pulling at each corner until the lampshade is removed. In the process of pulling, the action should be slow and not too forceful, so as not to directly damage the lamp or exert force again.

The method of disassembling the lampshade as soon as you learn it.

How to remove the car headlight cover: Draw the vertical side of the headlamp high beam twice with a utility knife and clean it slightly with a screwdriver. Start heating with a heat gun.

Start by heating the sharp corners of the headlights. When the gloves feel a little hot, stop the heat. Grab the sharp corners with both hands and scrape hard.

After the corners are slightly apart, use the heat gun to continue to heat the entire gap of the headlights. After heating, quickly scrape the corners, scrape hard, and you can remove the headlight cover of the car. The surface of the lampshade is specially coated to resist oxidation, sun and rain, and even sharp objects will not be scratched.

This coating process requires high temperature baking.

Once the headlights are off, the most important job to do: stripping the shade. The tools to use are:

Hair dryer, flathead screwdriver, gloves. Gloves are very important and must be worn, otherwise they will be easily burned. First use a flathead screwdriver to pry open the four clips, then put on gloves in your right hand, hold the headlight, hold the hair dryer in your left hand, turn it on to the hottest position, aim at the sharp corners of the headlight, and blow hard at a close distance (3 5cm) for 20 30 seconds.

At this time, you will feel a little hot with your gloved hands. Estimated around 80. If you look closely at the corner of the lamp, you will find that there is a small one between the lampshade and the black lamp body behind it.

At this time, you can turn off the hair dryer, insert a flathead screwdriver into the slot of your left hand, and pry the headlight cover outward. Be careful in this step, don't be in a hurry, otherwise it is easy to pry the lamp body.

After prying a little, continue to blow along the seam with a hair dryer, continue to pry hard, and pull the lampshade hard. At this time you will notice that the seam is getting bigger and bigger. Keep it up like this.

Turn off the headlights. Car headlights are generally fixed with buckles or screws, and the headlights can be removed after pulling out the buckles or removing the screws. When disassembling, take care to protect the wiring harness on the headlamp.

Heat the area around the lampshade with a heat gun until it feels hot. If you can't pry it open, continue to heat. If you don't have a heat gun, you can use a high-power hair dryer, but a low-power hair dryer can't, or you can boil it directly with hot water.

Remove the lampshade and clean the colloids and dust from the grooves. Fill the grooves with new sealant, then press the new shade cover and wipe off the spilled sealant. It is best to test whether the lampshade is suitable before applying the sealant and make sure that the fluid in the glue tank is cleaned, otherwise it may cause a poor seal after replacing the lampshade with a new one.

After the above steps are completed, the headlights can be put back to the original way for normal use after drying. In order to ensure tightness and firmness, the sealant must be dried before loading.

First of all, you should use professional tools to dismantle, it is best not to wear too much damage to the surroundings, and invite professional personnel to deal with it, and use larger tools to remove it.

If you want to disassemble this car lamp cover, in fact, the best way is to use a special one, the effect of this appliance is very good when dismantled, and after dismantling, you will find a special brightness.

In fact, there is a way to remove the lampshade of the car, we only need to find the other party, if it really doesn't work, go to the 4S store or the decoration shop to disassemble.

Car lampshades are generally made of gel glue, and if you disassemble the car lampshades, you need to use heating to open the lampshades.

How to disassemble the car lamp cover? Steps to disassemble the automobile lamp cover: 1. Remove the headlight assembly, which is generally buckled or fixed by screws; 2. Use a heat gun to heat the lampshade around, and slowly pry open the lampshade after softening the lampshade fixing glue, 3. Remove the headlamp lampshade, clean the fluid in the groove, and then fill in the new sealant, press the new lampshade cover, and erase the spilled sealant; 4. After drying, the headlight assembly can be installed back.

If the lampshade is broken, it is recommended to replace the headlight assembly, replacing the lampshade alone does not ensure its tightness. Car headlights, also known as car headlights, car LED daytime running lights, as the eyes of the car, are not only related to the external image of a car owner, but also closely related to safe driving at night or in bad weather conditions. @2019

Open the tailgate, see two plastic fastening buckles inside, remove them with tools, open the interior panel first to see the fastening screws inside, and remove them directly. When taking out the tail light, pay attention to the line of the tail light not to break, and the plug should be protected.

1. Disassembly of the trunk lining cotton.

After the trunk is opened, you need to remove the lining cotton on the side of the rear taillight, you will find that the fixed lining cotton is a few plastic buckles, at this time you need to use a small word change cone to pry these buckles, and then use your hands to pick up the lining cotton, it should be noted that you should be slow when prying, do not pry the plastic buckles.

2. Disassembly of the tail light nut after fixing.

There are three nuts to fix the rear tail lights of the car, take out the small wheel, match the No. 8 sleeve, and then remove the three nuts fixed on it one by one and put them away.

3. Dismantling of the rear tail light wiring harness.

The tail light wiring harness is a wire plug, you only need to unplug the wiring harness plug by hand, if it is not easy to pull out, use a small word to change the cone and gently pry it.

4. Replace the rear taillights.

After unplugging the wiring harness, you can remove the rear taillight, hold both sides of the rear taillight with two hands, and then gently pull it out, gently shaking it while pulling, so that it can be removed, and the attention channel is not too large, so that you can easily complete the whole process of how to disassemble the rear taillight of the car. (Photo by Chen Min 2 of Pacific Automobile Network).

Hello dear! Glad for your question! how to remove the lampshade; The first part introduces the disassembly method of rectangular ceiling lamps.

The steps are as follows:1. cut off the power supply; 2.

Remove the lampshade. This kind of lampshade should start from its four corners, use the dishwashing hook of the glass suction cup to suck the aluminum alloy part on the side, and slowly pull it down, pulling all four corners down until the lampshade is removed. 3.

Remove the bulb 4. The second method introduces the disassembly method of aluminum gusset ceiling lamp.

Cut off the power supply first, then use a small screwdriver or a thin blade to tilt an angle from the connecting edge of the aluminum gusset, remove the lampshade 5, and pull down a small aluminum gusset plate in the same way. Then the disassembly method of the embedded ceiling lamp is to cut off the power supply first, and then find a safety clip to disconnect. The dismantling method of crystal ceiling lamp is to disassemble all the accessories first, then disassemble the lamp tube, and finally disassemble the ceiling panel.

Hello oh kiss The method of disassembling the lampshade is as follows: The steps are as follows: 1. Cut off the power 2. Take out the lampshade.

This kind of lampshade should start from its four corners, use the dishwashing hook of the glass suction cup, suck the aluminum alloy part on the edge, slowly pull down, pull all the four corners, until the lampshade is removed 3, remove the bulb 4, the second method introduces the disassembly method of the aluminum gusset ceiling lamp: first cut off the power supply, then use a small screwdriver or a small thin blade to tilt a corner from the edge of the seam of the aluminum gusset, remove the lampshade 5, pull down a small piece of aluminum gusset with the same method, and then take out the bulb. The way to remove the recessed ceiling light is to first cut off the power supply, then find the spring clip and disconnect it.

The method of dismantling the crystal ceiling light is to remove all the accessories first, then the tube, and finally the ceiling panel. And take out the lampshade, take out the lampshade. This shade starts at its four corners.

Use the disc hook of the glass suction cup to suck the aluminum alloy part on the side and slowly pull it down.